|
Cast core crane solid roller
#3185102
10/19/23 05:17 PM
10/19/23 05:17 PM
|
Joined: May 2006
Posts: 1,075 oregon
greendart408
OP
super stock
|
OP
super stock
Joined: May 2006
Posts: 1,075
oregon
|
Now before anyone says it, I know these aren’t ideal. I would never buy one new. It’s not the specs I would choose But.. I purchased a old school built in 74 340. Has the typical dome trw’s and all the mods and parts a person could buy then. Full effort from back in the day. It has a crane r280/427-8 solid roller. It’s a cast unit. I’m putting together a car from all my spare leftover parts from over the yrs since I have it and for fun. Do I dare run this???? Calls for 170lb seat and 485lb open. Will have a good set of w2s, stock stroke, ram rod, cragars etc etc. A fun day 2 street machine.
Last edited by greendart408; 10/19/23 05:31 PM.
|
|
|
Re: Cast core crane solid roller
[Re: greendart408]
#3185108
10/19/23 06:02 PM
10/19/23 06:02 PM
|
Joined: Feb 2005
Posts: 20,203 PA.
pittsburghracer
"Little"John
|
"Little"John
Joined: Feb 2005
Posts: 20,203
PA.
|
I’m running a Racer Brown cast roller .660 lift cam in my 408 that Jim made for a buddy of mine and I bought from him. It’s gone 5.98 so far.
1970 Duster Edelbrock headed 408 5.984@112.52 422 Indy headed small block 5.982@112.56 mph 9.42@138.27
Livin and lovin life one day at a time
|
|
|
Re: Cast core crane solid roller
[Re: greendart408]
#3185220
10/20/23 09:18 AM
10/20/23 09:18 AM
|
Joined: Feb 2005
Posts: 20,203 PA.
pittsburghracer
"Little"John
|
"Little"John
Joined: Feb 2005
Posts: 20,203
PA.
|
Thanks, that’s what I wanted to hear. Pittsburg, how much spring pressures are you running? Closed and open. Here’s the cam card. It’s on the bottom
1970 Duster Edelbrock headed 408 5.984@112.52 422 Indy headed small block 5.982@112.56 mph 9.42@138.27
Livin and lovin life one day at a time
|
|
|
Re: Cast core crane solid roller
[Re: pittsburghracer]
#3185234
10/20/23 10:14 AM
10/20/23 10:14 AM
|
Joined: May 2006
Posts: 1,075 oregon
greendart408
OP
super stock
|
OP
super stock
Joined: May 2006
Posts: 1,075
oregon
|
Thanks, that’s what I wanted to hear. Pittsburg, how much spring pressures are you running? Closed and open. Here’s the cam card. It’s on the bottom Thank you much
|
|
|
Re: Cast core crane solid roller
[Re: greendart408]
#3185235
10/20/23 10:15 AM
10/20/23 10:15 AM
|
Joined: Feb 2005
Posts: 20,203 PA.
pittsburghracer
"Little"John
|
"Little"John
Joined: Feb 2005
Posts: 20,203
PA.
|
Thanks, that’s what I wanted to hear. Pittsburg, how much spring pressures are you running? Closed and open. Here’s the cam card. It’s on the bottom Thank you much You are very welcome
1970 Duster Edelbrock headed 408 5.984@112.52 422 Indy headed small block 5.982@112.56 mph 9.42@138.27
Livin and lovin life one day at a time
|
|
|
|
|
|