Milodon 30931 Oil Pan

Posted By: moparniac

Milodon 30931 Oil Pan - 09/18/09 09:05 PM

Do any of you guys runs this pan on a BB Stroker A Body car..... says is good for only 3.750 stroke.... says no dipstick provision either

what about a windage tray also.... thx

http://www.summitracing.com/parts/MIL-30931/?image=large

Posted By: Ari440

Re: Milodon 30931 Oil Pan - 09/18/09 09:58 PM

Posted By: Ari440

Re: Milodon 30931 Oil Pan - 09/18/09 09:59 PM

Posted By: moparniac

Re: Milodon 30931 Oil Pan - 09/18/09 10:05 PM

ARI dont you have a stroker motor? directions say maximum stroke of 3.750 ? also do you run a windage tray? thx

Posted By: Ari440

Re: Milodon 30931 Oil Pan - 09/18/09 10:17 PM

its a 4.30 stroker crank and 6.8 long 2.20 /9.90 pin rods from OHIO CRANKS

bougth a milidon stroker wingage tray but didnt fit the oil pan

I used the stock milidon wingage tray but modified it to work , hammered it out in the middle and cut open the slots in it

its close like you would use a windge scrapper

Posted By: moparniac

Re: Milodon 30931 Oil Pan - 09/18/09 10:34 PM

Quote:

its a 4.30 stroker crank and 6.8 long 2.20 /9.90 pin rods from OHIO CRANKS

bougth a milidon stroker wingage tray but didnt fit the oil pan

The milodon windage tray didnt fit the milodon pan? didnt it set flush on the pan or what....... thx

Posted By: galen

Re: Milodon 30931 Oil Pan - 09/18/09 11:15 PM

I used the 30931 with 4.150 stroke and the 32005 windage tray and it cleared fine. Used stock dipstick in block. All I had to do was grind out the hole in the windage tray a little for dipstick clearance.

Posted By: moparniac

Re: Milodon 30931 Oil Pan - 09/18/09 11:32 PM

Quote:

I used the 30931 with 4.150 stroke and the 32005 windage tray and it cleared fine. Used stock dipstick in block. All I had to do was grind out the hole in the windage tray a little for dipstick clearance.

Awesome.... I run a 4.150 stroke and have the 32005 tray. here is a article I just found

http://www.carcraft.com/techarticles/ccrp_0709_440_mopar/dyno_testing.html

Parts listed were the 32005 windage tray and the 30931 pan....

Posted By: Ari440

Re: Milodon 30931 Oil Pan - 09/19/09 01:22 AM

Quote:

Quote:

its a 4.30 stroker crank and 6.8 long 2.20 /9.90 pin rods from OHIO CRANKS

bougth a milidon stroker wingage tray but didnt fit the oil pan

The milodon windage tray didnt fit the milodon pan? didnt it set flush on the pan or what....... thx

it was the stroker tray that didnt fit

Posted By: landon1

Re: Milodon 30931 Oil Pan - 09/19/09 02:28 AM

the milodon windage tray didn't fit my stock stroke 440 - rods were scraping the tray - dunno if they thought i was going to run double gaskets between motor and tray or what...waste of $50

Posted By: JohnRR

Re: Milodon 30931 Oil Pan - 09/19/09 03:10 PM

I fitted the standard milodon tray to my 3.9 stroke/BBC pin size low deck stroker, cleared the rods and crank fine and it fit in a stock 402 pan , I just had to add holes for the rear main cap studs , which I didn't need to do because I had to shorten them so the pan would fit