1 78" headers avail for 64 Belvedere with 383? - Moparts Forums

Register Log In Moparts Forums Moparts Question and Answer 1 78" headers avail for 64 Belvedere with 383?

Print Thread

1 78" headers avail for 64 Belvedere with 383? #2521943 07/14/18 09:14 PM 07/14/18 09:14 PM
Joined: Jul 2005 Posts: 1,954 Blairsden, CA T Triggerfish OP top fuel
Triggerfish OP top fuel T Joined: Jul 2005 Posts: 1,954 Blairsden, CA	Has anyone installed 1 78" headers in a 64 B body with low deck motor? If so, any fittment problems or mods needed?

Re: 1 78" headers avail for 64 Belvedere with 383? [Re: Triggerfish] #2522080 07/15/18 11:47 AM 07/15/18 11:47 AM
Joined: Jun 2008 Posts: 3,916 usa L lewtot184 master
lewtot184 master L Joined: Jun 2008 Posts: 3,916 usa	to my knowledge nobody makes a 1 7/8" header for an early b-body. I think you can use a tti 1 7/8" if you use the later k-member the sets the engine back.

Re: 1 78" headers avail for 64 Belvedere with 383? [Re: Triggerfish] #2522116 07/15/18 01:27 PM 07/15/18 01:27 PM
Joined: Jan 2003 Posts: 21,074 Niles , Ohio T therocks oh wait.but hey.lets see.oh yeah.
therocks oh wait.but hey.lets see.oh yeah. T Joined: Jan 2003 Posts: 21,074 Niles , Ohio	I ran a set inm my 65 the same body/I ran a 440 though.Still have them hanging in the other garage as I run 2 inch TTIs.If TTi makes a set for 65 they should fit 64.Oh there are no B bodys in 64.All Plymouhs wre the same body just different trim same with dodge except for such as dart valiant etc.Rocky Chrysler Firepower

Re: 1 78" headers avail for 64 Belvedere with 383? [Re: therocks] #2522131 07/15/18 02:03 PM 07/15/18 02:03 PM
Joined: Jul 2005 Posts: 1,954 Blairsden, CA T Triggerfish OP top fuel
Triggerfish OP top fuel T Joined: Jul 2005 Posts: 1,954 Blairsden, CA	Thanks for the info & I guess I'll call Dougs & TTI tomorrow to see what they've got.

Re: 1 78" headers avail for 64 Belvedere with 383? [Re: Triggerfish] #2522149 07/15/18 02:59 PM 07/15/18 02:59 PM
Joined: Sep 2003 Posts: 1,935 Grove, OK hosehead top fuel
hosehead top fuel Joined: Sep 2003 Posts: 1,935 Grove, OK	I was in the same situation when I built my street strip motor. Went from the 1-3/4" tti to the 2" as they don't offer 1-7/8". 2" headers still fit great on ,y 65 belvedere. Tti is a great product. 63 Plymouth savoy 65 d100 66 dart race project 58 plymouth suburban

Re: 1 78" headers avail for 64 Belvedere with 383? [Re: Triggerfish] #2522169 07/15/18 03:34 PM 07/15/18 03:34 PM
Joined: Jun 2008 Posts: 3,916 usa L lewtot184 master
lewtot184 master L Joined: Jun 2008 Posts: 3,916 usa	the 1 7/8" tti's are made for the '66 and up chassis.

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1