Shortening 8 3/4" without a jig (use channel iron & clamps)

Print Thread

Re: Shortening 8 3/4" without a jig (use channel iron & clamps) [Re: John_Kunkel] #3200130 12/26/23 06:38 PM 12/26/23 06:38 PM
Joined: Dec 2003 Posts: 22,727 Bitopia J jcc If you can't dazzle em with diamonds..
jcc If you can't dazzle em with diamonds.. J Joined: Dec 2003 Posts: 22,727 Bitopia	I used a 1.25" ground SS bar fore my setup Reality check, that half the population is smarter then 50% of the people and it's a constantly contested fact.

Entire Thread
Subject	Posted By	Posted
Shortening 8 3/4" without a jig (use channel iron & clamps)	VITC_GTX	12/20/23 04:56 AM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	2boltmain	12/20/23 10:44 AM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	dvw	12/20/23 02:17 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	B1Frank	12/20/23 04:03 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	John_Kunkel	12/20/23 06:42 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	440_Offroader	12/22/23 02:45 AM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	dvw	12/25/23 04:23 AM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	John_Kunkel	12/25/23 05:21 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	jcc	12/26/23 10:38 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	A727Tflite	12/26/23 10:56 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	jcc	12/27/23 02:12 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	slantzilla	12/26/23 10:57 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	TJP	12/27/23 02:53 AM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	IMGTX	12/27/23 02:28 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	John_Kunkel	12/27/23 07:40 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	IMGTX	12/22/23 03:06 AM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	markz528	12/22/23 03:23 AM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	GY3	12/22/23 01:59 PM
Re: Shortening 8 3/4" without a jig (use channel iron & clamps)	VITC_GTX	12/24/23 11:22 PM

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To