Re: Stroker Hemi combos, ET/power #s
[Re: 408cuda]
#1554951
12/29/13 01:48 PM
12/29/13 01:48 PM
|
Joined: Jan 2003
Posts: 12,218 Benton, IL.
DaveRS23
Special needs idiot
|
Special needs idiot
Joined: Jan 2003
Posts: 12,218
Benton, IL.
|
505" al KB, 10.71 BDS, 246*/256* roller. 640+ RWHP on pump gas. 68 Dart street/strip car.
Master, again and still
|
|
|
Re: Stroker Hemi combos, ET/power #s
[Re: DaveRS23]
#1554952
12/29/13 02:12 PM
12/29/13 02:12 PM
|
Joined: May 2004
Posts: 12,404 Taxes & Virus's R-US, NY
Dragula
I Live Here
|
I Live Here
Joined: May 2004
Posts: 12,404
Taxes & Virus's R-US, NY
|
Well...I detuned my Hemi for reliability and to be legal Nostalgia Mod Gas....Still 11.6:1 compression, still pump gas friendly, 484 cubes, good flowing heads but more room in them yet maybe 20cfm, good size valves, ported intake...It definitly liked the TR better, but I have an SV1 on the way that should wake it up... Made +750hp Injected with a real cam.... Under carburated and with a very mild cam, and less valve spring pressure, its made 665hp so far with an ignition miss, and a crack in the intake...Had the intake welded up and I think I found the ignition miss...Still tuning it though.
|
|
|
Re: Stroker Hemi combos, ET/power #s
[Re: Dragula]
#1554953
12/29/13 03:45 PM
12/29/13 03:45 PM
|
Joined: Jul 2006
Posts: 4,179 California
mickm
master
|
master
Joined: Jul 2006
Posts: 4,179
California
|
not the best picture... 540 c.i. 10.3:1, 248/255 - .605/.588 cam, stage V heads and intake, 2 edelbrock 650's. did 712 at 6k, now using that to tear up the rear tires!
Last edited by mickm; 12/29/13 03:50 PM.
|
|
|
Re: Stroker Hemi combos, ET/power #s
[Re: 408cuda]
#1554954
12/29/13 07:32 PM
12/29/13 07:32 PM
|
Joined: Mar 2006
Posts: 2,675 Mt. Eden Ky.
Hemi Allstate
master
|
master
Joined: Mar 2006
Posts: 2,675
Mt. Eden Ky.
|
I haven't had this one on the dyno, and only a few times down the track. The entire car is a new build and not dialed in. My Hemi is 572" alum. World block, CP 10.5 pistons, Stage V replacement heads CNC @ MCH. Comp solid roller from Dwayne Porter. The carb is a 4150 race Demon RS for now, and that is where I am looking to make changes. I have a 426- 3 and a Rat Roaster X ram to play with in the future. Not pushing the car hard at all, short shifting about 6,000. Have three passes with best of 6.13 @ 113.3 mph. Running pump gas. Mark
1996 Ram 1500 Sport 1968 road runner 1952 Sears Allstate licensed, pump gas, Hemi 5.98 @ 115.73 1.33 60 ft. The best is yet to come. Painless Performance / Street RODDER magazine Top 100 for 2019
|
|
|
Re: Stroker Hemi combos, ET/power #s
[Re: Hemi Allstate]
#1554955
12/29/13 09:20 PM
12/29/13 09:20 PM
|
Joined: Jan 2010
Posts: 311 Kingsville, Md
grncpe
enthusiast
|
enthusiast
Joined: Jan 2010
Posts: 311
Kingsville, Md
|
Mine is 588" 4.5 bore, 4.625 stroke. mopar ported heads, flow 415@800 lift. 760,740 284@.50 roller. 12to1 comp. potrted stage V intake, 2 800 cfm afb's Made 836hp @6700, 730tq @ 5300, My car is all steel,full interior on a 10" tire, & leafs. very nose heavy. so far 1.27 60' 9.53@ 142mph. still not a stellar run.
|
|
|
Re: Stroker Hemi combos, ET/power #s
[Re: 408cuda]
#1554957
12/30/13 08:48 AM
12/30/13 08:48 AM
|
Joined: Jan 2003
Posts: 6,392 nielsville, minn.
quickd100
master
|
master
Joined: Jan 2003
Posts: 6,392
nielsville, minn.
|
605 Hemi, MP block, Indy rotating assembly kit, Indy 426SR heads, Bullet custom solid roller, .767/.676, 288/292, 113 centerline. Weiand tunnelram, 2 850 thermoquads, 12 quart pan,Milodon dual line system. 853hp@5800, 818ftlbs@4800. Performance?, best 60ft was a 1.45 spinning, haven't had a clean full 1/4 pass, last pass bent framerails on launch went into chassis shake and had to drop the throttle just past 1/8 mark, coasted through at 10.74@108. Dave
|
|
|
Re: Stroker Hemi combos, ET/power #s
[Re: grncpe]
#1554959
12/30/13 09:59 AM
12/30/13 09:59 AM
|
Joined: Sep 2005
Posts: 623 Deep DEEP SOUTH
LAD 524
mopar
|
mopar
Joined: Sep 2005
Posts: 623
Deep DEEP SOUTH
|
Quote:
Mine is 588" 4.5 bore, 4.625 stroke. mopar ported heads, flow [Email]415@800[/Email] lift. 760,740 [Email]284@.50[/Email] roller. 12to1 comp. potrted stage V intake, 2 800 cfm afb's Made 836hp @6700, 730tq @ 5300, My car is all steel,full interior on a 10" tire, & leafs. very nose heavy. so far 1.27 60' 9.53@ 142mph. still not a stellar run. [url=http://s823.photobucket.com/user/FabBakers/media/DSC01727_zps487fa57b.jpg.html]
Now thats tuff !
Here's mine - will be in at around 3500lbs. Made 845HP/770TQ, I hope I can go as fast as you have
Hemi mega block 4.5" bore - o-ringed 4.5" Bryant crank Saenz 7.1" rods 11:1 Diamond pistons - coated tops/skirts Sealed Power rings ARP rod, crank, head studs, oil pan studs, flywheel bolts Bullet roller 752/684" lift 270/280 @ .050" 112 & Isky Red Zone Xtreme EZ roller lifters Indy Legend heads ported 420 cfm Stage V rollers MSD dist/box/crank trigger Indy 426-4 4500 intake/have a 4500 Barton intake as well Pro systems 1150 Electric water pump Milodon ext dual line swinging pickup and pump 727 with all the good gear Ultimate Convertor 9" 4.11s
Last edited by ratbastad; 12/30/13 10:08 AM.
|
|
|
Re: Stroker Hemi combos, ET/power #s
[Re: 408cuda]
#1554960
12/30/13 05:27 PM
12/30/13 05:27 PM
|
Joined: Jul 2006
Posts: 4,179 California
mickm
master
|
master
Joined: Jul 2006
Posts: 4,179
California
|
Quote:
Awesome iron. Some quality hot rods for sure.
My build is much like Mickm, 520-540ish Stage V street/strip 4 speed.
Have you had yours to the strip at all Mick?
Thanks guys, keep em coming. Winter here is looong!
no, haven't made it yet. dealing with a bunch of issues, most notably an ignition system that either misses badly near the rev limit, or has no rev limit.
hopefully this spring/summer.
|
|
|
Re: Stroker Hemi combos, ET/power #s
[Re: quickd100]
#1554961
12/30/13 05:35 PM
12/30/13 05:35 PM
|
Joined: Jul 2004
Posts: 19,318 State of confusion
Thumperdart
I Live Here
|
I Live Here
Joined: Jul 2004
Posts: 19,318
State of confusion
|
Quote:
605 Hemi, MP block, Indy rotating assembly kit, Indy 426SR heads, Bullet custom solid roller, .767/.676, 288/292, 113 centerline. Weiand tunnelram, 2 850 thermoquads, 12 quart pan,Milodon dual line system. [Email]853hp@5800[/Email], [Email]818ftlbs@4800.[/Email] Performance?, best 60ft was a 1.45 spinning, haven't had a clean full 1/4 pass, last pass bent framerails on launch went into chassis shake and had to drop the throttle just past 1/8 mark, coasted through at [Email]10.74@108.[/Email] Dave
This is too cool right there..............hopefully you can get the damage fixed and get some full passes............I see a feature show here w/the 405 boys.............You vs Farmtruck.........
72 Dart 470 n/a BB stroker street car `THUMPER`...Check me out on FB Dominic Thumper for videos and lots of carb pics......760-900-3895.....
|
|
|
Re: Stroker Hemi combos, ET/power #s
[Re: grncpe]
#1554962
12/30/13 05:50 PM
12/30/13 05:50 PM
|
Joined: Dec 2012
Posts: 1,824 Wind Gap,Pa.
Sammy
top fuel
|
top fuel
Joined: Dec 2012
Posts: 1,824
Wind Gap,Pa.
|
Quote:
Mine is 588" 4.5 bore, 4.625 stroke. mopar ported heads, flow [Email]415@800[/Email] lift. 760,740 [Email]284@.50[/Email] roller. 12to1 comp. potrted stage V intake, 2 800 cfm afb's Made 836hp @6700, 730tq @ 5300, My car is all steel,full interior on a 10" tire, & leafs. very nose heavy. so far 1.27 60' 9.53@ 142mph. still not a stellar run.
[url=http://s823.photobucket.com/user/FabBakers/media/airtime1_zps4c628866.jpg.html][image]http://i823.photobucket.com/albums/zz160/FabBakers/airtime1_zps4c628866.jp
g[/image][/url]
I'm demanding more pictures of this beautiful cuda
|
|
|
Re: Stroker Hemi combos, ET/power #s
[Re: Sammy]
#1554963
12/30/13 06:53 PM
12/30/13 06:53 PM
|
Joined: Aug 2010
Posts: 167 mi
dirty magnum
member
|
member
Joined: Aug 2010
Posts: 167
mi
|
Quote:
Quote:
Mine is 588" 4.5 bore, 4.625 stroke. mopar ported heads, flow [Email]415@800[/Email] lift. 760,740 [Email]284@.50[/Email] roller. 12to1 comp. potrted stage V intake, 2 800 cfm afb's Made 836hp @6700, 730tq @ 5300, My car is all steel,full interior on a 10" tire, & leafs. very nose heavy. so far 1.27 60' 9.53@ 142mph. still not a stellar run.
[url=http://s823.photobucket.com/user/FabBakers/media/airtime1_zps4c628866.jpg.html][image]http://i823.photobucket.com/albums/zz160/FabBakers/airtime1_zps4c628866.jp
g[/image][/url]
I'm demanding more pictures of this beautiful cuda
x2
|
|
|
Re: Stroker Hemi combos, ET/power #s
[Re: dirty magnum]
#1554964
12/30/13 07:04 PM
12/30/13 07:04 PM
|
Joined: Jan 2007
Posts: 2,431 SK,Canada
gregsrt
top fuel
|
top fuel
Joined: Jan 2007
Posts: 2,431
SK,Canada
|
Quote:
Quote:
Quote:
Mine is 588" 4.5 bore, 4.625 stroke. mopar ported heads, flow [Email]415@800[/Email] lift. 760,740 [Email]284@.50[/Email] roller. 12to1 comp. potrted stage V intake, 2 800 cfm afb's Made 836hp @6700, 730tq @ 5300, My car is all steel,full interior on a 10" tire, & leafs. very nose heavy. so far 1.27 60' 9.53@ 142mph. still not a stellar run.
[url=http://s823.photobucket.com/user/FabBakers/media/airtime1_zps4c628866.jpg.html][image]http://i823.photobucket.com/albums/zz160/FabBakers/airtime1_zps4c628866.jp
g[/image][/url]
I'm demanding more pictures of this beautiful cuda
x2
I had to right click/save when he posted pics of it a while ago. It is nice
An association of men who will not quarrel with one another is a thing which has never yet existed, from the greatest confederacy of nations down to a town meeting or a vestry.
Thomas Jefferson
|
|
|
Re: Stroker Hemi combos, ET/power #s
[Re: grncpe]
#1554966
12/30/13 11:11 PM
12/30/13 11:11 PM
|
Joined: Dec 2012
Posts: 1,824 Wind Gap,Pa.
Sammy
top fuel
|
top fuel
Joined: Dec 2012
Posts: 1,824
Wind Gap,Pa.
|
Quote:
Sure!
I only have a few on photobucket... There was a thread on here while I was building it. I think it was SS/DA progress.... Thanks for asking
beautiful fish! Come on an tease me some more. Awesome is an understatement.
|
|
|
|
|