changing the 3rd member cost? - Moparts Forums

Register Log In Moparts Forums Moparts Question and Answer changing the 3rd member cost?

Print Thread

changing the 3rd member cost? #1214762 04/12/12 11:53 AM 04/12/12 11:53 AM
Joined: Jun 2011 Posts: 1,039 ALBERTA CANADA C CUDA8U OP super stock
CUDA8U OP super stock C Joined: Jun 2011 Posts: 1,039 ALBERTA CANADA	what's the typical cost to change out the third member on a 742 case? these 4:11's are just too low and i'm not ready to dump $3000 into an OD tranny yet.I'm thinking a 3:55 yukon 3rd member as recommended by a mopar race guy would work

Re: changing the 3rd member cost? [Re: CUDA8U] #1214763 04/12/12 01:38 PM 04/12/12 01:38 PM
Joined: Aug 2003 Posts: 12,291 Kent, Wa 340SHORTY Truck Nut
340SHORTY Truck Nut Joined: Aug 2003 Posts: 12,291 Kent, Wa	call Dr Diff here on the board. He IS the rearend wizzard. He will set you straight and you wont find a better person to give advise.. I am truckless..

Re: changing the 3rd member cost? [Re: 340SHORTY] #1214764 04/12/12 06:28 PM 04/12/12 06:28 PM
Joined: Feb 2010 Posts: 2,806 Northern NJ StukaJU87 master
StukaJU87 master Joined: Feb 2010 Posts: 2,806 Northern NJ	Quote: He IS the rearend wizzard. Taken out of context, this statement takes on a whole new meaning. Scott 1969 Super Bee, 383/4 speed

Re: changing the 3rd member cost? [Re: StukaJU87] #1214765 04/12/12 08:11 PM 04/12/12 08:11 PM
Joined: Nov 2007 Posts: 21,822 Kirkland, Washington Pacnorthcuda Too Many Posts
Pacnorthcuda Too Many Posts Joined: Nov 2007 Posts: 21,822 Kirkland, Washington	Quote: Quote: He IS the rearend wizzard. Taken out of context, this statement takes on a whole new meaning. keep your pinion to yourself!

Re: changing the 3rd member cost? [Re: CUDA8U] #1214766 04/12/12 09:53 PM 04/12/12 09:53 PM
Joined: Jul 2003 Posts: 3,377 Rancho Cordova, CA Exit1965 master
Exit1965 master Joined: Jul 2003 Posts: 3,377 Rancho Cordova, CA	I think with all new parts, around $1350. Used ones with suregrip seem to go for $500+ easily. Changing gears is the cost of gears (250 to be safe) + install kit (figure $40 min) + about $250 to set them up and assemble/rebuild, + bearing $ if needed. If you know someone with a press who is knowledgeable, you can save the $$ on the labor and you'd just be out the $$ for gears and bearings and install kit.

Re: changing the 3rd member cost? [Re: Exit1965] #1214767 04/12/12 10:02 PM 04/12/12 10:02 PM
Joined: Jun 2011 Posts: 1,039 ALBERTA CANADA C CUDA8U OP super stock
CUDA8U OP super stock C Joined: Jun 2011 Posts: 1,039 ALBERTA CANADA	thanks,i have a complete set 3:23 and this 4:11 set that's nearly new i could sell to cover the cost,also that cost estimate is getting close to 50% of the cost of an over drive tranny

Re: changing the 3rd member cost? [Re: CUDA8U] #1214768 04/12/12 10:21 PM 04/12/12 10:21 PM
Joined: Jan 2003 Posts: 9,826 las vegas 70AARcuda master
70AARcuda master Joined: Jan 2003 Posts: 9,826 las vegas	you just want to change the ring and pinion from the 4.10 to 3.55??? I usually pay 2 hrs of shop time plus any parts..pinion seal... about 175.00 dollars... Is that your question? Tony 70 AARCuda Vitamin C 71 Dart Swinger 360 10.318 @ 128.22(10-04-14 Bakersfield) 71 Demon 360 10.666 @122.41 (01-29-17 @ Las Vegas) 71 Duster 408 (10.29 @ 127.86 3/16/19 Las Vegas)

Re: changing the 3rd member cost? [Re: 70AARcuda] #1214769 04/13/12 01:31 AM 04/13/12 01:31 AM
Joined: Jun 2011 Posts: 1,039 ALBERTA CANADA C CUDA8U OP super stock
CUDA8U OP super stock C Joined: Jun 2011 Posts: 1,039 ALBERTA CANADA	Well i'm not sure what direction i want to go ,i like the bottom end power but would like a overdrive for the highway or higher gears

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1