Crane Cam F-288/4134-6 - Moparts Forums

Register Log In Moparts Forums Unlawfl's Race & Engine Tech Crane Cam F-288/4134-6

Print Thread

Re: Crane Cam F-288/4134-6 [Re: pittsburghracer] #3046239 05/29/22 07:21 PM 05/29/22 07:21 PM
Joined: Sep 2007 Posts: 427 Cascade, CO reknapp52 OP mopar
reknapp52 OP mopar Joined: Sep 2007 Posts: 427 Cascade, CO	That's the info I'm using, this gives a numerical center of the profile of 102 degrees. The center of the tip top of the intake lobe will be at 96 degrees. Unless I'm all messed up?

Entire Thread
Subject	Posted By	Posted
Crane Cam F-288/4134-6	reknapp52	05/29/22 08:33 PM
Re: Crane Cam F-288/4134-6	pittsburghracer	05/29/22 09:07 PM
Re: Crane Cam F-288/4134-6	reknapp52	05/29/22 11:21 PM
Re: Crane Cam F-288/4134-6	AndyF	05/29/22 11:43 PM
Re: Crane Cam F-288/4134-6	reknapp52	05/30/22 03:50 AM
Re: Crane Cam F-288/4134-6	Cab_Burge	05/30/22 05:29 AM
Re: Crane Cam F-288/4134-6	rb446	05/30/22 09:52 AM
Re: Crane Cam F-288/4134-6	Cab_Burge	05/30/22 06:35 PM
Re: Crane Cam F-288/4134-6	pittsburghracer	05/30/22 06:41 PM
Re: Crane Cam F-288/4134-6	Cab_Burge	05/30/22 06:45 PM
Re: Crane Cam F-288/4134-6	reknapp52	05/30/22 07:12 PM
Re: Crane Cam F-288/4134-6	Cab_Burge	05/30/22 08:30 PM
Re: Crane Cam F-288/4134-6	reknapp52	05/30/22 09:23 PM
Re: Crane Cam F-288/4134-6	fast68plymouth	05/30/22 09:47 PM
Re: Crane Cam F-288/4134-6	AndyF	05/30/22 10:38 PM
Re: Crane Cam F-288/4134-6	reknapp52	05/31/22 05:12 AM
Re: Crane Cam F-288/4134-6	DrCharles	06/01/22 03:23 AM
Re: Crane Cam F-288/4134-6	reknapp52	06/01/22 04:26 AM
Re: Crane Cam F-288/4134-6	fast68plymouth	06/01/22 03:09 PM
Re: Crane Cam F-288/4134-6	reknapp52	06/01/22 07:06 PM
Re: Crane Cam F-288/4134-6	HardcoreB	06/06/22 01:08 PM
Re: Crane Cam F-288/4134-6	reknapp52	06/06/22 08:17 PM
Re: Crane Cam F-288/4134-6	fast68plymouth	06/06/22 08:35 PM

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1