Milodon 30931 Oil Pan - Moparts Forums

Register Log In Moparts Forums Unlawfl's Race & Engine Tech Milodon 30931 Oil Pan

Print Thread

Milodon 30931 Oil Pan #471915 09/18/09 05:05 PM 09/18/09 05:05 PM
Joined: Feb 2007 Posts: 6,295 U.S. M moparniac OP master
moparniac OP master M Joined: Feb 2007 Posts: 6,295 U.S.	Do any of you guys runs this pan on a BB Stroker A Body car..... says is good for only 3.750 stroke.... says no dipstick provision either what about a windage tray also.... thx http://www.summitracing.com/parts/MIL-30931/?image=large Last edited by WeDgiE; 09/18/09 05:09 PM. Mopar Performance

Re: Milodon 30931 Oil Pan [Re: moparniac] #471916 09/18/09 05:58 PM 09/18/09 05:58 PM
Joined: Oct 2004 Posts: 5,618 long island NY A Ari440 master
Ari440 master A Joined: Oct 2004 Posts: 5,618 long island NY	1.39 9.85 - 137 mph

Re: Milodon 30931 Oil Pan [Re: Ari440] #471917 09/18/09 05:59 PM 09/18/09 05:59 PM
Joined: Oct 2004 Posts: 5,618 long island NY A Ari440 master
Ari440 master A Joined: Oct 2004 Posts: 5,618 long island NY	1.39 9.85 - 137 mph

Re: Milodon 30931 Oil Pan [Re: Ari440] #471918 09/18/09 06:05 PM 09/18/09 06:05 PM
Joined: Feb 2007 Posts: 6,295 U.S. M moparniac OP master
moparniac OP master M Joined: Feb 2007 Posts: 6,295 U.S.	ARI dont you have a stroker motor? directions say maximum stroke of 3.750 ? also do you run a windage tray? thx Mopar Performance

Re: Milodon 30931 Oil Pan [Re: moparniac] #471919 09/18/09 06:17 PM 09/18/09 06:17 PM
Joined: Oct 2004 Posts: 5,618 long island NY A Ari440 master
Ari440 master A Joined: Oct 2004 Posts: 5,618 long island NY	its a 4.30 stroker crank and 6.8 long 2.20 /9.90 pin rods from OHIO CRANKS bougth a milidon stroker wingage tray but didnt fit the oil pan I used the stock milidon wingage tray but modified it to work , hammered it out in the middle and cut open the slots in it its close like you would use a windge scrapper 1.39 9.85 - 137 mph

Re: Milodon 30931 Oil Pan [Re: Ari440] #471920 09/18/09 06:34 PM 09/18/09 06:34 PM
Joined: Feb 2007 Posts: 6,295 U.S. M moparniac OP master
moparniac OP master M Joined: Feb 2007 Posts: 6,295 U.S.	Quote: its a 4.30 stroker crank and 6.8 long 2.20 /9.90 pin rods from OHIO CRANKS bougth a milidon stroker wingage tray but didnt fit the oil pan The milodon windage tray didnt fit the milodon pan? didnt it set flush on the pan or what....... thx Mopar Performance

Re: Milodon 30931 Oil Pan [Re: moparniac] #471921 09/18/09 07:15 PM 09/18/09 07:15 PM
Joined: May 2009 Posts: 834 Missouri G galen super stock
galen super stock G Joined: May 2009 Posts: 834 Missouri	I used the 30931 with 4.150 stroke and the 32005 windage tray and it cleared fine. Used stock dipstick in block. All I had to do was grind out the hole in the windage tray a little for dipstick clearance.

Re: Milodon 30931 Oil Pan [Re: galen] #471922 09/18/09 07:32 PM 09/18/09 07:32 PM
Joined: Feb 2007 Posts: 6,295 U.S. M moparniac OP master
moparniac OP master M Joined: Feb 2007 Posts: 6,295 U.S.	Quote: I used the 30931 with 4.150 stroke and the 32005 windage tray and it cleared fine. Used stock dipstick in block. All I had to do was grind out the hole in the windage tray a little for dipstick clearance. Awesome.... I run a 4.150 stroke and have the 32005 tray. here is a article I just found http://www.carcraft.com/techarticles/ccrp_0709_440_mopar/dyno_testing.html Parts listed were the 32005 windage tray and the 30931 pan.... Last edited by WeDgiE; 09/18/09 07:33 PM. Mopar Performance

Re: Milodon 30931 Oil Pan [Re: moparniac] #471923 09/18/09 09:22 PM 09/18/09 09:22 PM
Joined: Oct 2004 Posts: 5,618 long island NY A Ari440 master
Ari440 master A Joined: Oct 2004 Posts: 5,618 long island NY	Quote: Quote: its a 4.30 stroker crank and 6.8 long 2.20 /9.90 pin rods from OHIO CRANKS bougth a milidon stroker wingage tray but didnt fit the oil pan The milodon windage tray didnt fit the milodon pan? didnt it set flush on the pan or what....... thx it was the stroker tray that didnt fit 1.39 9.85 - 137 mph

Re: Milodon 30931 Oil Pan [Re: Ari440] #471924 09/18/09 10:28 PM 09/18/09 10:28 PM
Joined: Jun 2008 Posts: 565 IA L landon1 mopar
landon1 mopar L Joined: Jun 2008 Posts: 565 IA	the milodon windage tray didn't fit my stock stroke 440 - rods were scraping the tray - dunno if they thought i was going to run double gaskets between motor and tray or what...waste of $50 '71 Satellite Sebring 440

Re: Milodon 30931 Oil Pan [Re: landon1] #471925 09/19/09 11:10 AM 09/19/09 11:10 AM
Joined: Jan 2003 Posts: 75,043 U.S.S.A. JohnRR I Win
JohnRR I Win Joined: Jan 2003 Posts: 75,043 U.S.S.A.	I fitted the standard milodon tray to my 3.9 stroke/BBC pin size low deck stroker, cleared the rods and crank fine and it fit in a stock 402 pan , I just had to add holes for the rear main cap studs , which I didn't need to do because I had to shorten them so the pan would fit

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1