Moparts

What 727 1350 yoke to use?

Posted By: fig426

What 727 1350 yoke to use? - 03/30/11 05:55 PM

I'm finally almost done getting the hemi Challenger together. I'll finish the rear next week and it will be time for a driveshaft. I'm estimating 600hp with a 4:30 gear. 29/12 tire. 3800lb foot brake. I need to get a 1350 yoke. I had ordered one from Jegs but it was cast and I was concerned. I built the car to HOPEFULLY not break. Who sells forged or billet yokes? Or is it not necessary for this car?

Attached picture 6557857-3721402-ChallengerHemi1.jpg
Posted By: 1967dartgt

Re: What 727 1350 yoke to use? - 03/30/11 06:29 PM

Mark Williams
Posted By: Randy..

Re: What 727 1350 yoke to use? - 03/30/11 06:33 PM

Strange say ther forged is good for 800hp, anything more use a Billet yoke.
Posted By: dragram440

Re: What 727 1350 yoke to use? - 03/30/11 08:58 PM

I got mine from Dr. diff Good price Good service!!
Posted By: JD Dart

Re: What 727 1350 yoke to use? - 03/31/11 12:26 AM

Mark Williams
Posted By: fishy340

Re: What 727 1350 yoke to use? - 03/31/11 12:28 AM

moser its in jegs or summit
Posted By: fishy340

Re: What 727 1350 yoke to use? - 03/31/11 12:30 AM

Quote:

moser its in jegs or summit

just make sure when u order it u look at the spline on the tranny theres a 10spline and i forget the other its like 29 or so
Posted By: fig426

Re: What 727 1350 yoke to use? - 03/31/11 12:09 PM

Quote:

moser its in jegs or summit


The Moser they carry is a cast unit.
Posted By: Anonymous

Re: What 727 1350 yoke to use? - 03/31/11 12:30 PM

Well after the yoke failure i had. I'll only use MARK WILLIAMS.
Posted By: an8sec70cuda

Re: What 727 1350 yoke to use? - 03/31/11 12:33 PM

How much power will the cheaper cast units handle? I have a Mark Williams yoke in the cuda, been there for the last 8 years or so w/ no problems. I need one for my road runner and was looking at the cast pieces...
Posted By: Mpetros

Re: What 727 1350 yoke to use? - 03/31/11 02:26 PM

Spicer 3-3-3931x
Posted By: j.mcconnell

Re: What 727 1350 yoke to use? - 03/31/11 03:27 PM

I just pick up one of these:
http://cgi.ebay.com/ebaymotors/SB-BB-Chr...sQ5fAccessories

Forged Spicer yoke. Fast and free shipping.
Posted By: DoctorDiff

Re: What 727 1350 yoke to use? - 03/31/11 04:08 PM

Spicer yokes are cast, not forged. Note, the narrow parting line.
Posted By: dragram440

Re: What 727 1350 yoke to use? - 03/31/11 05:31 PM

I believe mine is a spicer also. My car weighs 3800 lbs and runs 10.60's with the foot brake. Think this is a strong enough pieces for me?
Posted By: DoctorDiff

Re: What 727 1350 yoke to use? - 04/01/11 12:23 AM

Yes, the cast Spicer yokes are still a stout piece.
Posted By: fourgearsavoy

Re: What 727 1350 yoke to use? - 04/01/11 01:05 AM

I use a Spicer 1350 yoke on my shaft and I find it hard to believe that an average bracket car can break one My car weighs 3600# with a stickshift and the drive shaft is on my list of things I don't worry about breaking.
Gus

Attached picture 6561021-burnoutpicturegus.JPG
Posted By: 74_360_Cuda

Re: What 727 1350 yoke to use? - 05/10/11 02:07 AM

Quote:

Yes, the cast Spicer yokes are still a stout piece.



Dr Diff, do you sell billet or forged yokes for 727 7290?

If not, What about this one from Inland Empire available at Summit

http://www.summitracing.com/parts/IED-SY7277290/
Posted By: Voluster

Re: What 727 1350 yoke to use? - 05/10/11 03:51 AM

The cast ones work fine

I have the cast one on the front and the rear of my DS both 1350

I went 1.36 at 3480 last weekend
Posted By: 74_360_Cuda

Re: What 727 1350 yoke to use? - 05/10/11 04:17 AM

Thanks,good info but I need to buy one anyway (I am upgrading from 7260 to 7290) and the price differance is vey small so I think it would be a cheap insurance...
Posted By: rowin4

Re: What 727 1350 yoke to use? - 05/10/11 04:36 AM

I've twisted the cast Spicer 1350 yoke splines to the point I had to beat the yoke off the transmission with a BFH, I did replace it with the same, there a beefy yoke but billet is best.

Posted By: DoctorDiff

Re: What 727 1350 yoke to use? - 05/10/11 03:30 PM

Unfortunately, I don't know of a source for forged 7290 727 slip yokes. I can only get the cast versions like the one in your link.

If you are changing the driveshaft, I recommend upgrading to a 1350 unit. Forged slip yokes are readily available.
Posted By: fury62

Re: What 727 1350 yoke to use? - 05/11/11 12:45 AM

strange chrome-moly 1350 slip yoke
Posted By: 74_360_Cuda

Re: What 727 1350 yoke to use? - 05/11/11 01:34 AM

Quote:

I can only get the cast versions like the one in your link.



The one in my link says steel so I assume it is billet? (The price would match also)
© 2024 Moparts Forums