Re: Who can CNC W2 heads?
[Re: Htownmopar]
#2256267
02/19/17 10:27 PM
02/19/17 10:27 PM
|
Joined: Jan 2003
Posts: 11,728 Portage,michigan
B3422W5
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 11,728
Portage,michigan
|
Try modern cylinder head. They don't have W2 listed as a CNC option but may well do it. They don't have the eddies listed either, or W5, but know they do both of those
69 Dart GTS A4 Silver All steel, flat factory hood, 3360race weight 418 BPE factory replacement headed stroker, 565 lift solid cam Best so far, low 10.30’s 1/4 1.41 best 60 foot 6.56 at 104.17
|
|
|
Re: Who can CNC W2 heads?
[Re: B3422W5]
#2256270
02/19/17 10:30 PM
02/19/17 10:30 PM
|
Joined: Jan 2003
Posts: 6,150 Melbourne , Australia
LA360
master
|
master
Joined: Jan 2003
Posts: 6,150
Melbourne , Australia
|
Brett Miller, send him a PM. I think he has dabbled in these.
Larry Meaux would be the other person I would speak with, does a lot of Super Stock stuff
Alan Jones
|
|
|
Re: Who can CNC W2 heads?
[Re: Htownmopar]
#2256454
02/20/17 03:40 AM
02/20/17 03:40 AM
|
Joined: Jan 2003
Posts: 3,505 DFW
mr_340
master
|
master
Joined: Jan 2003
Posts: 3,505
DFW
|
I had MCH do a set for me many years ago when Jeff was still around.
Floyd Lippencott IV
|
|
|
Re: Who can CNC W2 heads?
[Re: dwayne welder]
#2257780
02/22/17 03:33 PM
02/22/17 03:33 PM
|
Joined: Feb 2005
Posts: 20,201 PA.
pittsburghracer
"Little"John
|
"Little"John
Joined: Feb 2005
Posts: 20,201
PA.
|
I don't like the .300 lift numbers at all on that flow sheet. 179 @.300 is pathetic on a ported head. Especially on a head upgraded to a 2.08 intake valve.
1970 Duster Edelbrock headed 408 5.984@112.52 422 Indy headed small block 5.982@112.56 mph 9.42@138.27
Livin and lovin life one day at a time
|
|
|
Re: Who can CNC W2 heads?
[Re: pittsburghracer]
#2257787
02/22/17 03:49 PM
02/22/17 03:49 PM
|
Joined: Oct 2011
Posts: 3,036 bean town ....Ca
WHITEDART
master
|
master
Joined: Oct 2011
Posts: 3,036
bean town ....Ca
|
I don't like the .300 lift numbers at all on that flow sheet. 179 @.300 is pathetic on a ported head. Especially on a head upgraded to a 2.08 intake valve. I don't think it matters much what the head does at 300 on a race head. The early numbers go right out the exhaust port
Last edited by WHITEDART; 02/22/17 03:59 PM.
In the 8s N/A.with Brett miller W8's 5.07 at 133 at 2700lb
|
|
|
Re: Who can CNC W2 heads?
[Re: WHITEDART]
#2257796
02/22/17 04:20 PM
02/22/17 04:20 PM
|
Joined: Feb 2005
Posts: 20,201 PA.
pittsburghracer
"Little"John
|
"Little"John
Joined: Feb 2005
Posts: 20,201
PA.
|
I don't like the .300 lift numbers at all on that flow sheet. 179 @.300 is pathetic on a ported head. Especially on a head upgraded to a 2.08 intake valve. I don't think it matters much what the head does at 300 on a race head. The early numbers go right out the exhaust port Keep in mind everyone doesn't run an .800 lift cam in their small block or shift at 8000 plus RPM.
1970 Duster Edelbrock headed 408 5.984@112.52 422 Indy headed small block 5.982@112.56 mph 9.42@138.27
Livin and lovin life one day at a time
|
|
|
Re: Who can CNC W2 heads?
[Re: Htownmopar]
#2257806
02/22/17 04:45 PM
02/22/17 04:45 PM
|
Joined: Jan 2003
Posts: 3,505 DFW
mr_340
master
|
master
Joined: Jan 2003
Posts: 3,505
DFW
|
That was Jeff's first go on the ports. He worked on them a bit more to pick up the lower lifts. My W5 heads did flow better than the .300" number and that was as cast with a Ø2.06" BBC stock valve.
Floyd Lippencott IV
|
|
|
Re: Who can CNC W2 heads?
[Re: pittsburghracer]
#2257810
02/22/17 04:53 PM
02/22/17 04:53 PM
|
Joined: Oct 2011
Posts: 3,036 bean town ....Ca
WHITEDART
master
|
master
Joined: Oct 2011
Posts: 3,036
bean town ....Ca
|
I don't like the .300 lift numbers at all on that flow sheet. 179 @.300 is pathetic on a ported head. Especially on a head upgraded to a 2.08 intake valve. I don't think it matters much what the head does at 300 on a race head. The early numbers go right out the exhaust port Keep in mind everyone doesn't run an .800 lift cam in their small block or shift at 8000 plus RPM. they dont? Well who cares then 😜.. John I'm just poking👉 carry on
Last edited by WHITEDART; 02/22/17 05:11 PM.
In the 8s N/A.with Brett miller W8's 5.07 at 133 at 2700lb
|
|
|
Re: Who can CNC W2 heads?
[Re: pittsburghracer]
#2257883
02/22/17 08:44 PM
02/22/17 08:44 PM
|
Joined: Jul 2009
Posts: 494 IL
EchoSixMike
mopar
|
mopar
Joined: Jul 2009
Posts: 494
IL
|
I don't like the .300 lift numbers at all on that flow sheet. 179 @.300 is pathetic on a ported head. Especially on a head upgraded to a 2.08 intake valve. I don't think it matters much what the head does at 300 on a race head. The early numbers go right out the exhaust port Keep in mind everyone doesn't run an .800 lift cam in their small block or shift at 8000 plus RPM. Slackers. S/F....Ken M
|
|
|
Re: Who can CNC W2 heads?
[Re: killermopar]
#2257915
02/22/17 10:01 PM
02/22/17 10:01 PM
|
Joined: Feb 2005
Posts: 20,201 PA.
pittsburghracer
"Little"John
|
"Little"John
Joined: Feb 2005
Posts: 20,201
PA.
|
Heck that's where that W8 and W9 stuff starts coming on. Lol
1970 Duster Edelbrock headed 408 5.984@112.52 422 Indy headed small block 5.982@112.56 mph 9.42@138.27
Livin and lovin life one day at a time
|
|
|
Re: Who can CNC W2 heads?
[Re: pittsburghracer]
#2257931
02/22/17 10:24 PM
02/22/17 10:24 PM
|
Joined: Oct 2011
Posts: 3,036 bean town ....Ca
WHITEDART
master
|
master
Joined: Oct 2011
Posts: 3,036
bean town ....Ca
|
Heck that's where that W8 and W9 stuff starts coming on. Lol you bet RPM is king..8000 is good 9000 is better💣
In the 8s N/A.with Brett miller W8's 5.07 at 133 at 2700lb
|
|
|
|
|