|
Re: New 5.7 hemi eagle head
[Re: RTSrunner]
#934457
04/04/11 10:14 AM
04/04/11 10:14 AM
|
Joined: Jun 2005
Posts: 2,776
Ontario Canada
MattW
OP
master
|
OP
master
Joined: Jun 2005
Posts: 2,776
Ontario Canada
|
Quote:
Quote:
got this on the net." now for the useful stuff.
Cylinder heads. big changes here, new closed chamber heads have smaller chambers (duh) than previous engines , 66.3cc in fact vs 84.9cc. even smaller than the 6.1's with 73.0cc. bolting these on to a previous hemi without modification would result in nearly a 12:1 compression ratio.
Are there pistons available to get a lower compression ratio than 12:1 using these heads on an earlier engine?I assume the stock later piston would work,not sure what CR is on late hemis though.
RT
Well there is always custom. I am not sure of the 09 piston but I think they would work. I think 09 got a compression boost. Matt
|
|
|
Re: New 5.7 hemi eagle head
[Re: MattW]
#934458
04/04/11 10:34 AM
04/04/11 10:34 AM
|
Joined: Sep 2004
Posts: 1,828
houston texas
gremlinsteve
top fuel
|
top fuel
Joined: Sep 2004
Posts: 1,828
houston texas
|
yes. use like a wiseco 9.0 to one piston or a diamond 8.5 that will get you into the 10.0-10.5 range with that head. i know the wiseco is more of a shelf stock piston
steve
if You Like Gremlinsteve. Gremlinsteve Likes You.
|
|
|
Re: New 5.7 hemi eagle head
[Re: gremlinsteve]
#934459
04/04/11 11:40 AM
04/04/11 11:40 AM
|
Joined: Jun 2005
Posts: 2,776
Ontario Canada
MattW
OP
master
|
OP
master
Joined: Jun 2005
Posts: 2,776
Ontario Canada
|
Quote:
yes. use like a wiseco 9.0 to one piston or a diamond 8.5 that will get you into the 10.0-10.5 range with that head. i know the wiseco is more of a shelf stock piston
steve
Good to know. 
|
|
|
Re: New 5.7 hemi eagle head
[Re: Challenger]
#934464
06/03/11 07:44 AM
06/03/11 07:44 AM
|
Joined: Jun 2005
Posts: 2,776
Ontario Canada
MattW
OP
master
|
OP
master
Joined: Jun 2005
Posts: 2,776
Ontario Canada
|
Quote:
Alright Im just a little confused on these part numbers for the Eagle head. I worked on a 07 truck with a 5.7 hemi and the part numbers on them heads were 53021608de and 53021609de which is what was said at the beginning of the post as Eagle heads BUT I didnt think that they were built til 09. So when I go to the dealer what part number should I be telling them for the Eagle heads? Sixpackgut what part numbers are yours? THANKS!
The part# is correct for the eagle head. 53021608DE and 609DE.
You either have made a mistake in identifying the heads or someone has already changed them. Go and see if your heads look like the ones on page 5.
Easiest way to tell D shaped exhaust. Matt
|
|
|
Re: New 5.7 hemi eagle head
[Re: Challenger]
#934466
06/03/11 09:27 AM
06/03/11 09:27 AM
|
Joined: Jun 2003
Posts: 9,225
Charleston
sixpackgut
Drag Week Mod Champion
|
Drag Week Mod Champion
Joined: Jun 2003
Posts: 9,225
Charleston
|
Quote:
Alright Im just a little confused on these part numbers for the Eagle head. I worked on a 07 truck with a 5.7 hemi and the part numbers on them heads were 53021608de and 53021609de which is what was said at the beginning of the post as Eagle heads BUT I didnt think that they were built til 09. So when I go to the dealer what part number should I be telling them for the Eagle heads? Sixpackgut what part numbers are yours? THANKS!
i will have to check when i get home but i think the letters are different than those. but the numbers are the same, even the same as my 04 heads. but when i bought mine i used the part numbers listed in this thread
BTW, i just picked up a 426 for less than a rotating assembly. K1 crank and rods with JE pistons
Last edited by sixpackgut; 06/03/11 09:29 AM.
Gen 3 power 6.22@110, 9.85@135
Follow @g3hemiswap on instagram
performance only racing, CRT, ultimate converter, superior design concepts, ThumperCarbs
|
|
|
Re: New 5.7 hemi eagle head
[Re: sixpackgut]
#934470
06/03/11 02:29 PM
06/03/11 02:29 PM
|
Joined: Jun 2005
Posts: 2,776
Ontario Canada
MattW
OP
master
|
OP
master
Joined: Jun 2005
Posts: 2,776
Ontario Canada
|
Quote:
Quote:
Alright Im just a little confused on these part numbers for the Eagle head. I worked on a 07 truck with a 5.7 hemi and the part numbers on them heads were 53021608de and 53021609de which is what was said at the beginning of the post as Eagle heads BUT I didnt think that they were built til 09. So when I go to the dealer what part number should I be telling them for the Eagle heads? Sixpackgut what part numbers are yours? THANKS!
i will have to check when i get home but i think the letters are different than those. but the numbers are the same, even the same as my 04 heads. but when i bought mine i used the part numbers listed in this thread
BTW, i just picked up a 426 for less than a rotating assembly. K1 crank and rods with JE pistons
Nice find did you see that the eagle head is going for 118.80 a piece. Matt
|
|
|
Re: New 5.7 hemi eagle head
[Re: MattW]
#934471
06/03/11 04:56 PM
06/03/11 04:56 PM
|
Joined: Apr 2007
Posts: 2,826
NY usa
540challenger
master
|
master
Joined: Apr 2007
Posts: 2,826
NY usa
|
Quote:
Quote:
Quote:
Alright Im just a little confused on these part numbers for the Eagle head. I worked on a 07 truck with a 5.7 hemi and the part numbers on them heads were 53021608de and 53021609de which is what was said at the beginning of the post as Eagle heads BUT I didnt think that they were built til 09. So when I go to the dealer what part number should I be telling them for the Eagle heads? Sixpackgut what part numbers are yours? THANKS!
i will have to check when i get home but i think the letters are different than those. but the numbers are the same, even the same as my 04 heads. but when i bought mine i used the part numbers listed in this thread
BTW, i just picked up a 426 for less than a rotating assembly. K1 crank and rods with JE pistons
Nice find did you see that the eagle head is going for 118.80 a piece. Matt
Where??? and is it fully assembled like th Moapr ones with plugs and all??
|
|
|
Re: New 5.7 hemi eagle head
[Re: Challenger]
#934472
06/03/11 06:04 PM
06/03/11 06:04 PM
|
Joined: May 2005
Posts: 221
Missouri
Challenger
enthusiast
|
enthusiast
Joined: May 2005
Posts: 221
Missouri
|
Quote:
. Also the numbers have superceded to 53021608BL and 53021609BL.
Sorry about that the numbers have been superceded to RL021608DE, RL021609DE. Not the above.
BTW Where are you finding them for $118, my cost on them is $248.
|
|
|
Re: New 5.7 hemi eagle head
[Re: Challenger]
#934473
06/03/11 10:04 PM
06/03/11 10:04 PM
|
Joined: Jun 2005
Posts: 2,776
Ontario Canada
MattW
OP
master
|
OP
master
Joined: Jun 2005
Posts: 2,776
Ontario Canada
|
Quote:
Quote:
. Also the numbers have superceded to 53021608BL and 53021609BL.
Sorry about that the numbers have been superceded to RL021608DE, RL021609DE. Not the above.
BTW Where are you finding them for $118, my cost on them is $248.
Go to dodgeparts.com.
Remember if you order from them you will have to pay shipping. Dealer you do not. Matt
|
|
|
Re: New 5.7 hemi eagle head
[Re: MattW]
#934474
06/03/11 10:51 PM
06/03/11 10:51 PM
|
Joined: Jun 2003
Posts: 9,225
Charleston
sixpackgut
Drag Week Mod Champion
|
Drag Week Mod Champion
Joined: Jun 2003
Posts: 9,225
Charleston
|
Quote:
Quote:
Quote:
Alright Im just a little confused on these part numbers for the Eagle head. I worked on a 07 truck with a 5.7 hemi and the part numbers on them heads were 53021608de and 53021609de which is what was said at the beginning of the post as Eagle heads BUT I didnt think that they were built til 09. So when I go to the dealer what part number should I be telling them for the Eagle heads? Sixpackgut what part numbers are yours? THANKS!
i will have to check when i get home but i think the letters are different than those. but the numbers are the same, even the same as my 04 heads. but when i bought mine i used the part numbers listed in this thread
BTW, i just picked up a 426 for less than a rotating assembly. K1 crank and rods with JE pistons
Nice find did you see that the eagle head is going for 118.80 a piece. Matt
ya, i read that. piss me off, i paid almost 90% more  i was going to buy several sets at $222, glad i didnt. does dodge parts have the drag pack intake? i havnt even went over to look
FYI, my heads end in DD. why? i dont have a clue
Gen 3 power 6.22@110, 9.85@135
Follow @g3hemiswap on instagram
performance only racing, CRT, ultimate converter, superior design concepts, ThumperCarbs
|
|
|
Re: New 5.7 hemi eagle head
[Re: sixpackgut]
#934475
06/04/11 09:30 AM
06/04/11 09:30 AM
|
Joined: Jun 2005
Posts: 2,776
Ontario Canada
MattW
OP
master
|
OP
master
Joined: Jun 2005
Posts: 2,776
Ontario Canada
|
Quote:
Quote:
Quote:
Quote:
Alright Im just a little confused on these part numbers for the Eagle head. I worked on a 07 truck with a 5.7 hemi and the part numbers on them heads were 53021608de and 53021609de which is what was said at the beginning of the post as Eagle heads BUT I didnt think that they were built til 09. So when I go to the dealer what part number should I be telling them for the Eagle heads? Sixpackgut what part numbers are yours? THANKS!
i will have to check when i get home but i think the letters are different than those. but the numbers are the same, even the same as my 04 heads. but when i bought mine i used the part numbers listed in this thread
BTW, i just picked up a 426 for less than a rotating assembly. K1 crank and rods with JE pistons
Nice find did you see that the eagle head is going for 118.80 a piece. Matt
ya, i read that. piss me off, i paid almost 90% more i was going to buy several sets at $222, glad i didnt. does dodge parts have the drag pack intake? i havnt even went over to look
FYI, my heads end in DD. why? i dont have a clue
It's OK. I payed 248 a piece. But I did not have to pay for shipping.
Don't bother with dodge parts for the intake it's 1114.30
You can try MonicattyChrysler 747.00
You may have a hard time with availability
As to why your heads end in DD
|
|
|
|
|
