Any guesses what this combo may run?
#1638201
06/25/14 02:40 AM
06/25/14 02:40 AM
|
Joined: Feb 2004
Posts: 4,501 Gainesville,FL
goldmember
OP
master
|
OP
master
Joined: Feb 2004
Posts: 4,501
Gainesville,FL
|
The combo is a 1990 Dakota street truck(approx 3550-3600lbs with driver),3.73's,stockish 727, PTC 9.5" converter that flashed 3800 with the former stock lower end 360 magnum, 750HP holley, 1 5/8" Hooker headers,Edelbrock RPM intake. The new shortblock is 408" with 10.2 to 1 comp, hyd roller 237/245 .585 108lsa in @ 105,Same Magnum R/T heads 2.02/1.6 no flow bench help ,valve springs are 170/395open doubles. Other than increased cubes,slight comp increase,10ish degrees more duration and slight lift(area increase)it's the same as it has been for years. LOL any guesses? Should know some answers Friday nite so.......Why not take a shot??
Last edited by goldmember; 06/25/14 02:44 AM.
|
|
|
Re: Any guesses what this combo may run?
[Re: Chris2581]
#1638204
06/29/14 10:57 PM
06/29/14 10:57 PM
|
Joined: Feb 2004
Posts: 4,501 Gainesville,FL
goldmember
OP
master
|
OP
master
Joined: Feb 2004
Posts: 4,501
Gainesville,FL
|
Both good guesses and mine was 11.20ish. the truck made 4 or 5 passes and went a best of [Email]11.33@117mph.[/Email] I guess with the poor conditions,over 20% converter slip and other easy things to correct(no tuning done etc) a 10.90 is in there somewhere. The guy that owns it wanted an 11.50 in the heat so we are well past that point.The best with the old short was 11.92 in great conditions(average around 12.20).
Last edited by goldmember; 06/29/14 11:01 PM.
|
|
|
Re: Any guesses what this combo may run?
[Re: viperblue72]
#1638207
07/01/14 02:41 AM
07/01/14 02:41 AM
|
Joined: Feb 2004
Posts: 4,501 Gainesville,FL
goldmember
OP
master
|
OP
master
Joined: Feb 2004
Posts: 4,501
Gainesville,FL
|
Quote:
Runs good.
Thanks and yes, I thought it was a good first outing with a simple combo with limiting features. All I did was add a little timing as I was too busy sweating to feel like doing more on it's first outing.
|
|
|
Re: Any guesses what this combo may run?
[Re: mshred]
#1638208
07/01/14 02:50 AM
07/01/14 02:50 AM
|
Joined: Feb 2004
Posts: 4,501 Gainesville,FL
goldmember
OP
master
|
OP
master
Joined: Feb 2004
Posts: 4,501
Gainesville,FL
|
Quote:
Nice times! With some tuning it might see Eleven O's/ 10 90's!
Yep,there is more left for sure and in great air even without tuning it would pick up a couple numbers. The trouble is this combo will see 150 or so shot of N20 and the converter is already in distress without any help. LOL I will talk to Kenny and come up with a plan to get things on the right track.The stone stock rpm intake manifold is another issue.
|
|
|
Re: Any guesses what this combo may run?
[Re: goldmember]
#1638209
07/01/14 10:33 AM
07/01/14 10:33 AM
|
Joined: Apr 2009
Posts: 3,416 Toronto
mshred
master
|
master
Joined: Apr 2009
Posts: 3,416
Toronto
|
Quote:
Quote:
Nice times! With some tuning it might see Eleven O's/ 10 90's!
Yep,there is more left for sure and in great air even without tuning it would pick up a couple numbers. The trouble is this combo will see 150 or so shot of N20 and the converter is already in distress without any help. LOL I will talk to Kenny and come up with a plan to get things on the right track.The stone stock rpm intake manifold is another issue.
I know from our previous conversations he was on a budget building the truck, so if you are looking for a decent converter for not a lot of money check out Freakshow Performance. I just installed one of their 9.5" converters in my 904 for spray, I paid about $400 shipped, lifetime warranty, free restall whenever you want. I haven't taken it to the track yet, but on the street so far it is nice and tight driving around yet really wakes up when im on it. Hopefully I can get it to the track in the next week or two to see what it does.
Just thought I'd throw the idea out there
|
|
|
Re: Any guesses what this combo may run?
[Re: goldmember]
#1638210
07/01/14 10:42 AM
07/01/14 10:42 AM
|
Joined: Nov 2006
Posts: 733 jacksonville,FLORIDA
slammedR/T
super stock
|
super stock
Joined: Nov 2006
Posts: 733
jacksonville,FLORIDA
|
Quote:
The combo is a 1990 Dakota street truck(approx 3550-3600lbs with driver),3.73's,stockish 727, PTC 9.5" converter that flashed 3800 with the former stock lower end 360 magnum, 750HP holley, 1 5/8" Hooker headers,Edelbrock RPM intake. The new shortblock is 408" with 10.2 to 1 comp, hyd roller 237/245 .585 108lsa in @ 105,Same Magnum R/T heads 2.02/1.6 no flow bench help ,valve springs are 170/395open doubles. Other than increased cubes,slight comp increase,10ish degrees more duration and slight lift(area increase)it's the same as it has been for years. LOL any guesses? Should know some answers Friday nite so.......Why not take a shot??
SLOW! good times bud hope to be back in G'ville racing with you soon homie
2000 Dakota R/T, 408 magnum, 727, Indy heads 1000cfm 4150 carb, 93 octane fuel. motor; 10.258 @ 132.78 200 shot; 9.262 @ 144.69 racemagnum
|
|
|
Re: Any guesses what this combo may run?
[Re: MR_P_BODY]
#1638212
07/01/14 11:40 AM
07/01/14 11:40 AM
|
Joined: Nov 2004
Posts: 3,544 Syracuse,NY
CompWedgeEngines
master
|
master
Joined: Nov 2004
Posts: 3,544
Syracuse,NY
|
Guy here with a Chevy has been thru three of them already...
RIP Monte Smith
Your work is a reflection of yourself, autograph it with quality.
WD for Diamond Pistons,Sidewinder cylinder heads, Wiseco, K1 rods and cranks,BAM lifters, Morel lifters, Molnar Technologies, Harland Sharp, Pro Gear, Cometic, King Engine Bearings and many others.
|
|
|
Re: Any guesses what this combo may run?
[Re: CompWedgeEngines]
#1638213
07/01/14 11:52 AM
07/01/14 11:52 AM
|
Joined: Jun 2003
Posts: 52,972 Romeo MI
MR_P_BODY
Master
|
Master
Joined: Jun 2003
Posts: 52,972
Romeo MI
|
Quote:
Guy here with a Chevy has been thru three of them already...
I guess he is big over on YB... thats where my buddy heard of them... I guess he is going back with PTC for his new one... he has a back up conv so it will going back together today with the back up
|
|
|
|
|