Which section do I ask about rust repairs?
#934986
02/22/11 04:59 PM
02/22/11 04:59 PM
|
Joined: Jan 2004
Posts: 289 Toronto, ON
ehbody
OP
enthusiast
|
OP
enthusiast
Joined: Jan 2004
Posts: 289
Toronto, ON
|
I got a fender that is rust free. BUT it seems to have been dragged down a pillar/wall. Creased and filled with bondo. Should I remove the bondo, fix first or get dipped/striped first then fix. Anywhere that can dip/Strip a fender and two doors cheap, cheap, cheap in Toronto, ON? It will be me attempting to straighten the fender, without mud.
Shawn
70 AAR
|
|
|
Re: Which section do I ask about rust repairs?
[Re: ehbody]
#934988
02/23/11 11:31 AM
02/23/11 11:31 AM
|
Joined: Nov 2005
Posts: 15,119 85086
moparpollack
Lil Herman
|
Lil Herman
Joined: Nov 2005
Posts: 15,119
85086
|
Quote:
I got a fender that is rust free. BUT it seems to have been dragged down a pillar/wall. Creased and filled with bondo. Should I remove the bondo, fix first or get dipped/striped first then fix.
Anywhere that can dip/Strip a fender and two doors cheap, cheap, cheap in Toronto, ON?
It will be me attempting to straighten the fender, without mud.
Mud is a fact of life why avoid it? The dents should be taken out before mudding but there will be some mud.
Do a search for bodywork techniques than see what you have for tools and make the decision if you want to do it yourself or pay to have it done.
56 Plaza 63 D100 step side 67 Coronet, 68 Roadrunner, 69 Super Bees, 69 Coronet 500 convertible, 70 Roadrunner Post, 79 D150 360, and a severe case of Mopar a,d,d
|
|
|
Re: Which section do I ask about rust repairs?
[Re: moparpollack]
#934989
02/23/11 01:04 PM
02/23/11 01:04 PM
|
Joined: Oct 2003
Posts: 21,345 Marysville, O-H-I-O
70Cuda383
Too Many Posts
|
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
I agree, you have to use filler over metal work, however, it sounds like this has deep creases/dents that were filled with a half inch thick smear of bondo?
if so, yes, definitely remove the filler and work the metal a little bit, but in the end, you will have to have a skim coat of bondo and block sand it out. maybe 1/8" thick at the most is all you'll need if you do the hammer and dolly work correctly.
**Photobucket sucks**
|
|
|
Re: Which section do I ask about rust repairs?
[Re: 70Cuda383]
#934990
02/23/11 04:38 PM
02/23/11 04:38 PM
|
Joined: Jan 2004
Posts: 289 Toronto, ON
ehbody
OP
enthusiast
|
OP
enthusiast
Joined: Jan 2004
Posts: 289
Toronto, ON
|
Thanks. I am attempting the Fairmount Method. I have had basic attempts before on cars, but did indeed use metal based bondo. It was a spitfire bonnet headlamp area, that overwhelmed my ability, But I was able to create a compond curve patch for the valance that required only spot putty, using English wheel. I am assuming that my 70's parts are thick enough for this, As the book I am referencing was published in 1953, Bondo was then just a new product. Plus I have my Dad who is of that time. Except he likes bondo. I know this will be time consuming. Hammer On, Hammer Off, Paint On, Wax On, Wax Off.
Shawn
70 AAR
|
|
|
|
|