Page 1 of 2 1 2 >
Topic Options
#2380314 - 10/01/17 09:38 PM DIY/Home Alignment Tools - What do you use?
GoodysGotaCuda Online   penguin-006
5.7L Hemi, 6spd

Registered: 11/23/04
Posts: 24358
Loc: Texas
I am interested in picking up some DIY home wheel alignment tools to setup my car and probably use it on a few other vehicles I have around.

I have seen Longacre and Quick Trick, are there any other common setups out there?

I am thinking of buying a digital caster/camber gauge, some wheel mount, toe plates and likely some turn plates.

My Hotchkis UCAs are too much of a pain to have a shop reasonably align the car. spank
_________________________
1972 Barracuda - 5.7L Hemi, T56 Magnum 6spd - Build page -> https://www.facebook.com/GoodysGotaHemi<-
1976 Dodge Warlock - "Her Truck" - 360/727 2wd
1969 Dodge Dart Custom Sedan - Grandma Edition - 318/904
2016 Subaru WRX - E30 Tune ~320whp

Top
#2380344 - 10/01/17 10:34 PM Re: DIY/Home Alignment Tools - What do you use? [Re: GoodysGotaCuda]
autoxcuda Offline
Too Many Posts

Registered: 01/20/03
Posts: 25946
Loc: So Cal
I went with the longacre because I thought I could used the digital angle finder for other projects.

The rim clamps on the Longacre nor Fastrxx are not extremely robust. I used a bungee around the unit to hold it to the rim. I think the Longacre could be a tad more stable. But that could be my mind playing trick cause it looks a lot sexier.

Two pieces of plywood with a slot would work as good as the Longacre toe plate. Honestly I just hooked the tape to a tread and measured to the same tread-line in the other side.

The two plates are expensive. I used greased sheets. Plates would make the caster angle procedure quicker. It would be more accruate too, but think I/we getting that perfect may not be that necessary.



Attachments
IMG_0272.JPG

IMG_0271.JPG




Edited by autoxcuda (10/01/17 10:59 PM)
_________________________
Fall Fling 23
October 27, 2018
Woodley Park, Van Nuys CA
www.cpwclub.com
300+ show cars, 150+ swap, manf. midways
Malibu Cruise, Cruise-In
Free Spectator Admission!

Top
#2380347 - 10/01/17 10:39 PM Re: DIY/Home Alignment Tools - What do you use? [Re: GoodysGotaCuda]
autoxcuda Offline
Too Many Posts

Registered: 01/20/03
Posts: 25946
Loc: So Cal
I think two greased plates and marking the caster angle like joelson6 did here:

http://board.moparts.org/ubbthreads/ubbt...mendations.html
_________________________
Fall Fling 23
October 27, 2018
Woodley Park, Van Nuys CA
www.cpwclub.com
300+ show cars, 150+ swap, manf. midways
Malibu Cruise, Cruise-In
Free Spectator Admission!

Top
#2380367 - 10/01/17 11:10 PM Re: DIY/Home Alignment Tools - What do you use? [Re: autoxcuda]
RUNCHARGER Offline
I Live Here

Registered: 01/20/03
Posts: 15664
Loc: Chilliwack B.C. Canada
I have a fastrxx and marked up a couple of ceramic floor tiles (I put masking tape on the floor so I know the tiles don't move), they work great. I measure toe in from inside wheel edge to inside wheel edge. I have measured from tire tread but trust the wheel edges more, it can be a hassle if you have headers though.


Edited by RUNCHARGER (10/01/17 11:14 PM)
_________________________
Sheldon

Top
#2380402 - 10/02/17 12:04 AM Re: DIY/Home Alignment Tools - What do you use? [Re: GoodysGotaCuda]
astjp2 Offline
master

Registered: 01/18/11
Posts: 4174
Loc: Utah and Alaska
Do you plan on doing a bump steer check too?
_________________________
1941 Taylorcraft
1968 Charger
1994 Wrangler
1998 Wrangler
2008 Kia Rio
2017 Jetta

I didn't do 4 years and 9 months of Graduate School to be called Mister!

Top
#2380430 - 10/02/17 05:30 AM Re: DIY/Home Alignment Tools - What do you use? [Re: GoodysGotaCuda]
BigBlockMopar Offline
master

Registered: 01/22/03
Posts: 3387
Loc: The Netherlands
iPhone app: iAlign




iPhone app: CamberMeas
With this app you can enter your steeringratio and just turn the wheel left and right a certain amount, the app will calculate the rest.





_________________________
BigBlockMopar.com


Top
#2380527 - 10/02/17 10:37 AM Re: DIY/Home Alignment Tools - What do you use? [Re: autoxcuda]
rustbuckett68 Offline
mopar

Registered: 06/17/06
Posts: 593
Loc: Alberta
Couple of sticks and some tie wire make a thingy to check toe. Wrap the wire around the tire to hold the sticks at about the center of the tire, and measure front and back. They can be adjusted to clear some of the under car stuff. What is the latest secret to posting pictures??

Top
#2380532 - 10/02/17 10:47 AM Re: DIY/Home Alignment Tools - What do you use? [Re: BigBlockMopar]
67R/T4speeder Offline
pro stock

Registered: 02/03/07
Posts: 1520
Loc: Pismo Beach,California
Originally Posted By BigBlockMopar
iPhone app: iAlign




iPhone app: CamberMeas
With this app you can enter your steeringratio and just turn the wheel left and right a certain amount, the app will calculate the rest.









Cannot find this App.
_________________________
Andy








www.troxellsgarage.com

Top
#2380593 - 10/02/17 12:25 PM Re: DIY/Home Alignment Tools - What do you use? [Re: GoodysGotaCuda]
BigBlockMopar Offline
master

Registered: 01/22/03
Posts: 3387
Loc: The Netherlands
_________________________
BigBlockMopar.com


Top
#2380669 - 10/02/17 02:16 PM Re: DIY/Home Alignment Tools - What do you use? [Re: GoodysGotaCuda]
krautrock Offline
top fuel

Registered: 01/27/03
Posts: 1752
Loc: central texas
I think the Longacre gauge I got was working fine. I bought the adapter to screw it on the spindle.

I used grease and thin metal sheet as plates...on a smooth concrete surface.

My measurements were repeating.

Top
#2380678 - 10/02/17 02:27 PM Re: DIY/Home Alignment Tools - What do you use? [Re: BigBlockMopar]
67R/T4speeder Offline
pro stock

Registered: 02/03/07
Posts: 1520
Loc: Pismo Beach,California
_________________________
Andy








www.troxellsgarage.com

Top
#2381053 - 10/02/17 11:52 PM Re: DIY/Home Alignment Tools - What do you use? [Re: GoodysGotaCuda]
tahoechallenge Offline
enthusiast

Registered: 08/19/05
Posts: 305
Loc: Kings Beach, CA
I use Fastrax. After using it for a few years, I think I am finally good at it. The key is repeatability. If you are not measuring the same way each time, the measurements you get are useless. I use a few pieces of greased Plexiglas for turn plates. I use two tape measures and tire tread for toe.

Top
#2387388 - 10/14/17 02:23 PM Re: DIY/Home Alignment Tools - What do you use? [Re: GoodysGotaCuda]
John_Kunkel Online   content
I Live Here

Registered: 01/20/03
Posts: 19588
Loc: Rio Linda, CA
I have the Tenhulzen setup, a couple of slick plastic bags under the tires acts as a cheapo swivel plate.

https://www.youtube.com/watch?annotation...p;v=ZIUUAW5KyWk
_________________________
I'm supposed to respect my elders, but its getting harder and harder for me to find one now.

Top
#2387412 - 10/14/17 02:57 PM Re: DIY/Home Alignment Tools - What do you use? [Re: John_Kunkel]
GoodysGotaCuda Online   penguin-006
5.7L Hemi, 6spd

Registered: 11/23/04
Posts: 24358
Loc: Texas
Originally Posted By John_Kunkel
I have the Tenhulzen setup, a couple of slick plastic bags under the tires acts as a cheapo swivel plate.

https://www.youtube.com/watch?annotation...p;v=ZIUUAW5KyWk


Looks like a pretty nice system, priced well too. I like the simplicity of the wheel mount, have you had any issues with it coming off of the wheel with only two contact points?
_________________________
1972 Barracuda - 5.7L Hemi, T56 Magnum 6spd - Build page -> https://www.facebook.com/GoodysGotaHemi<-
1976 Dodge Warlock - "Her Truck" - 360/727 2wd
1969 Dodge Dart Custom Sedan - Grandma Edition - 318/904
2016 Subaru WRX - E30 Tune ~320whp

Top
#2388442 - 10/16/17 09:00 PM Re: DIY/Home Alignment Tools - What do you use? [Re: GoodysGotaCuda]
Skeptic Online   tonguue
master

Registered: 01/20/03
Posts: 4252
Loc: The Pale Blue Dot
Does anybody know of a good Android app?
_________________________
"Talking tough is easy when it's other people's evil and you're judging what they do or don't believe" Mike Cooley / Drive-By Truckers Razor and Tie Music (BMI)

Top
#2440390 - 01/25/18 12:20 AM Re: DIY/Home Alignment Tools - What do you use? [Re: John_Kunkel]
GoodysGotaCuda Online   penguin-006
5.7L Hemi, 6spd

Registered: 11/23/04
Posts: 24358
Loc: Texas
Originally Posted By John_Kunkel
I have the Tenhulzen setup, a couple of slick plastic bags under the tires acts as a cheapo swivel plate.

https://www.youtube.com/watch?annotation...p;v=ZIUUAW5KyWk


For what it's worth, i bought this setup and was able to align my car over the last week or so. Once I made a few adjustments, I was able to figure out how to get repetitive readings and setup the car. I need to make a slight toe tweak to align the steering wheel, but the initial drive was very good.

For the money invested and how often I will use it, I don't have many complaints. There are a couple of things I would like to improve, but it's a pretty good bank-for-buck. I paid $192 shipped


Attachments
26165642_1768904746486909_850124230056571804_n-3.jpg


_________________________
1972 Barracuda - 5.7L Hemi, T56 Magnum 6spd - Build page -> https://www.facebook.com/GoodysGotaHemi<-
1976 Dodge Warlock - "Her Truck" - 360/727 2wd
1969 Dodge Dart Custom Sedan - Grandma Edition - 318/904
2016 Subaru WRX - E30 Tune ~320whp

Top
#2440401 - 01/25/18 12:45 AM Re: DIY/Home Alignment Tools - What do you use? [Re: GoodysGotaCuda]
RylisPro Offline


Registered: 06/18/07
Posts: 2328
Loc: NorCal
That's pretty cool and not too expensive either!
2 alignments and it pays for itself!
_________________________

/Drive
Instagram: @rylispro
YouTube:RylisPro
www.rylispro.com
925-214-9192
Tremec T56 Magnums & Quick Time bells
Lightened Billet Steel Flywheels
Prefix Performance

Top
#2440412 - 01/25/18 01:21 AM Re: DIY/Home Alignment Tools - What do you use? [Re: RylisPro]
GoodysGotaCuda Online   penguin-006
5.7L Hemi, 6spd

Registered: 11/23/04
Posts: 24358
Loc: Texas
Originally Posted By RylisPro
That's pretty cool and not too expensive either!
2 alignments and it pays for itself!


Probably one alignment, given I have the [horrid] old style Hotchkis upper control arms. Man, those things are a pain to adjust...I am doing a whole front end job on my Father-in-Laws Li'l Red Express and my Warlock will be close behind it. Also, it goes down to 13" wheels, so I can align my old FSAE car. I'll put it to use!

Naturally, the on-car adjustment version came out just a couple of months after I bought my set. spank
_________________________
1972 Barracuda - 5.7L Hemi, T56 Magnum 6spd - Build page -> https://www.facebook.com/GoodysGotaHemi<-
1976 Dodge Warlock - "Her Truck" - 360/727 2wd
1969 Dodge Dart Custom Sedan - Grandma Edition - 318/904
2016 Subaru WRX - E30 Tune ~320whp

Top
#2442707 - 01/29/18 12:43 AM Re: DIY/Home Alignment Tools - What do you use? [Re: GoodysGotaCuda]
astjp2 Offline
master

Registered: 01/18/11
Posts: 4174
Loc: Utah and Alaska
_________________________
1941 Taylorcraft
1968 Charger
1994 Wrangler
1998 Wrangler
2008 Kia Rio
2017 Jetta

I didn't do 4 years and 9 months of Graduate School to be called Mister!

Top
#2442851 - 01/29/18 10:37 AM Re: DIY/Home Alignment Tools - What do you use? [Re: astjp2]
moparx Offline
Dreaming of implants

Registered: 09/03/03
Posts: 9168
Loc: north of coder
i just restored a pair of alignment turntables i got at a swap for $25. needed new bearings [38 7/16" balls] and a lot of rust blasting. luckily, the bearing races were in great condition, as the old grease had petrified and protected the races. the angle indicator plates cleaned up very well by careful cleaning, and did not require re-painting the lines and numbers. paint, and they look very good, plus they move very smooth in all directions now ! they were locked up when i purchased them. i'll see if i can grab a pic today. these are very simple items mechanically, so if you see a set at the swaps, and can get 'em relatively cheap, don't be afraid to tackle a re-build.
beer

Top
Page 1 of 2 1 2 >

Advertisement
Forum Stats
25,489 Registered Members
32 Forums
193,038 Topics
2,253,386 Posts

Most users ever online: 1,424 @ 06/20/18 07:18 PM
Moparts Newest Topics
Vintage dual quad Edelbrock small block aluminum manifold
by Alaskan_TA
09/22/18 03:22 PM
Tire date codes, can someone decode these for me?
by RV2
09/22/18 02:53 PM
rear sway bar in Cuda with Dana 60
by FJ6AAR
09/22/18 02:11 PM
70 Challenger passenger rear 1/4 patch panel
by RROD
09/22/18 01:08 PM