Finally Dynoed my new bullet today
#250160
03/10/09 10:09 PM
03/10/09 10:09 PM
|
Joined: Aug 2003
Posts: 1,123 Seaford Delaware
JSR1485
OP
super stock
|
OP
super stock
Joined: Aug 2003
Posts: 1,123
Seaford Delaware
|
After a long wait and some problems dynoed my new 367ci small block today I was impressed you think it will put me in the 10's 575 hp @ 6800 rpm 490ft torque @ 5300 rpm's Darn Cometic gaskets keep leaking around the head studs Car weights 3125 8" 5500 stall converter 4.56 gears 30 " tall slick Cal racs and Mono leafs
Switched to the dark side...
|
|
|
Re: Finally Dynoed my new bullet today
[Re: JSR1485]
#250164
03/10/09 11:27 PM
03/10/09 11:27 PM
|
Joined: Jan 2003
Posts: 14,513 So. Burlington, Vt.
fast68plymouth
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 14,513
So. Burlington, Vt.
|
weedlayers 419 made like 580hp. runs 10.40's-50's in a 3400lb Challenger.
68 Satellite, 383 with stock 906’s, 3550lbs, 11.18@123 Dealer for Comp Cams/Indy Heads
|
|
|
Re: Finally Dynoed my new bullet today
[Re: JSR1485]
#250165
03/11/09 09:50 AM
03/11/09 09:50 AM
|
Joined: Aug 2008
Posts: 189 long island new york
kingdust
member
|
member
Joined: Aug 2008
Posts: 189
long island new york
|
I had a .040 340 with w2 econos made 540 at the flywheel, with a 4spd and 489 gears in a 3000lb duster,I went a best of 10.70 at 125 at atco! I launched at 6000,anything below that and the car would bog off the line because it didn't make a lot of torque. You'll definately be in mid 10s. Good luck.
LIFE IS A LESSON,YOU LEARN IT WHEN YOUR THROUGH!
|
|
|
Re: Finally Dynoed my new bullet today
[Re: kingdust]
#250166
03/11/09 10:48 AM
03/11/09 10:48 AM
|
Joined: Jan 2003
Posts: 1,855 Staten Island N.Y.
Dap
top fuel
|
top fuel
Joined: Jan 2003
Posts: 1,855
Staten Island N.Y.
|
Jason I am glad to see you have the new bullet up and running.. Nice numbers by the way.. See ya at the track
PRH446 10.084 @ 135.21 mph N/A through chambered mufflers,3300lbs. Stock stroke wedge
|
|
|
Re: Finally Dynoed my new bullet today
[Re: Dap]
#250168
03/11/09 04:39 PM
03/11/09 04:39 PM
|
Joined: Aug 2003
Posts: 1,123 Seaford Delaware
JSR1485
OP
super stock
|
OP
super stock
Joined: Aug 2003
Posts: 1,123
Seaford Delaware
|
Thanks Rob hope to see you at Etown once again, No sure what the problems was with head gaskets yet. I am waiting to hear back from Dave @ RBRE They Dyno'd it again to and the HP went up to 585HP and the torque went up also. Not bad for a steel headed small block
Switched to the dark side...
|
|
|
Re: Finally Dynoed my new bullet today
[Re: 2QUICK4U]
#250170
03/11/09 04:55 PM
03/11/09 04:55 PM
|
Joined: Aug 2007
Posts: 498 El Dorado Ca
65signet
mopar
|
mopar
Joined: Aug 2007
Posts: 498
El Dorado Ca
|
What do you have into that 367... heads, cam, comp ratio, what size carb, i have a 365 but i am not going to dyno it and was wondering how close my set up is to yours.
thanks
1965 Plymouth Barracuda 273 M/SA 1970 Plymouth Duster 360/904 10.60s with J heads
|
|
|
Re: Finally Dynoed my new bullet today
[Re: 65signet]
#250171
03/11/09 08:20 PM
03/11/09 08:20 PM
|
Joined: Aug 2003
Posts: 1,123 Seaford Delaware
JSR1485
OP
super stock
|
OP
super stock
Joined: Aug 2003
Posts: 1,123
Seaford Delaware
|
I have Scat crank, Scat H beam rods, Diamond special made pistons -12.8 to 1 ,Cam Motion roller cam 690/700 106.5 center 1.7 and 1.6 jessel rockers, Steel heads flowed by Brandywine heads for I.R.O.C flow 297cfm @ 700 lift ,Victor 340 intake 750 holley HP carb redone.
Switched to the dark side...
|
|
|
Re: Finally Dynoed my new bullet today
[Re: JSR1485]
#250172
03/11/09 10:43 PM
03/11/09 10:43 PM
|
Joined: Aug 2007
Posts: 498 El Dorado Ca
65signet
mopar
|
mopar
Joined: Aug 2007
Posts: 498
El Dorado Ca
|
You have alot more compression and cam than i do.. is that just a 360 bored out or a storker
1965 Plymouth Barracuda 273 M/SA 1970 Plymouth Duster 360/904 10.60s with J heads
|
|
|
Re: Finally Dynoed my new bullet today
[Re: JSR1485]
#250174
03/14/09 12:16 AM
03/14/09 12:16 AM
|
Joined: Jan 2003
Posts: 17,918 Akron, Ohio
ProSport
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 17,918
Akron, Ohio
|
Happy b-day! And nice dyno numbers!
1970 Challenger, all aluminum 528 Hemi, HDK suspension, Tremec 5 speed manual
|
|
|
|
|