|
Re: 6 point roll bar cost
[Re: justinp61]
#2984054
11/11/21 10:07 AM
11/11/21 10:07 AM
|
Joined: Jan 2003
Posts: 1,610 westerly, ri. usa
440lebaron
top fuel
|
top fuel
Joined: Jan 2003
Posts: 1,610
westerly, ri. usa
|
DOING side bars and bars from cross bar to floor next week end, M/S tig S&W kit fit perfect
gary yes its a cordoba
Last edited by 440lebaron; 11/11/21 10:15 AM.
all parts are sold as is, all parts are considered used no warranties or returns paypal/check/money order, shipping is from zip 02891, buyer pays paypal fees 24% IRS 1099A plus 3% of part price, check/money order preferred site is not monitored 24/7 there might be a delay in response
|
|
|
Re: 6 point roll bar cost
[Re: DrCharles]
#2984168
11/11/21 03:53 PM
11/11/21 03:53 PM
|
Joined: Oct 2006
Posts: 246 Cranberry Twp PA (North of Pit...
rumblefish72
enthusiast
|
enthusiast
Joined: Oct 2006
Posts: 246
Cranberry Twp PA (North of Pit...
|
Pictures of my roll bars ... yes, needs a repainting. Also included two pictures of through-the-floor the subframe connectors. The unibody was very flexible before installation. It's very rigid now.
1972 Pro-Street 'Cuda, 500" Eagle stoker B Block, Eddy RPM heads, Victor Manifold, 850 Mighty Demon, Hemi 4 Speed, Dana 60 w/4.88 gears - Built by Hansen Racing Middlesex - NJ
|
|
|
Re: 6 point roll bar cost
[Re: rumblefish72]
#2984279
11/11/21 09:12 PM
11/11/21 09:12 PM
|
Joined: Jul 2018
Posts: 172 Sticky South
Rodenteliminator
member
|
member
Joined: Jul 2018
Posts: 172
Sticky South
|
I bought my 12 point thru Applied Racing Technology in Clearwater Fl. a couple of years back and it fit very well up and tight (67 BBody) with plenty of extra pipe, good guys to work with and they have a good bunch of programs for about any vehicle.
Sorry honey I spent the rent
|
|
|
Re: 6 point roll bar cost
[Re: TruPerformance]
#2985003
11/14/21 12:54 AM
11/14/21 12:54 AM
|
Joined: May 2008
Posts: 984 San Diego CA
65 Hemi
super stock
|
super stock
Joined: May 2008
Posts: 984
San Diego CA
|
Aluminum foil is your friend when painting a cage. Much better than masking paper and tape
Doug
MOPAR or NO CAR!!! 1965 Dodge Coronet soon a 6.1 Hemi with a Magnson blower 810 hp on pump gas 1964 Dodge Polara 582" Indy alum Block 426-1RA heads, 1933 Plymouth PE all Steel, LT1 4L60E 1959 Plymouth Savoy 33,000 mile survivor Old cars are never done. They are ongoing projects!
|
|
|
Re: 6 point roll bar cost
[Re: JERICOGTX]
#2985278
11/14/21 10:26 PM
11/14/21 10:26 PM
|
Joined: Nov 2009
Posts: 3,082 St. Paul , Mn.
tubtar
master
|
master
Joined: Nov 2009
Posts: 3,082
St. Paul , Mn.
|
[/quote] I'm sure I'll piss some people off, but "kits" fit like garbage. There is a big difference between a custom bent cage for YOUR car, vs. a kit that anyone can install. [/quote] I have had occasions in life where the truth pissed me off. This isn't one of them. I have installed S&W , Art Morrison and Alston kits in cars................the fit was what I made it , and trying to put one of them in " as is " just ain't happening.
|
|
|
Re: 6 point roll bar cost
[Re: justinp61]
#2985291
11/14/21 10:41 PM
11/14/21 10:41 PM
|
Joined: Jun 2014
Posts: 3,237 Md.
carnut68
master
|
master
Joined: Jun 2014
Posts: 3,237
Md.
|
The bar in my Dart came from S&W, everything was long so it could be fit up nice and tight. The main hoop is within 1/2" of the inner panel on each side. It's better than I expected and wouldn't hesitate to use them again. The painting is a pain but I brushed o a hammered finish paint and it came out well. Same here. I measured made sure car was level then cut and tacked it together and a friend who could weld finished it up. The car really stiffened up after adding the frame connectors and bar.
America First!
|
|
|
|
|
|