|
It won't start. My turn!
#358326
06/26/09 08:48 AM
06/26/09 08:48 AM
|
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
70Cuda383
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
Hmm...just my luck! I wire in a kill switch, and now it won't start! The only thing I changed in the engine compartment is that the alternator charge wire no longer goes to the power box but now goes straight to the battery
It has gas, electric pump is running fine, accelerator pumps squirt fuel like normal, I have 11.9 volts at the coil and the orange box...did my coil or orange box freakishly go out the first time I tried to start it after rewiring the battery to have a kill switch?
Engine cranks like normal
Without a helper to turn the key while I check for spark, how can I test the coil or box? I left the key in the on position and unplugged the distributor to jump the wires thinking it would trigger the box to fire the coil, and had the main wire from coil to distributor unplugged and close to a ground to see if it would spark and there was nothing.
I noticed that my coil negative terminal was also reading 11.9 volts...that can't be right, can it?
With the key off, the coil had zero resistance accross it, so that's ok, right?
Where so I go from here?
Vehicle is a 98 Dakota with a carb'd big block, orange box ignition, and an mad blaster coil, no ballast resistor. It's got 3 years and 3500 miles with this set-up and worked fine 4 days ago, I know the orange boxes are known to go out on this set-up, did mine decide to go out right when I changed the main battery run to include a kill switch?
**Photobucket sucks**
|
|
|
Re: It won't start. My turn!
[Re: 70Cuda383]
#358327
06/26/09 09:04 AM
06/26/09 09:04 AM
|
Joined: Nov 2003
Posts: 36,040
Lincoln Nebraska
RapidRobert
Circle Track
|
Circle Track
Joined: Nov 2003
Posts: 36,040
Lincoln Nebraska
|
You might start by unhooking all the wire(s) from the coil neg primary terminal & w key on jump this coil terminal to ground,tap tap tap & see if the coil wire held 1/4" from ground sparks. Check that the coil positive pri terminal and the "point" of the ECU plug in connector get fire when the key is turned to "start". You can unhook the brown solenoid wire at the starter relay to keep the starter from cranking until you get this solved
live every 24 hour block of time like it's your last day on earth
|
|
|
Re: It won't start. My turn!
[Re: RapidRobert]
#358328
06/26/09 05:16 PM
06/26/09 05:16 PM
|
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
70Cuda383
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
ok I tried that and the only sparks I got was from the coil negative terminal, nothing from the main lead to the distributor...bad coil?
**Photobucket sucks**
|
|
|
Re: It won't start. My turn!
[Re: 70Cuda383]
#358329
06/26/09 06:18 PM
06/26/09 06:18 PM
|
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
70Cuda383
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
I'm going to have to wait for assistance to check if they have power in "start" position, with the spring loaded key, I can't put it in start and then walk around to check the coil/ignition box.
**Photobucket sucks**
|
|
|
Re: It won't start. My turn!
[Re: 70Cuda383]
#358330
06/26/09 06:27 PM
06/26/09 06:27 PM
|
Joined: Sep 2005
Posts: 5,117
Haslett, MI
7DRRunner
master
|
master
Joined: Sep 2005
Posts: 5,117
Haslett, MI
|
checking mine for a bad coil now, interested to hear responses 
"Good luck on your project."
1970 Road Runner
"Accellertii Incredibus"
|
|
|
Re: It won't start. My turn!
[Re: 70Cuda383]
#358334
06/26/09 08:09 PM
06/26/09 08:09 PM
|
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
70Cuda383
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
I'm at work right now, and haven't had a chance to do much else....
regardless of if the coil and box get power in "start" vs "run" they are definitly getting power in "run" and since I'm not using a ballast, I see no reason why they wouldn't get power in "start" as well.
However...in "run" when I grounded out the coil negative terminal, shouldn't the coil have sparked out the main wire? It wasn't I was getting sparks from my jumper wire, but nothing out of the coil...
**Photobucket sucks**
|
|
|
Re: It won't start. My turn!
[Re: 70Cuda383]
#358335
06/26/09 08:19 PM
06/26/09 08:19 PM
|
Joined: Aug 2003
Posts: 8,716
Baltimore/Denver
64Post
master
|
master
Joined: Aug 2003
Posts: 8,716
Baltimore/Denver
|
Quote:
I'm at work right now, and haven't had a chance to do much else....
regardless of if the coil and box get power in "start" vs "run" they are definitly getting power in "run" and since I'm not using a ballast, I see no reason why they wouldn't get power in "start" as well.
However...in "run" when I grounded out the coil negative terminal, shouldn't the coil have sparked out the main wire? It wasn't I was getting sparks from my jumper wire, but nothing out of the coil...
You had to jinx me... now my junk won't start.  
|
|
|
Re: It won't start. My turn!
[Re: 64Post]
#358336
06/26/09 08:25 PM
06/26/09 08:25 PM
|
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
70Cuda383
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
Quote:
Quote:
I'm at work right now, and haven't had a chance to do much else....
regardless of if the coil and box get power in "start" vs "run" they are definitly getting power in "run" and since I'm not using a ballast, I see no reason why they wouldn't get power in "start" as well.
However...in "run" when I grounded out the coil negative terminal, shouldn't the coil have sparked out the main wire? It wasn't I was getting sparks from my jumper wire, but nothing out of the coil...
You had to jinx me... now my junk won't start.
sorry about that!
I really want to replace the coil...I don't know why. but I also can't afford to swap parts if it's not the coil!
Its just REALLY weird how this happened at the same time that I re-wired the trunk mounted battery and the alternator to put in a master kill switch.
of course, the coil is right next to the alternator, and I might have knocked it working on a stuck bolt...which is why I'm suspect of the coil.
**Photobucket sucks**
|
|
|
Re: It won't start. My turn!
[Re: aarcuda]
#358341
06/26/09 08:39 PM
06/26/09 08:39 PM
|
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
70Cuda383
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
ok. instead of tapping the ground then, I'll hold it grounded, and lift to see if it fires the coil then.
if it's supposed to be grounded EXCEPT when the coil fires...then why did my negative terminal have voltage on it? if it's grounded, shouldn't it read zero volts, and then read volts when the ground is removed, and thus firing the coil?
**Photobucket sucks**
|
|
|
Re: It won't start. My turn!
[Re: aarcuda]
#358343
06/26/09 08:45 PM
06/26/09 08:45 PM
|
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
70Cuda383
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
man, I really hope it's not the tach! a coil is much cheaper!
I'll try that in the morning, thanks!
**Photobucket sucks**
|
|
|
Re: It won't start. My turn!
[Re: 70Cuda383]
#358346
06/26/09 09:07 PM
06/26/09 09:07 PM
|
Joined: Mar 2003
Posts: 15,491
the boonies
aarcuda
I Live Here
|
I Live Here
Joined: Mar 2003
Posts: 15,491
the boonies
|
Quote:
Quote:
The coil is a. Coil. Power on pos goes thru coil and show on the neg terminal. That creates a field when neg is grounded. Remove the gnd and field collapses and jumps to secondary out to plugs ( spark)
ok. I always wondered how the volage going in circles around the middle would create a charge...that makes sense though.
so if the coil is grounded, and then the ground is removed, it SHOULD fire, right? and if it doesn't then it's most likely someting broken in the coil?
I'll try that before hooking the ignition box back up to it and cranking away again to see if ti was the tach or not.
yes. but disconnect the tach cause ive seen tachs cause no start conditions before.
since the coil + to coil - is a coil of wire, there should be a resistance between them. you said it shows open (infinity) right? or was it really low like 0? if its open (infinity) then the coil is bad
|
|
|
Re: It won't start. My turn!
[Re: 70Cuda383]
#358350
06/26/09 09:20 PM
06/26/09 09:20 PM
|
Joined: Mar 2003
Posts: 15,491
the boonies
aarcuda
I Live Here
|
I Live Here
Joined: Mar 2003
Posts: 15,491
the boonies
|
Quote:
Quote:
Quote:
Quote:
The coil is a. Coil. Power on pos goes thru coil and show on the neg terminal. That creates a field when neg is grounded. Remove the gnd and field collapses and jumps to secondary out to plugs ( spark)
ok. I always wondered how the volage going in circles around the middle would create a charge...that makes sense though.
so if the coil is grounded, and then the ground is removed, it SHOULD fire, right? and if it doesn't then it's most likely someting broken in the coil?
I'll try that before hooking the ignition box back up to it and cranking away again to see if ti was the tach or not.
yes. but disconnect the tach cause ive seen tachs cause no start conditions before.
since the coil + to coil - is a coil of wire, there should be a resistance between them. you said it shows open (infinity) right? or was it really low like 0? if its open (infinity) then the coil is bad
it's closed, zero resistance. I didn't know if there was supposed tobe a few ohms of resistance or not.
ahhhh, ya, zero sounds wrong. id expect some resistance. to know what the resistance should be, you'll have to go to the msd site and see if they list it. else you could call them on monday or swap in a different coil.
shouldnt you be running a ballast resister with that coil?
|
|
|
Re: It won't start. My turn!
[Re: aarcuda]
#358352
06/26/09 09:43 PM
06/26/09 09:43 PM
|
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
70Cuda383
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
Quote:
yup, a ballast resister is needed. you probably smoked the coil.
http://www.msdpower.com/download/8202.pdf
but you did just install aa master kill switch. how is it wired. the timing seems very suspicious
I don't think so, they even say that their MSD6 or 7 system delivers 12V to the coil, and that a seperate 12V signal is not needed when using and MSD box, and they said it needs a .8ohm resistor if used on a stock POINTS style ignition...mine is a stock ELECTRONIC style ignition...didn't think a resitor was needed, and like I said, 3 years, 3500 miles...
if it did need a resistor, then yea, I guess I cooked it, but kind of funny that it happened just now!
I don't think the kill switch had anything to do with it...just bad timing. I did move the battery all the way to the back, which added about 10 feet to the main positive battery cable by the time I sent it through the switch...but I still had 11.9V at the coil with the key on and not running, I don't THINK my problem is a voltage drop issue...the volt meter in the dash drops to about 9 or 10 volts while cranking the engine...don't know what it dropped to before, never paid attetion, cause it always started!
the other change was to take the main charge from the alternator to the power distribution box on the driver side inner fender (which then sent it back to the battery, and/or powered everything else on the truck) and sent it back to the battery side of the kill switch. nothing else was changed, and it seems to be working just fine, like I said, it cranks at normal speed, shows 11.9V at the coil, ignition box, etc...
**Photobucket sucks**
|
|
|
Re: It won't start. My turn!
[Re: 70Cuda383]
#358354
06/26/09 09:54 PM
06/26/09 09:54 PM
|
Joined: Mar 2003
Posts: 15,491
the boonies
aarcuda
I Live Here
|
I Live Here
Joined: Mar 2003
Posts: 15,491
the boonies
|
Quote:
Quote:
yup, a ballast resister is needed. you probably smoked the coil.
http://www.msdpower.com/download/8202.pdf
but you did just install aa master kill switch. how is it wired. the timing seems very suspicious
I don't think so, they even say that their MSD6 or 7 system delivers 12V to the coil, and that a seperate 12V signal is not needed when using and MSD box, and they said it needs a .8ohm resistor if used on a stock POINTS style ignition...mine is a stock ELECTRONIC style ignition...didn't think a resitor was needed, and like I said, 3 years, 3500 miles...
if it did need a resistor, then yea, I guess I cooked it, but kind of funny that it happened just now!
I don't think the kill switch had anything to do with it...just bad timing. I did move the battery all the way to the back, which added about 10 feet to the main positive battery cable by the time I sent it through the switch...but I still had 11.9V at the coil with the key on and not running, I don't THINK my problem is a voltage drop issue...the volt meter in the dash drops to about 9 or 10 volts while cranking the engine...don't know what it dropped to before, never paid attetion, cause it always started!
the other change was to take the main charge from the alternator to the power distribution box on the driver side inner fender (which then sent it back to the battery, and/or powered everything else on the truck) and sent it back to the battery side of the kill switch. nothing else was changed, and it seems to be working just fine, like I said, it cranks at normal speed, shows 11.9V at the coil, ignition box, etc...
if the MSD is a capacitive discharge system (which I think it is), the coil gets fired BY THE BOX. both the + and - coil powers comes from the box and not from the ignition feed +12 v) and thats why a ballast resister isnt needed.
But when you use a stock box, the stock (or orange box) only sends the groun d signal to the coil so you need (i believe) a ballast resistor whe nusing the orange box or points
|
|
|
Re: It won't start. My turn!
[Re: aarcuda]
#358355
06/26/09 09:55 PM
06/26/09 09:55 PM
|
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
70Cuda383
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
Yea I saw that. I'll have to see if Ican duplicate the .440 ohms, or if it truely is zero. zero would indicate an internal short in my opinion. I might have had the sensitivity set too high on the voltmeter when it registered a zero.
**Photobucket sucks**
|
|
|
Re: It won't start. My turn!
[Re: 70Cuda383]
#358356
06/26/09 10:05 PM
06/26/09 10:05 PM
|
Joined: Mar 2003
Posts: 15,491
the boonies
aarcuda
I Live Here
|
I Live Here
Joined: Mar 2003
Posts: 15,491
the boonies
|
Quote:
Yea I saw that. I'll have to see if Ican duplicate the .440 ohms, or if it truely is zero. zero would indicate an internal short in my opinion. I might have had the sensitivity set too high on the voltmeter when it registered a zero.
too high a setting would show 0. but after further checking, the MDS 6 and 7 are CD ignitions. thats why they dont need a ballast. im pretty sure you need ballast resistor with the orange box (look at figure 2 in the instructions- it says so)
|
|
|
Re: It won't start. My turn!
[Re: aarcuda]
#358357
06/26/09 10:11 PM
06/26/09 10:11 PM
|
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
70Cuda383
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
all the more reason to finally get off my butt, solder the red and blue wires back together on the used MSD6AL I bought, and get it onto the truck.
...but, I think I'll fix this problem first, before I throw a questionable, used ignition box on there too!
**Photobucket sucks**
|
|
|
Re: It won't start. My turn!
[Re: 70Cuda383]
#358358
06/27/09 01:19 AM
06/27/09 01:19 AM
|
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
70Cuda383
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
when set to the most sensitive setting, my volt meter reads .5 all by itself. Hmm...must be cheap wires or poor calibration
Accross the coil it read 1ohm, minus the .5 of the meter itself, it's coil resistance at .5 I'll say that's in spec with .44!
When I grounded the coil with the key on, and then "broke ground" I did get a very faint spark out of the coil...but it wasn't as big as the spark I got from the ground wire as I removed it from the ground
I'll try starting it tomorrow (when it's not 1am and ok to make noise again!) with the tach unhooked to see if the tach was the problem or not
**Photobucket sucks**
|
|
|
Re: It won't start. My turn!
[Re: 1_WILD_RT]
#358360
06/27/09 12:41 PM
06/27/09 12:41 PM
|
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
70Cuda383
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
Quote:
Where the coil for the Cuda?? FWIW I haven't seen a report on the test light results...
I tore the cuda apart 4 years ago, and have since moved 2 and a half times...it's in a box somewhere. My garage is a pile of boxes, car parts, garage equipment and the cuda...by the end of this summer, I should have my 30x40 shop built, and I can finally spread that stuff out and unpack it!
Both the coil and orange box have power in "run" and in "start". I thought maybe I had a bad ground since the battery is now 6 feet further from the engine, and the ground cable is in a new spot, do I used a jumper to ground the box straight to the neg battery post, still no start. Resistance accross the coil is .5 ohms, but shows an open from the positive terminal to the coil wire..,Is this normal? Or should it be .5 like the terminals?
After seeing how weak the spark was last night by grounding the coil and making it fire, I think it's a weak coil...finally burnt out from not running a ballast maybe? Just freak timing!
I think I'm ready to replace it and see what happens, unless I can check something else? (I guess I could get a helping hand and have someone crank the engine while checking the coil spark that way yet too)
**Photobucket sucks**
|
|
|
Re: It won't start. My turn!
[Re: 1_WILD_RT]
#358362
06/27/09 06:09 PM
06/27/09 06:09 PM
|
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
70Cuda383
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
test light results! no dice.  wired up the test light to the coil positive, and the coil negative, with the key on, it should light up, right? it doesn't it doesn't flash while cranking either. tach wire is pulled way out of the way too, so no interferance from that. I DID have the orange box from the cuda, it was still on the firewall...but hasn't run in 4 years. same results. no light. so...2 bad boxes? bad ground to box? I thought I tested that too, by putting a jumper from the case of the box straight to the negative battery terminal, I attached it at the screw that holds it to the inner fender, which touches bare unpainted metal on the box, and I attached it to the blue annodized thing on the front, and it wouldn't start when I tried that. with a helper (the wife reluctantly gave me about 45 seconds of her time  ), I had it all hooked up and pulled a plug, had her crank, and no sparks. oh yea...I succumbed...brand new coil while she was doing this
**Photobucket sucks**
|
|
|
Re: It won't start. My turn!
[Re: 1_WILD_RT]
#358365
06/27/09 06:45 PM
06/27/09 06:45 PM
|
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
70Cuda383
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
Quote:
Test light, ground the clamp, hook the probe up to coil negative post...Leave the coil hooked up.. Wish I was closer..
ok...but the test light was the last thing I tried.
I was so sure it was the coil, so that was what I did first.
that didn't work, so I had my wife crank with a spark plug pulled, looking for spark. it's either so weak it can't be seen, or not there.
changed the orange box, with the old one from the cuda that worked when I pulled it apart 4 years ago, and still no spark at the spark plug. and I had a jumper from the strap of the plug straight to the battery to ensure good ground there as well...
I'll give the light a shot, but...at this point, I don't know what could be the problem.
the gap at reluctor? ...the magnet and star wheel inside the distributor...is very tight, I didn't measure it but it looks like it's less than the thickness of a sheet of notebook paper.
I don't get it!
if I get a few minutes after dinner, I'll re-try the test light with the coil hooked up properly.
**Photobucket sucks**
|
|
|
Re: It won't start. My turn!
[Re: aarcuda]
#358368
06/27/09 07:07 PM
06/27/09 07:07 PM
|
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
70Cuda383
OP
Too Many Posts
|
OP
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
I'm laughing right now. problem found, problem fixed, engine started, and my new kill switch works like it should and shuts down everything. the problem was the coil negative wire to the orange box...was brittle and broke...but the heat shrink tubing was holding the connector onto the end of the wire...I found this as I was doing the test light the RIGHT way...light didn't flash at all...steady on. I went to pull the plug on the box to swap the box to the other one, as now I don't know which one is which...and I slipped, and tugged on the wire enough to pull it out of the heat shrink...I thought "hmm...I bet that's been my problem the whole time. grabbed another connector, stripped the end of the wire, crimped it on, tossed it on the coil, and the darn thing fired right up! I guess I'll test the other orange box so I know if it's still good or not, then put the oil coil on to see if it is still good...as it probably is, and take the new coild back...that's $42 the wife will be happy I didn't spend! I guess next time, I know to ohm out the wires too, not just the components!   Thanks for the help guys...guess I didn't need it!
**Photobucket sucks**
|
|
|
|
|
