Big Block Water Pump With Water Pump Housing. Used, $100 + Shipping. Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Note: Came off a 1970 383 motor

Holley 4749 Carburetor Factory 383-440. Used, $125 + Shipping. Payment via US Postal Money Order. Shipping: US Address Only!
Call Steve 810-629-1097
Note: Came off a 70 383 Challenger

Factory Valve Cover Breather. Used, $15 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Valve Cover Oil Fill Caps. Used, $10 Each + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!

1. Not sure!
2. 73-74 model (came of my 73 Cuda)
3. Mopar Preformance Chrome New!
Call Steve 810-629-1097
Note: Pick the one you want by photo 1-3

73-74 Electric Choke #3656730 All Models, Used, $30 + Shipping. Payment via US Postal Money Order. Shipping: US Address Only!
Call Steve 810-629-1097

Fram CA160 Air Filter. New, $5 + Shipping. Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Note: Used On Any 2bl Motor, See Photo 2 For Application!

63-76 Temperature Sending Switch #2426458 Used $7.50 + Shipping
62-80 Oil Pressure Sending Unit For Models With Warning Light. Used, $7.50 + Shipping.
Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Factory Carburetor 3.5 in" Stud With Wing Nut. Used, $10 + Shipping. Payment via US Postal Money Order. Shipping: US Address Only!
Call Steve 810-629-1097

Water Pump To Fan Spacer 1.25 in' Thick. Used $15 + Shipping. Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Gates Single Belts.New, $10 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!

1.Gates Belt 7470
2. Gates Belt 7490
3. Gates Belt 7580

Call Steve 810-629-1097
Note: Pick the one you want by photo 1-3

Gates / Mopar Duel Alternator / Fan Belts.New, Price Below + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!

1.Gates Duel Belt #7541 $20
2. Mopar Duel Belt #4106241 $25

Call Steve 810-629-1097
Note: Pick the one you want by photo 1-2

1969 440 HP block WS23L9G175918 or WS27L9G175918

You can see it is missing the body character in the stamping.
If you have one of those cars I could trade you parts if you wanted to reunite car and block.

Been in dry storage for many years. .030 and has 1 sleeve. $500 obo for block, caps, crank. Plus shipping if that is something you'd be interested in. Available in 52205 or 60188.

More photos available

For Sale, 1968 D model year 440 HP block, main caps and steel crank. Block is standard bore but has corrosion in 3 cylinders that should clean up under .060.
Casting date is 9/20/67
$600 obo

Can deliver to mopar shows in Stillwater MN, Carlisle or the nats with pre payment.

Located in menomonie, wi

Thanks

I have two sets and 4 spare BBM used main cap sets for the 2.75" crank journal. See pictures below.

$50 a set or $80 for the whole lot shipped in the lower 48 states. I will ship elsewhere for the added shipping cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

The 505ci that I’m selling is a pretty extensive build that produces a peak horsepower of 631@ 5,500rpm and 659lbs. ft. of torque at 4,500rpm all on 93 octane gas pumped from a Shell gas station down the street.

You’ll receive the full dyno report if you purchase it.

The parts list is as follows:

Chrysler RB440 engine block (7/8/1977) bored 0.030” over
K1 Technologies 4.25” stroke crank, 8-bolt Hemi flange
K1 Technologies 7.100” H-beam connecting rods
MAHLE Power Pak flat top pistons (11.7:1 compression, 0.025” in the hole)
MAHLE rings
Clevite bearings
SB Concepts billet main caps
SB Concepts billet steel girdle
ARP main studs
ARP cylinder head bolts
ARP intake manifold bolts
Mancini billet aluminum rear main seal
Milodon High Pressure Oil Pump
Milodon 3/8” pick up tube
Milodon 7qt. low profile pan

Trick Flow PowerPort Top End Engine Kit:
• Trick Flow PowerPort 240 aluminum cylinder heads (78cc chambers)
• Trick Flow Track Heat square bore 4150 single plane intake manifold
• Trick Flow dual valve springs
• Harland Sharpe roller rockers & shafts
• Howard Cams hydraulic roller lifters
• COMP Cams push rods
• Trick Flow hydraulic roller camshaft (243 int./247 exh. @ .050” lift, 0.640 int./0.640 exh.)

COMP Cams bronze gear oil pump driveshaft
COMP Cams double roller timing chain
Milodon bronze gear intermediate shaft
PRW baffled, aluminum valve covers
440 Source hydraulic damper
440 Source crank & water pump pulley
Mancini aluminum water pump & housing
Mancini stamped valley pan
440 Source valley pan retainers & hardware

*This does not include carburetor, ignition (distributor, plugs or wires), or exhaust. Long block only.

Just by the parts list and machine work is a $16,800 engine, but I’m asking $14,500 or best offer.

email me directly at charged1969@hotmail.com

Brand New in the box Big Block Chrysler/Mopar Pro-Flo XT EFI Part # 7144 Manifold

Designed for 413-440 Chrysler motors, the Pro-Flo XT Chrysler 440 EFI intake manifold is engineered with a large plenum and long tapered runners to deliver maximum horsepower. This manifold delivers a broad torque band throughout the rpm range of 1500-7000 rpm. $450 + shipping PM here or Phone (716) 655-0625 this is a land line. Ask for Gary This manifold sell for $668 at Jegs and Summit

SMR transmissions B/RB to small block transmission adapter kit. Part number SM 99-100P for a 6 bolt crank. New in box, the box has been opened but only for inspection, never installed the kit. for info: https://smrtrans.tripod.com/smrtransmissionsintro/id9.html $400 + shipping. PM here or phone (716) 655-0625 ask for Gary or leave a message ( this is a land line)

For sale - 516 heads that have been in my basement work room for a 5+ years - they came (just as you see in the pics) along with an engine block I purchased that I needed for a resto. - looks like a rebuild/refresh was done.

Rather not ship - I'm in MD - happy to travel a few hours to meet.

$200 - shoot me a PM

Just re - joined Moparts - Hi All..

For sale - 70's 440 cast crank - stored in same basement as the heads I posted - some rust but maybe savable - quick measurement on journals - all 2.375
Rather not ship - I'm in MD - happy to travel a few hours to meet.

$100 - PM if interested

1967 Carter 383 Carburetor 4298S

Used, Original 1967 Carter 4298S (A7 = Jan. 1967) Carb, for 383 engine with manual transmission.
Needs to be restored. Missing a few bolts & secondary throttle shaft/plate assembly.
Asking $95 shipped in US.
If interested or need more pictures, send email: chargercrazed@usa.com