Re: Where to get a driveshaft for 71 Challenger?
[Re: buildanother]
#1052639
08/14/11 04:28 PM
08/14/11 04:28 PM
|
Joined: Jan 2003
Posts: 1,619 MA
ragtop
OP
top fuel
|
OP
top fuel
Joined: Jan 2003
Posts: 1,619
MA
|
Quote:
I would think that little runout could be balanced out, no?
I tried the the two hose clamp trick with no success. I also had it ballanced years ago, but they just put a small weight on the front, with no improvement. If you think about it, I would think that .025 runnout on the entire length of the shaft is a lot of weight.
|
|
|
Re: Where to get a driveshaft for 71 Challenger?
[Re: ragtop]
#1052640
08/14/11 04:30 PM
08/14/11 04:30 PM
|
Joined: Jan 2004
Posts: 27,347 Today? Who Knows?
1_WILD_RT
Management Trainee
|
Management Trainee
Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
|
Have you checked pinion angle?
"The Armies of our ancestors were lucky, in that they were not trailed by a second army of pencil pushers."
|
|
|
Re: Where to get a driveshaft for 71 Challenger?
[Re: 1_WILD_RT]
#1052641
08/14/11 06:19 PM
08/14/11 06:19 PM
|
Joined: May 2005
Posts: 4,722 Florida
BDW
master
|
master
Joined: May 2005
Posts: 4,722
Florida
|
|
|
|
Re: Where to get a driveshaft for 71 Challenger?
[Re: 1_WILD_RT]
#1052643
08/15/11 02:40 AM
08/15/11 02:40 AM
|
Joined: Jan 2003
Posts: 1,619 MA
ragtop
OP
top fuel
|
OP
top fuel
Joined: Jan 2003
Posts: 1,619
MA
|
Quote:
Have you checked pinion angle?
Yes. I have 3 degrees nose down. I had to add the wedge the springs. Thanks for the replys.
|
|
|
Re: Where to get a driveshaft for 71 Challenger?
[Re: ragtop]
#1052645
08/15/11 11:32 AM
08/15/11 11:32 AM
|
Joined: Jan 2003
Posts: 75,004 U.S.S.A.
JohnRR
I Win
|
I Win
Joined: Jan 2003
Posts: 75,004
U.S.S.A.
|
Quote:
Who sells good, true running, OEM style steel, driveshafts. My drive shaft has .025 runnout along the entire shaft. It is straight, but has linear runnout. I get a lot of vibration at 60 mph and as the speed goes up, the vibration goes up. It is a 1971 Challenger 340, auto. Manual says 45.60 long. Thanks.
There was a thread about this at one point , there is a comnpany that does them for Fords I think , they were thinking of doing them for GM but ? I have a few shafts Don , I might have one that length , I'll check this afternoon when I get home.
Otherwise it a straight tube shaft , with new joints , who are you taking the shaft to to have it check ? I use North Shore Axle in North Reading , across from Kitty's ....
|
|
|
Re: Where to get a driveshaft for 71 Challenger?
[Re: ragtop]
#1052649
08/15/11 01:36 PM
08/15/11 01:36 PM
|
Joined: Feb 2005
Posts: 28,312 Cincinnati, Ohio
Challenger 1
Too Many Posts
|
Too Many Posts
Joined: Feb 2005
Posts: 28,312
Cincinnati, Ohio
|
Quote:
There was a thread about this at one point , there is a comnpany that does them for Fords I think , they were thinking of doing them for GM but ? I have a few shafts Don , I might have one that length , I'll check this afternoon when I get home.
Otherwise it a straight tube shaft , with new joints , who are you taking the shaft to to have it check ? I use North Shore Axle in North Reading , across from Kitty's ....
Thanks John. I checked it myself with a dail indicator installed. My yoke measures 1.680 dia. and my new tail shaft bushing installed measures 1.688. why is the clearance so large?
Sounds like your yoke is worn out. imo
|
|
|
Re: Where to get a driveshaft for 71 Challenger?
[Re: Challenger 1]
#1052650
08/15/11 07:17 PM
08/15/11 07:17 PM
|
Joined: Jan 2003
Posts: 1,619 MA
ragtop
OP
top fuel
|
OP
top fuel
Joined: Jan 2003
Posts: 1,619
MA
|
Quote:
Quote:
There was a thread about this at one point , there is a comnpany that does them for Fords I think , they were thinking of doing them for GM but ? I have a few shafts Don , I might have one that length , I'll check this afternoon when I get home.
Otherwise it a straight tube shaft , with new joints , who are you taking the shaft to to have it check ? I use North Shore Axle in North Reading , across from Kitty's ....
Thanks John. I checked it myself with a dail indicator installed. My yoke measures 1.680 dia. and my new tail shaft bushing installed measures 1.688. why is the clearance so large?
Sounds like your yoke is worn out. imo
I measured the yoke and it is uniform 1.680 the entire length. I also mounted the shaft 180 degrees on the diff. pinion, and it showed the same high and low spots on the same place in the shaft. I still don't like that .008 clearance between the yoke and bushing.
|
|
|
|
|