|
Re: neutral safety switch wiring harness
[Re: Challenger 1]
#1070235
09/06/11 01:59 PM
09/06/11 01:59 PM
|
Joined: Jul 2005
Posts: 1,169
Richmond, VA
rayztoy
super stock
|
super stock
Joined: Jul 2005
Posts: 1,169
Richmond, VA
|
Quote:
On my 71 e body it is the lower left connector on my fuse block looking at it from the engine compartment. It also has the windshield wiper motor wires in it also. 4 wire plug.
Hello Gary,
Could you post a pic of the harness running along the firewall to the fuse block? Also, could you post a pic showing where the harness from the dash reverse light routes under the dash and where it connects to? TIA
Ray 
|
|
|
Re: neutral safety switch wiring harness
[Re: rayztoy]
#1070239
09/08/11 07:51 PM
09/08/11 07:51 PM
|
Joined: Oct 2006
Posts: 7,363
Iowa
burdar
Owen's Dad
|
Owen's Dad
Joined: Oct 2006
Posts: 7,363
Iowa
|
I have this detail on file and thought it would help.
After the harness comes off the trans, it goes through one black plastic circular shaped wire strap on the firewall.(this is on a 73...I think earlier years used a either a black or white "D" shaped strap) From there it runs accross the firewall and connects to the lower lefthand corner of the bulkhead connector. It only goes through the one strap on the firewall...the one below the voltage regulator. If you want me to take a pic let me know.
Last edited by burdar; 09/08/11 08:01 PM.
|
|
|
Re: neutral safety switch wiring harness
[Re: burdar]
#1070242
09/08/11 08:42 PM
09/08/11 08:42 PM
|
Joined: Jul 2005
Posts: 1,169
Richmond, VA
rayztoy
super stock
|
super stock
Joined: Jul 2005
Posts: 1,169
Richmond, VA
|
Darren, Thanks for that info.  I believe my 70 cuda should be the same. A pic would be helpful. I need the routing from the dash light under the dash to where it connects to... Ray
|
|
|
Re: neutral safety switch wiring harness
[Re: rayztoy]
#1070244
09/09/11 07:53 AM
09/09/11 07:53 AM
|
Joined: Jan 2003
Posts: 74,976
U.S.S.A.
JohnRR
I Win
|
I Win
Joined: Jan 2003
Posts: 74,976
U.S.S.A.
|
Quote:
Darren,
Thanks for that info. I believe my 70 cuda should be the same. A pic would be helpful. I need the routing from the dash light under the dash to where it connects to...
Ray
It goes to the wiring bulkhead , should be pretty easy to figure out where it goes , the wire is only so long , taped in a few spots to hold it to the harness . The harness from the trans when it gets to the firewall is held by the same clips that hold the engine harness .
|
|
|
Re: neutral safety switch wiring harness
[Re: JohnRR]
#1070245
09/09/11 11:23 AM
09/09/11 11:23 AM
|
Joined: Feb 2005
Posts: 28,312
Cincinnati, Ohio
Challenger 1
Too Many Posts
|
Too Many Posts
Joined: Feb 2005
Posts: 28,312
Cincinnati, Ohio
|
Quote:
Quote:
Darren,
Thanks for that info. I believe my 70 cuda should be the same. A pic would be helpful. I need the routing from the dash light under the dash to where it connects to...
Ray
It goes to the wiring bulkhead , should be pretty easy to figure out where it goes , the wire is only so long , taped in a few spots to hold it to the harness . The harness from the trans when it gets to the firewall is held by the same clips that hold the engine harness .
Yup easy to figure how it routes, it can only go one way.
|
|
|
Re: neutral safety switch wiring harness
[Re: Challenger 1]
#1070246
09/09/11 12:03 PM
09/09/11 12:03 PM
|
Joined: Jul 2005
Posts: 1,169
Richmond, VA
rayztoy
super stock
|
super stock
Joined: Jul 2005
Posts: 1,169
Richmond, VA
|
Gents,
Thanks for the previous posts. The harness from the reverse light switch appears to be short as it will mount on the drivers side top bellhousing bolt, not the passenger side top bellhousing bolt, and directly runs to the fuse box via metal tabs on the fiewall. It will not reach the engine compartment harness plastic loops. The harness on the reverse light is just hanging there, and I'm not sure where it connects to. Does it go to the fuse block in the interior side, or does it connect to the main dash harness, or go through the firewall to connect to the engine harness? Any help is appreciated. The reverse lights don't work, so I'm trying to fix them. TIA
Ray
|
|
|
Re: neutral safety switch wiring harness
[Re: rayztoy]
#1070247
09/12/11 10:38 AM
09/12/11 10:38 AM
|
Joined: Jan 2003
Posts: 74,976
U.S.S.A.
JohnRR
I Win
|
I Win
Joined: Jan 2003
Posts: 74,976
U.S.S.A.
|
Quote:
Gents,
Thanks for the previous posts. The harness from the reverse light switch appears to be short as it will mount on the drivers side top bellhousing bolt, not the passenger side top bellhousing bolt, and directly runs to the fuse box. It will not reach the engine compartment harness plastic loops. The harness on the reverse light is just hanging there, and I'm not sure where it connects to. Does it go to the fuse block in the interior side, or does it connect to the main dash harness, or go through the firewall to connect to the engine harness? Any help is appreciated. The reverse lights don't work, so I'm trying to fix them. TIA
Ray
Since your car is a 73 I can't say what was done then , I can only comment on 1969-70 A/B body which went to the bulkhead directly and the reverse light harness was held to the firewall by the rubber tipped metal clips welded to the firewall not the plastic loop clips on the inner fender panels.
Do you have the service manual for your car ? there is a wealth of information in it , like wiring diagrams ...
|
|
|
Re: neutral safety switch wiring harness
[Re: JohnRR]
#1070248
09/12/11 12:29 PM
09/12/11 12:29 PM
|
Joined: Oct 2006
Posts: 7,363
Iowa
burdar
Owen's Dad
|
Owen's Dad
Joined: Oct 2006
Posts: 7,363
Iowa
|
|
|
|
Re: neutral safety switch wiring harness
[Re: burdar]
#1070249
09/12/11 01:17 PM
09/12/11 01:17 PM
|
Joined: Jan 2003
Posts: 74,976
U.S.S.A.
JohnRR
I Win
|
I Win
Joined: Jan 2003
Posts: 74,976
U.S.S.A.
|
Quote:
His car is a 1970.
The confusion on my part is the subject is asking about a 69 B body , we have an answer about a 71 E body and more questions about a 70 E body ...
|
|
|
Re: neutral safety switch wiring harness
[Re: rayztoy]
#1070251
09/12/11 05:11 PM
09/12/11 05:11 PM
|
Joined: Jan 2003
Posts: 74,976
U.S.S.A.
JohnRR
I Win
|
I Win
Joined: Jan 2003
Posts: 74,976
U.S.S.A.
|
Quote:
John and fellow members,
I apologize for the confusion with the questions relating to my 70 cuda. The thread was initially for the B body and it was answered. Instead of starting another thread, I just thought I could ask some questions about the 70 e body.
Ray
It would probably get you your answer faster if you just did a new thread . 
|
|
|
Re: neutral safety switch wiring harness
[Re: JohnRR]
#1070253
09/12/11 07:47 PM
09/12/11 07:47 PM
|
Joined: Jul 2005
Posts: 1,169
Richmond, VA
rayztoy
super stock
|
super stock
Joined: Jul 2005
Posts: 1,169
Richmond, VA
|
It would probably get you your answer faster if you just did a new thread .
 with you John.
Ray
|
|
|
|
|
Thanks! 
ok,on my -70 cuda theres a hole in the firewall,just above or under? the road-lamp grommet coming into the engine compartment.anyway you will see witch hole it is when you look into the engine room as your missing your harness,i have not looked closer into where it routes under the dash,but believes? it goes straight to the b-u lamp on the dash.in the engine compartment side on my car on the firewall is a barrel shaped grommet with the b-u cable sticking out of it a few inches with a connector on it,witch then connects to something,maybe the single connector cable coming from the wipermotor cavity in the connectorthing on the firewall.overandout 
![6817085-6478266-70E-BodyBackupLightWiring[1].jpg](/ubbthreads/ubbthreads.php/ubb/download/Number/111240/filename/6817085-6478266-70E-BodyBackupLightWiring[1].jpg){kind=link}
