w-8 stainless header flanges - Moparts Forums

Register Log In Moparts Forums Unlawfl's Race & Engine Tech w-8 stainless header flanges

Print Thread

Page 1 of 2

1

2

w-8 stainless header flanges #1124203 11/29/11 06:12 PM 11/29/11 06:12 PM
Joined: May 2008 Posts: 1,238 North Cackilacky S sdaurity OP pro stock
sdaurity OP pro stock S Joined: May 2008 Posts: 1,238 North Cackilacky	Have done a few searches with no luck, I know it has been discussed before but I'm not having any luck finding any info. Thanks One day I will have something cool here.

Re: w-8 stainless header flanges [Re: sdaurity] #1124204 11/29/11 06:56 PM 11/29/11 06:56 PM
Joined: Nov 2007 Posts: 1,600 Alberta Canada StrokerAspen top fuel
StrokerAspen top fuel Joined: Nov 2007 Posts: 1,600 Alberta Canada	I remember seeing something about them too a while back. If nothing turns up, I can make them for you. Laser. Or water cut. -Kenny

Re: w-8 stainless header flanges [Re: StrokerAspen] #1124205 11/29/11 07:27 PM 11/29/11 07:27 PM
Joined: Oct 2005 Posts: 268 South Central Pa webemopes enthusiast
webemopes enthusiast Joined: Oct 2005 Posts: 268 South Central Pa	Check with spd.they had them in 3/8 and 1/2 inch.Kenny

Re: w-8 stainless header flanges [Re: StrokerAspen] #1124206 11/29/11 07:29 PM 11/29/11 07:29 PM
Joined: Mar 2010 Posts: 601 Niles, Michigan Hitman340 mopar
Hitman340 mopar Joined: Mar 2010 Posts: 601 Niles, Michigan	Bobs Pro Fab is getting ready to water jet a set for me soon.Im going 3/8 304 stainless flanges.You may want to give him a shout. Last edited by Hitman340; 11/29/11 07:31 PM. jeffallisonms@yahoo.com

Re: w-8 stainless header flanges [Re: Hitman340] #1124207 11/29/11 08:53 PM 11/29/11 08:53 PM
Joined: Nov 2009 Posts: 3,082 St. Paul , Mn. tubtar master
tubtar master Joined: Nov 2009 Posts: 3,082 St. Paul , Mn.	http://spdexhaust.com/MoparB.html# I had to send them a tracing of my port to get the right ones for my W-9 , they had them in stock.

Re: w-8 stainless header flanges [Re: tubtar] #1124208 11/29/11 09:34 PM 11/29/11 09:34 PM
Joined: Jan 2003 Posts: 2,813 Blue Ridge, VA Plumb Wired master
Plumb Wired master Joined: Jan 2003 Posts: 2,813 Blue Ridge, VA	SPD here as well. Mike Gray RIP Monte Smith aka: OutlawFish '98 Bickel Dodge Dakota PST

Re: w-8 stainless header flanges [Re: sdaurity] #1124209 11/29/11 09:37 PM 11/29/11 09:37 PM
Joined: Jan 2003 Posts: 31,050 Oregon A AndyF I Win
AndyF I Win A Joined: Jan 2003 Posts: 31,050 Oregon	Schoenfeld has most of the W head flanges. http://www.schoenfeldheaders.com/mflanges.htm

Re: w-8 stainless header flanges [Re: AndyF] #1124210 11/29/11 10:45 PM 11/29/11 10:45 PM
Joined: Nov 2009 Posts: 3,082 St. Paul , Mn. tubtar master
tubtar master Joined: Nov 2009 Posts: 3,082 St. Paul , Mn.	Quote: Schoenfeld has most of the W head flanges. http://www.schoenfeldheaders.com/mflanges.htm At 29.00 a pop , I'd bet them ain't stainless.

Re: w-8 stainless header flanges [Re: Plumb Wired] #1124211 11/30/11 01:33 PM 11/30/11 01:33 PM
Joined: Nov 2007 Posts: 1,600 Alberta Canada StrokerAspen top fuel
StrokerAspen top fuel Joined: Nov 2007 Posts: 1,600 Alberta Canada	Quote: SPD here as well. Mike Gray How much do the SPD flanges go for typically? -Kenny

Re: w-8 stainless header flanges [Re: tubtar] #1124212 11/30/11 02:24 PM 11/30/11 02:24 PM
Joined: Jun 2003 Posts: 52,972 Romeo MI MR_P_BODY Master
MR_P_BODY Master Joined: Jun 2003 Posts: 52,972 Romeo MI	Quote: Quote: Schoenfeld has most of the W head flanges. http://www.schoenfeldheaders.com/mflanges.htm At 29.00 a pop , I'd bet them ain't stainless. Plus they're 1/4" thick... I'd never use 1/4

Re: w-8 stainless header flanges [Re: StrokerAspen] #1124213 11/30/11 02:39 PM 11/30/11 02:39 PM
Joined: Nov 2009 Posts: 3,082 St. Paul , Mn. tubtar master
tubtar master Joined: Nov 2009 Posts: 3,082 St. Paul , Mn.	Quote: Quote: SPD here as well. Mike Gray How much do the SPD flanges go for typically? -Kenny Mine were 178.00 a pair shipped to Mn. This was a year ago or so. 160.00 for the parts , 18.00 for the ride

Re: w-8 stainless header flanges [Re: tubtar] #1124214 11/30/11 03:11 PM 11/30/11 03:11 PM
Joined: Jan 2003 Posts: 2,813 Blue Ridge, VA Plumb Wired master
Plumb Wired master Joined: Jan 2003 Posts: 2,813 Blue Ridge, VA	Quote: Quote: Quote: SPD here as well. Mike Gray How much do the SPD flanges go for typically? -Kenny Mine were 178.00 a pair shipped to Mn. This was a year ago or so. 160.00 for the parts , 18.00 for the ride Sounds about right on the pricing. I can't locate my last invoice from SPD. Be careful on SPD's website they have the W8 flanges reversed as far as description. The Nascar W8's have the 4.75" bolt spacing on the center flange and the CFE Drag Race W8's have the 4.96" bolt spacing. If you are not sure you can lay a sheet of paper over the port and do a rubbing and fax to them. For Coleman/Arrington W8's I have ordered basic part number M88325. Mike Gray RIP Monte Smith aka: OutlawFish '98 Bickel Dodge Dakota PST

Re: w-8 stainless header flanges [Re: Plumb Wired] #1124215 11/30/11 03:24 PM 11/30/11 03:24 PM
Joined: May 2007 Posts: 636 Central,Ohio FASTFISH420 mopar
FASTFISH420 mopar Joined: May 2007 Posts: 636 Central,Ohio	Quote: Quote: Quote: Quote: SPD here as well. Mike Gray How much do the SPD flanges go for typically? -Kenny Mine were 178.00 a pair shipped to Mn. This was a year ago or so. 160.00 for the parts , 18.00 for the ride Sounds about right on the pricing. I can't locate my last invoice from SPD. Be careful on SPD's website they have the W8 flanges reversed as far as description. The Nascar W8's have the 4.75" bolt spacing on the center flange and the CFE Drag Race W8's have the 4.96" bolt spacing. If you are not sure you can lay a sheet of paper over the port and do a rubbing and fax to them. For Coleman/Arrington W8's I have ordered basic part number M88325. Mike Gray Yeah Mike you are right.I have the SPD as well 1969 Barracuda 8 second all/motor small block 2014 Shelby GT500 Mustang Uratchko Racing Engines www.URE-RACING.com

Re: w-8 stainless header flanges [Re: FASTFISH420] #1124216 11/30/11 05:12 PM 11/30/11 05:12 PM
Joined: Nov 2007 Posts: 1,600 Alberta Canada StrokerAspen top fuel
StrokerAspen top fuel Joined: Nov 2007 Posts: 1,600 Alberta Canada	That's a pretty decent price I would say for a set of waterjet flanges. I wonder if Laser cut would be any cheaper? If anyone is interested, I could draw up some and get a price together. -Kenny

Re: w-8 stainless header flanges [Re: StrokerAspen] #1124217 11/30/11 05:43 PM 11/30/11 05:43 PM
Joined: Feb 2009 Posts: 1,019 Finland mafo super stock
mafo super stock Joined: Feb 2009 Posts: 1,019 Finland	I have drawings if needed, can trade for one set of flanges -65 Valiant,420", all motor,2700#, dot tires, 8,42 @ 160,2

Re: w-8 stainless header flanges [Re: mafo] #1124218 11/30/11 11:08 PM 11/30/11 11:08 PM
Joined: Jan 2003 Posts: 6,146 Melbourne , Australia LA360 master
LA360 master Joined: Jan 2003 Posts: 6,146 Melbourne , Australia	That could be arranged Ken lol Alan Jones

Re: w-8 stainless header flanges [Re: LA360] #1124219 11/30/11 11:49 PM 11/30/11 11:49 PM
Joined: Nov 2007 Posts: 1,600 Alberta Canada StrokerAspen top fuel
StrokerAspen top fuel Joined: Nov 2007 Posts: 1,600 Alberta Canada	I have a few different sets of flanges I need to do. A set for a B1 TS, another set for a set of RR Oldsmobile heads.... I should get a list going, maybe a group buy on a bunch of different laser cut flanges.... Hmmmm..... -Kenny

Re: w-8 stainless header flanges [Re: StrokerAspen] #1124220 12/01/11 01:45 AM 12/01/11 01:45 AM
Joined: Feb 2003 Posts: 3,456 Out West 4 408strokerdart master
408strokerdart master 4 Joined: Feb 2003 Posts: 3,456 Out West	Quote: I have a few different sets of flanges I need to do. A set for a B1 TS, another set for a set of RR Oldsmobile heads.... I should get a list going, maybe a group buy on a bunch of different laser cut flanges.... Hmmmm..... -Kenny Are we talking Craftsman Truck W8's or CFE W8's? Pattern is different. I could use a set of SS flanges for my Coleman W8s.

Re: w-8 stainless header flanges [Re: 408strokerdart] #1124221 12/01/11 02:39 AM 12/01/11 02:39 AM
Joined: Jan 2003 Posts: 3,505 DFW M mr_340 master
mr_340 master M Joined: Jan 2003 Posts: 3,505 DFW	If you are going to get several sets water jet cut, I'd try to get 304L or 316L SS. It is preferred for welded components. http://www.finishing.com/160/07.shtml Floyd Lippencott IV

Re: w-8 stainless header flanges [Re: mr_340] #1124222 12/01/11 02:57 AM 12/01/11 02:57 AM
Joined: Feb 2009 Posts: 1,019 Finland mafo super stock
mafo super stock Joined: Feb 2009 Posts: 1,019 Finland	CFE here -65 Valiant,420", all motor,2700#, dot tires, 8,42 @ 160,2

Page 1 of 2

1

2

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1