|
Re: Torsion bars which way
[Re: txterry2]
#832818
10/18/10 01:01 PM
10/18/10 01:01 PM
|
Joined: Mar 2008
Posts: 5,746
Ontario, Canada
Dodgem
OP
master
|
OP
master
Joined: Mar 2008
Posts: 5,746
Ontario, Canada
|
Quote:
No differance between front and back.
Thanks so they don't matter which way they get twisted?? so it would not matter if they were in the right or left sides then either??
|
|
|
Re: Torsion bars which way
[Re: Dodgem]
#832819
10/18/10 01:23 PM
10/18/10 01:23 PM
|
Joined: Apr 2003
Posts: 512
Sacramento, CA
Bdrainy
mopar
|
mopar
Joined: Apr 2003
Posts: 512
Sacramento, CA
|
Quote:
Quote:
No differance between front and back.
Thanks so they don't matter which way they get twisted?? so it would not matter if they were in the right or left sides then either??
No answer for you but I have always wondered the same thing! They say there is a left and right and they need to be on the correct side, but it doesn't matter which end goes in first.
Maybe I'm slow, but that doesn't make sense to me. Putting different ends in first would make them twist in different directions...and I understand that they are made to twist in a specific direction.
I've never seen (not saying there isn't one) an explanation as to why they are not specific as to which end goes in first...
Hopefully someone can chime in.
|
|
|
Re: Torsion bars which way
[Re: Bdrainy]
#832821
10/18/10 01:46 PM
10/18/10 01:46 PM
|
Joined: Mar 2008
Posts: 5,746
Ontario, Canada
Dodgem
OP
master
|
OP
master
Joined: Mar 2008
Posts: 5,746
Ontario, Canada
|
Maybe I'm slow, but that doesn't make sense to me. Putting different ends in first would make them twist in different directions...and I understand that they are made to twist in a specific direction. I've never seen (not saying there isn't one) an explanation as to why they are not specific as to which end goes in first... Hopefully someone can chime in.
Me two Left bar in driver side end A is in the driver lower control it gets twisted counter clockwise looking from front and end B in back looking from back would be twisted clockwise.
switch around now with B end in front it would now be twisted counter clockwise and A in back would have clockwise twist???
|
|
|
Re: Torsion bars which way
[Re: Fab64]
#832824
10/18/10 08:05 PM
10/18/10 08:05 PM
|
Joined: Mar 2008
Posts: 5,746
Ontario, Canada
Dodgem
OP
master
|
OP
master
Joined: Mar 2008
Posts: 5,746
Ontario, Canada
|
Quote:
Picture putting the lid on a bottle. No matter whether you're holding the cap or the bottle in your right hand, you're still turning your right hand clockwise to tighten the lid. It's no different with the torsion bar.
But if you glued to milk bottles together at the bottom (assumimg screw on caps) and put the cap ends in a vise and turned whole thing one would tighten while the other tried to loosen???
|
|
|
Re: Torsion bars which way
[Re: buildanother]
#832826
10/18/10 08:19 PM
10/18/10 08:19 PM
|
Joined: Nov 2003
Posts: 36,041
Lincoln Nebraska
RapidRobert
Circle Track
|
Circle Track
Joined: Nov 2003
Posts: 36,041
Lincoln Nebraska
|
Put the end w the #'s/letters to the rear so later on down the line you can see it to refer to it if you forget whats in there as the front ends will be covered
live every 24 hour block of time like it's your last day on earth
|
|
|
Re: Torsion bars which way
[Re: Dodgem]
#832829
10/18/10 09:40 PM
10/18/10 09:40 PM
|
Joined: Nov 2003
Posts: 36,041
Lincoln Nebraska
RapidRobert
Circle Track
|
Circle Track
Joined: Nov 2003
Posts: 36,041
Lincoln Nebraska
|
Quote:
My T bars have numbers on both ends?? MP 920's
in that case either way end to end will work for you. Some of the real large bars (I dont know about MP ones) can even go on either side (but keep it on the same side always) as they are not marked side specific. EDIT no R or L just 920 right?
Last edited by RapidRobert; 10/18/10 09:48 PM.
live every 24 hour block of time like it's your last day on earth
|
|
|
Re: Torsion bars which way
[Re: Dodgem]
#832830
10/18/10 09:46 PM
10/18/10 09:46 PM
|
Joined: Oct 2004
Posts: 1,074
So Cal, USA
Fab64
super stock
|
super stock
Joined: Oct 2004
Posts: 1,074
So Cal, USA
|
Quote:
Quote:
Picture putting the lid on a bottle. No matter whether you're holding the cap or the bottle in your right hand, you're still turning your right hand clockwise to tighten the lid. It's no different with the torsion bar.
But if you glued to milk bottles together at the bottom (assumimg screw on caps) and put the cap ends in a vise and turned whole thing one would tighten while the other tried to loosen???
Actually, you proved my point. What I'm trying to say is that just because you swap the ends front to rear, the direction needed to tighten the lid doesn't change. Pretend the glued-together bottles are the passenger side torsion bar. The LCA is attached to one cap, and the other cap is in the torsion bar anchor. When the passenger side wheel comes up, the cap is going to tighten. Even if you swap them end for end, it will work the same way.
|
|
|
Re: Torsion bars which way
[Re: Fab64]
#832831
10/18/10 10:01 PM
10/18/10 10:01 PM
|
Joined: Nov 2003
Posts: 36,041
Lincoln Nebraska
RapidRobert
Circle Track
|
Circle Track
Joined: Nov 2003
Posts: 36,041
Lincoln Nebraska
|
If a Tbar was suspended in air & you walked up on it from the side and extended your arms and grabbed the left end w your left hand and the right end w your right hand then applied a bit of torque to each end clockwise & held it on both ends then turned (rotated) your body around halfway a half turn you'd still be applying torque to each end the same way (clockwise)so the bar would still be getting twisted the same way
live every 24 hour block of time like it's your last day on earth
|
|
|
Re: Torsion bars which way
[Re: RapidRobert]
#832833
10/20/10 01:07 PM
10/20/10 01:07 PM
|
Joined: Mar 2008
Posts: 5,746
Ontario, Canada
Dodgem
OP
master
|
OP
master
Joined: Mar 2008
Posts: 5,746
Ontario, Canada
|
Quote:
Quote:
My T bars have numbers on both ends?? MP 920's
in that case either way end to end will work for you. Some of the real large bars (I dont know about MP ones) can even go on either side (but keep it on the same side always) as they are not marked side specific. EDIT no R or L just 920 right?
No they have a full set of numbers different front and back and R and L
|
|
|
|
|
