What 727 1350 yoke to use?
#962415
03/30/11 01:55 PM
03/30/11 01:55 PM
|
Joined: Jan 2004
Posts: 2,103 East Coast, NJ
fig426
OP
top fuel
|
OP
top fuel
Joined: Jan 2004
Posts: 2,103
East Coast, NJ
|
I'm finally almost done getting the hemi Challenger together. I'll finish the rear next week and it will be time for a driveshaft. I'm estimating 600hp with a 4:30 gear. 29/12 tire. 3800lb foot brake. I need to get a 1350 yoke. I had ordered one from Jegs but it was cast and I was concerned. I built the car to HOPEFULLY not break. Who sells forged or billet yokes? Or is it not necessary for this car?
Chris from New Jersey
|
|
|
Re: What 727 1350 yoke to use?
[Re: Randy..]
#962418
03/30/11 04:58 PM
03/30/11 04:58 PM
|
Joined: Mar 2009
Posts: 1,058 bigfork mn
dragram440
super stock
|
super stock
Joined: Mar 2009
Posts: 1,058
bigfork mn
|
I got mine from Dr. diff Good price Good service!!
Last edited by dragram440; 03/31/11 01:33 PM.
67' charger 499 RB
10.57 at 127
|
|
|
Re: What 727 1350 yoke to use?
[Re: fishy340]
#962421
03/30/11 08:30 PM
03/30/11 08:30 PM
|
Joined: Jun 2010
Posts: 3,112 LONG ISLAND
fishy340
master
|
master
Joined: Jun 2010
Posts: 3,112
LONG ISLAND
|
Quote:
moser its in jegs or summit
just make sure when u order it u look at the spline on the tranny theres a 10spline and i forget the other its like 29 or so
|
|
|
Re: What 727 1350 yoke to use?
[Re: fig426]
#962423
03/31/11 08:30 AM
03/31/11 08:30 AM
|
Anonymous
Unregistered
|
Anonymous
Unregistered
|
Well after the yoke failure i had. I'll only use MARK WILLIAMS.
|
|
|
Re: What 727 1350 yoke to use?
#962424
03/31/11 08:33 AM
03/31/11 08:33 AM
|
Joined: Jan 2003
Posts: 13,374 Marion, South Carolina [><]
an8sec70cuda
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 13,374
Marion, South Carolina [><]
|
How much power will the cheaper cast units handle? I have a Mark Williams yoke in the cuda, been there for the last 8 years or so w/ no problems. I need one for my road runner and was looking at the cast pieces...
CHIP '70 hemicuda, 575" Hemi, 727, Dana 60 '69 road runner, 440-6, 18 spline 4 speed, Dana 60 '71 Demon, 340, low gear 904, 8.75 '73 Chrysler New Yorker, 440, 727, 8.75 '90 Chevy 454SS Silverado, 476" BBC, TH400, 14 bolt '06 GMC 2500HD LBZ Duramax
|
|
|
Re: What 727 1350 yoke to use?
[Re: DoctorDiff]
#962428
03/31/11 01:31 PM
03/31/11 01:31 PM
|
Joined: Mar 2009
Posts: 1,058 bigfork mn
dragram440
super stock
|
super stock
Joined: Mar 2009
Posts: 1,058
bigfork mn
|
I believe mine is a spicer also. My car weighs 3800 lbs and runs 10.60's with the foot brake. Think this is a strong enough pieces for me?
67' charger 499 RB
10.57 at 127
|
|
|
Re: What 727 1350 yoke to use?
[Re: DoctorDiff]
#962430
03/31/11 09:05 PM
03/31/11 09:05 PM
|
Joined: Dec 2004
Posts: 10,555 Rittman Ohio
fourgearsavoy
I Live Here
|
I Live Here
Joined: Dec 2004
Posts: 10,555
Rittman Ohio
|
I use a Spicer 1350 yoke on my shaft and I find it hard to believe that an average bracket car can break one My car weighs 3600# with a stickshift and the drive shaft is on my list of things I don't worry about breaking. Gus
64 Plymouth Savoy 493 Indy EZ's by Nick at Compu-Flow 5-Speed Richmond faceplate Liberty box Dana 60
|
|
|
|
|