So STEFFCO racing down in SC has been working on this 424NAX GEN 3 HEMI BUILD for me. Check it out.

6.1 Block
Thitek Built Eagle Heads
4.07 Bore. 4.08 Stroke. 424 CID
K1 Technology Crank & Rods
Diamond Custom Pistons 12:5 Pump Gas / MS109 at the Track.
Hellcat Fuel Injectors
102MM Throttle Body
Holley Intake
Johnson Short Travel with Axle Oiling Lifters
AAD Aluminum Lifter Guides
Milodon Oil Pump Pickup & Pan
Manley Timing Chain
Mike Jones CAMSHAFT
Machine Work was done at Harrell Engines

I'm so excited, I just wanted to show off. Simple as that.

Bubba

Greatly appreciate you sharing, shiw more of the entire build please!

I agree

I’ve always had 2 issues that bothered me. Weight and Speed.
1965 Coronet
1980 Mirada
1970 Coronet
2005 Magnum RT
2012 Challenger RT
2006 Jeep SRT

The average weight of these vehicles is 4350 Lbs. Time to be different!

Welcome to my current project.
1987 Chevrolet El CAMINO. Better know for the last few years as the
EL HEMINO in my family.

PROJECT: EL HEMINO

424” Gen 3 Hemi
T-400 Transmission
Ford 9”
PTS Fab K-Frame with Rack
TRZ Front and Rear Suspension
Strange Brakes
AFCO Shocks Front and Rear
Full Cage 8.50 Cert
Full Interior from 1987
All Steel. Even bumpers
Hemi Hood Scoop


My intentions are to wheel this thing around the block a few days a week, hit some car shows and definitely the drag strip. I am not chasing numbers, so I don’t care how fast it goes.
The car is headed down to SteffCo Racing in SC for all the Cage and Chassis/Frame work next month.

I know it’s not a Mopar on the outside.

Cool project! I like different stuff. Cant wait to see it running!

Thank you.

What's the weight estimate?

No solid estimates yet. Less than 4K.

The PTS FAB Kit is a game changer. Weight / Strength, and headers will be off the shelf.

From a family who owns an 84 SS since new, this one hits really close to home! Awesome

No way Jim! That’s super cool.
I’ll keep ya posted.

I like it better than these idiots that want to stick a Chevy motor in everything else, especially these days a freaking "LS something"...... I get so damn tired of hearing about that BS.
But a turbo 400? Wouldn't a 727 be a better bet?

I like it.
Are you using a aftermarket T400 case? What ECU are you planning on using?
Looks like a fun project.

I don't get the obsession with the turbo 400 either, 727 is just as good. TH400 still explode, still cost big money to handle big HP, almost identical gear ratios, heavier, requires adapter plate or bellhousing, if you put one in a mopar then it don't bolt up to your trans mount and your slip yolk don't fit...

Dodge uses the Turbo 400 in some of the Drag Packs. In my opinion the biggest reason is the availability of the SFI case. Which eliminates the PIA blankets and shields.

Who said there was an obsession with a T400?
And if there was, wouldn't that state the obvious?
I'm not here to debate. 904/727/T400/4L80 Use what makes YOU happy, what YOU pay for, and what gets YOUR job done.

On the other hand, I do have a obsession with my FORD 9".. if anyone would you care to join me? an 8 3/4 to a 9"? Dana 60 to a 9"?
I'll take the weight savings from the 9" to make up for the use of a junk T400.

Holley Terminator X setup for all controls.

Dana 60 only , 40 spline spool and axles and shorten it for your car for the wider rims and tires. Live forever, last a long time
Less drag also
As far as drag racing tranny go Pro Flytes
There is an HP amount that you do need to go to an all out drag racing only H.D. turbo 400 type tranny, probably above 1500 HP

Not that my opinion means anything, but I like it. Thanks for sharing Bubba.

Some of these members are seriously mopar or no car. Good for them. I agree, your money, your car, end of story. Lots of reasons people pick a 9 over any other rear. Keep doing what you're doing.

Looking good Todd! I always liked that body style. I think the moniker WhiteDevil fits better? lol But, like you said YOUR MONEY, YOUR CHOICES!

Thank you guys.. I will keep up with progress pics and notes as she goes.