WIRING LABEL MAKER - Moparts Forums

Register Log In Moparts Forums Unlawfl's Race & Engine Tech WIRING LABEL MAKER

Print Thread

WIRING LABEL MAKER #2599622 01/01/19 02:50 AM 01/01/19 02:50 AM
Joined: Oct 2008 Posts: 1,176 East Coast A A/MP OP super stock
A/MP OP super stock A Joined: Oct 2008 Posts: 1,176 East Coast	Winter time/wiring time. I want a better system than tape and a sharpie. Anyone have a label maker that might survive an engine compartment?

Re: WIRING LABEL MAKER [Re: A/MP] #2599633 01/01/19 03:14 AM 01/01/19 03:14 AM
Joined: Feb 2005 Posts: 20,173 PA. pittsburghracer "Little"John
pittsburghracer "Little"John Joined: Feb 2005 Posts: 20,173 PA.	Originally Posted By A/MP Winter time/wiring time. I want a better system than tape and a sharpie. Anyone have a label maker that might survive an engine compartment? I would check out a company like Leach Electronics to see if they offer something 1970 Duster Edelbrock headed 408 5.984@112.52 422 Indy headed small block 5.982@112.56 mph 9.42@138.27 Livin and lovin life one day at a time

Re: WIRING LABEL MAKER [Re: A/MP] #2599634 01/01/19 03:15 AM 01/01/19 03:15 AM
Joined: Oct 2006 Posts: 119 Massachusetts, USA maxeffort member
maxeffort member Joined: Oct 2006 Posts: 119 Massachusetts, USA	The label makers that print on heat shrink tube. Ive had a Brady tube printer for about ten years. It works well, but it’s a slow process to print and shrink. Its nice when done. Dymo and others also make them I have read that you can use the Dymo heat shrink tube cartridges in their cheaper printers. official member of the Sleepy Labeef band alumni club.

Re: WIRING LABEL MAKER [Re: maxeffort] #2599640 01/01/19 03:32 AM 01/01/19 03:32 AM
Joined: Jun 2007 Posts: 493 gr mich L loren kraker mopar
loren kraker mopar L Joined: Jun 2007 Posts: 493 gr mich	Check out wirelm .com. got all my labels from him and good quality

Re: WIRING LABEL MAKER [Re: A/MP] #2599738 01/01/19 12:20 PM 01/01/19 12:20 PM
Joined: Dec 2009 Posts: 305 Mesa, AZ cagebob1 enthusiast
cagebob1 enthusiast Joined: Dec 2009 Posts: 305 Mesa, AZ	print the labels you want on your computer, trim to size, then insert under clear shrink tube, shrink. Viola ... custom wire labels!

Re: WIRING LABEL MAKER [Re: cagebob1] #2599814 01/01/19 01:50 PM 01/01/19 01:50 PM
Joined: Feb 2005 Posts: 20,173 PA. pittsburghracer "Little"John
pittsburghracer "Little"John Joined: Feb 2005 Posts: 20,173 PA.	http://www.wirelm.com/labels.htm https://www.ronfrancis.com/products.asp?dept=312 Amazon list several but I couldn't get the link to copy right. Last edited by pittsburghracer; 01/01/19 01:53 PM. 1970 Duster Edelbrock headed 408 5.984@112.52 422 Indy headed small block 5.982@112.56 mph 9.42@138.27 Livin and lovin life one day at a time

Re: WIRING LABEL MAKER [Re: A/MP] #2599949 01/01/19 03:58 PM 01/01/19 03:58 PM
Joined: Jan 2003 Posts: 25,785 Rio Linda, CA John_Kunkel Too Many Posts
John_Kunkel Too Many Posts Joined: Jan 2003 Posts: 25,785 Rio Linda, CA	Here's what I use: https://www.ebay.com/itm/BROTHER-P-TOUCH...GE/183491449828 The INTERNET, the MISinformation superhighway

Re: WIRING LABEL MAKER [Re: A/MP] #2600037 01/01/19 06:40 PM 01/01/19 06:40 PM
Joined: Dec 2005 Posts: 11,551 Fulton County, PA C CMcAllister Mr. Helpful
CMcAllister Mr. Helpful C Joined: Dec 2005 Posts: 11,551 Fulton County, PA	Race car? Unless it's really complex, I just use a large selection of wire colors to organize the system and it's different tangents. If it's one of those deals where there are 3 wire colors used than yes, labels will be helpful. And I like the self-printed labels under clear shrink idea. Plan before you start stringing wires. If the results don't match the theory, change the theory.

Re: WIRING LABEL MAKER [Re: A/MP] #2600165 01/01/19 10:00 PM 01/01/19 10:00 PM
Joined: Jan 2012 Posts: 2,645 Stuttgart, Arkansas rickseeman master
rickseeman master Joined: Jan 2012 Posts: 2,645 Stuttgart, Arkansas	Mine is a Rhino 4200. I like it. There are many different sizes available. www.labelcity.com is one of the places to buy them. Get plenty of heat shrink tubes also. Last edited by rickseeman; 01/01/19 10:00 PM. 2011 Drag Pak Challenger

Re: WIRING LABEL MAKER [Re: John_Kunkel] #2600233 01/01/19 11:34 PM 01/01/19 11:34 PM
Joined: Jun 2009 Posts: 877 ky 68roadrunner super stock
68roadrunner super stock Joined: Jun 2009 Posts: 877 ky	Originally Posted By John_Kunkel Here's what I use: https://www.ebay.com/itm/BROTHER-P-TOUCH...GE/183491449828 this prints on the heat shrink?

Re: WIRING LABEL MAKER [Re: 68roadrunner] #2600479 01/02/19 03:57 PM 01/02/19 03:57 PM
Joined: Jan 2003 Posts: 25,785 Rio Linda, CA John_Kunkel Too Many Posts
John_Kunkel Too Many Posts Joined: Jan 2003 Posts: 25,785 Rio Linda, CA	No, it just prints an adhesive strip label that I wrap around the wire or bundle. The INTERNET, the MISinformation superhighway

Re: WIRING LABEL MAKER [Re: A/MP] #2600551 01/02/19 06:09 PM 01/02/19 06:09 PM
Joined: Jan 2003 Posts: 19,363 Las Vegas Al_Alguire I Live Here
Al_Alguire I Live Here Joined: Jan 2003 Posts: 19,363 Las Vegas	I have and use a Dymo label makes and their heat shrink to label all my wiring. "I am not ashamed to confess I am ignorant of what I do not know." "It's never wrong to do the right thing"

Re: WIRING LABEL MAKER [Re: A/MP] #2600667 01/02/19 09:59 PM 01/02/19 09:59 PM
Joined: Jan 2003 Posts: 2,813 Blue Ridge, VA Plumb Wired master
Plumb Wired master Joined: Jan 2003 Posts: 2,813 Blue Ridge, VA	Dymo 4200 w/ various diameters of heat shrink here. http://www.dymo.com/en-US/dymo-labeling-...qwy-label-maker RIP Monte Smith aka: OutlawFish '98 Bickel Dodge Dakota PST

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1