Shortening 8 3/4" without a jig (use channel iron & clamps)

Print Thread

Re: Shortening 8 3/4" without a jig (use channel iron & clamps) [Re: jcc] #3200132 12/26/23 06:57 PM 12/26/23 06:57 PM
Joined: Jan 2003 Posts: 20,210 Park Forest, IL slantzilla Too Many Posts
slantzilla Too Many Posts Joined: Jan 2003 Posts: 20,210 Park Forest, IL	I used to work in a shop that did a lot of rear shortening and/or straightening. They had the Mittler Brothers setup which is the spacers and bar. 8.8 Fords were the worst for being crap from the factory. "Everybody funny, now you funny too."

Entire Thread
Subject	Posted By	Posted
Shortening 8 3/4" without a jig (use channel iron & clamps)	VITC_GTX	12/20/23 04:56 AM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	2boltmain	12/20/23 10:44 AM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	dvw	12/20/23 02:17 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	B1Frank	12/20/23 04:03 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	John_Kunkel	12/20/23 06:42 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	440_Offroader	12/22/23 02:45 AM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	dvw	12/25/23 04:23 AM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	John_Kunkel	12/25/23 05:21 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	jcc	12/26/23 10:38 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	A727Tflite	12/26/23 10:56 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	jcc	12/27/23 02:12 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	slantzilla	12/26/23 10:57 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	TJP	12/27/23 02:53 AM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	IMGTX	12/27/23 02:28 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	John_Kunkel	12/27/23 07:40 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	IMGTX	12/22/23 03:06 AM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	markz528	12/22/23 03:23 AM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	GY3	12/22/23 01:59 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	VITC_GTX	12/24/23 11:22 PM

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To