|
Re: Let's hear some W7,W8,and W9 builds
[Re: 340_Dart]
#743297
12/29/11 06:55 PM
12/29/11 06:55 PM
|
Joined: Oct 2010
Posts: 2,408
Ambridge, Pa.
rickraw
top fuel
|
top fuel
Joined: Oct 2010
Posts: 2,408
Ambridge, Pa.
|
mine's a 440sb, 4"x 4.185 diamond pistons 11-1, w9's by ryan, 730 roller by bullet cams, callies crank, compustar rods, m1 intake, prosystems 1050 domy. best so far- 9.61@137.91 with some trans slippage. street ride. seeya.
|
|
|
Re: Let's hear some W7,W8,and W9 builds
[Re: Uncle Barry]
#743303
12/29/11 11:00 PM
12/29/11 11:00 PM
|
Joined: Nov 2004
Posts: 4,330
Lynchburg, VA
Leon441
master
|
master
Joined: Nov 2004
Posts: 4,330
Lynchburg, VA
|
Sold the CFE W8's but....
421 SB R3 358 WC block
Crower Ultralite crank 3.8" stroke
GRP rods
Diamond pistons
Bullet roller cam
Single four barrel cast intake
Best ET it ran 5.69
Best honest MPH 125 had a no name track that showed 128 but, I called BS.
The block has been tested due to an undetermined leak and no trouble was found in the questionable cylinder. The heads are sold sense then the block and intakes are in the for sale section. Could be somebodies lucky day.
Leon
Career best 8.02 @ 169 at 3050# and 10" tires small block power.
|
|
|
Re: Let's hear some W7,W8,and W9 builds
[Re: Uncle Barry]
#743304
12/29/11 11:19 PM
12/29/11 11:19 PM
|
Joined: Feb 2011
Posts: 159
australia
charger410
member
|
member
Joined: Feb 2011
Posts: 159
australia
|
Ex sprintcar engine from Us in my Chug.
410in 4.15 x 3.8 A8 block
solid roller 268/50 780lift
W9 heads, titanium valves, pac springs, jessel rockers
JE pistons
Carrilo rods
Bryant Crankshaft
Barns 4 stage dry sump
Injecter stacks
1 7/8 step into 2inch pipes
Dyno 875hp 652fbs
Been running for 4years never touched the engine besides plugs and oil
Have only done street events on slippery tracks but will take it to the local 1/4mile track and see how it goes in a week and will post my time here good or bad
Peter. Australian Charger, alloy block injected 410in, w9 na 9.03@148 leafs 3000lb
1967 barracuda 605 hemi Stage5 millennium 8.2@170
|
|
|
Re: Let's hear some W7,W8,and W9 builds
[Re: charger410]
#743305
12/30/11 11:12 AM
12/30/11 11:12 AM
|
Joined: Apr 2007
Posts: 2,028
Trumbull,CT.
jim sciortino
top fuel
|
top fuel
Joined: Apr 2007
Posts: 2,028
Trumbull,CT.
|
9" R3 3.79 Callies 4.185 bore MGP rods 13.8 static 55mm cam 15* Coleman/Arrington W8 420 intake SV-1 3 step header w/Burns merge External wet sump 894hp-657tq Built to spray a little, but decided to go N/A. Car is now finished just in time for the bad weather.  We will run this engine for one season before selling it and doing a full N/A build.
|
|
|
Re: Let's hear some W7,W8,and W9 builds
[Re: fishy340]
#743309
12/30/11 07:47 PM
12/30/11 07:47 PM
|
Joined: Nov 2004
Posts: 4,330
Lynchburg, VA
Leon441
master
|
master
Joined: Nov 2004
Posts: 4,330
Lynchburg, VA
|
Hey Jim, who makes the 55 mm cam core?
Leon
Career best 8.02 @ 169 at 3050# and 10" tires small block power.
|
|
|
Re: Let's hear some W7,W8,and W9 builds
[Re: fishy340]
#743310
12/31/11 09:52 AM
12/31/11 09:52 AM
|
Joined: Apr 2007
Posts: 2,028
Trumbull,CT.
jim sciortino
top fuel
|
top fuel
Joined: Apr 2007
Posts: 2,028
Trumbull,CT.
|
Quote:
very impressive boys! and jim you can put your motor on the ferry i'll pick it up on the other side somewhere in suffolk county 
Go to an ATCO rent day and take it right out of the car. 
|
|
|
Re: Let's hear some W7,W8,and W9 builds
[Re: Leon441]
#743311
12/31/11 09:55 AM
12/31/11 09:55 AM
|
Joined: Apr 2007
Posts: 2,028
Trumbull,CT.
jim sciortino
top fuel
|
top fuel
Joined: Apr 2007
Posts: 2,028
Trumbull,CT.
|
Quote:
Hey Jim, who makes the 55 mm cam core?
Leon
Dean just gave me a slap. It's a 50mm.
I should really re-read before I post.
|
|
|
Re: Let's hear some W7,W8,and W9 builds
[Re: jim sciortino]
#743312
12/31/11 04:13 PM
12/31/11 04:13 PM
|
Joined: Feb 2003
Posts: 3,456
Out West
408strokerdart
master
|
master
Joined: Feb 2003
Posts: 3,456
Out West
|
Quote:
9" R3
3.79 Callies
4.185 bore
MGP rods
13.8 static
55mm cam
15* Coleman/Arrington W8
420 intake
SV-1
3 step header w/Burns merge
External wet sump
894hp-657tq
Built to spray a little, but decided to go N/A. Car is now finished just in time for the bad weather. We will run this engine for one season before selling it and doing a full N/A build.
Almost a clone to mine....why is mine such a turd by comparison? Hey Jim, could you share some cam/valvetrain specs on your build? PM if you want. No offense to any others, but this an impressive build for the power output. I am sure I am 100 hp less with almost the same combo and more compression. 
|
|
|
Re: Let's hear some W7,W8,and W9 builds
[Re: 408strokerdart]
#743313
12/31/11 07:37 PM
12/31/11 07:37 PM
|
Joined: Jan 2003
Posts: 2,813
Blue Ridge, VA
Plumb Wired
master
|
master
Joined: Jan 2003
Posts: 2,813
Blue Ridge, VA
|
Quote:
Quote:
9" R3
3.79 Callies
4.185 bore
MGP rods
13.8 static
55mm cam
15* Coleman/Arrington W8
420 intake
SV-1
3 step header w/Burns merge
External wet sump
894hp-657tq
Built to spray a little, but decided to go N/A. Car is now finished just in time for the bad weather. We will run this engine for one season before selling it and doing a full N/A build.
Almost a clone to mine....why is mine such a turd by comparison? Hey Jim, could you share some cam/valvetrain specs on your build? PM if you want. No offense to any others, but this an impressive build for the power output. I am sure I am 100 hp less with almost the same combo and more compression.
Brian, I was thinking the same thing. Mine is very similar as well. I'm sure my combo is giving up some hp with the nitrous camshaft but 100 hp?
Mike Gray
Last edited by OutlawFish; 12/31/11 07:38 PM.
RIP Monte Smith
aka: OutlawFish
'98 Bickel Dodge Dakota PST
|
|
|
Re: Let's hear some W7,W8,and W9 builds
[Re: Plumb Wired]
#743314
12/31/11 09:07 PM
12/31/11 09:07 PM
|
Joined: Feb 2003
Posts: 3,456
Out West
408strokerdart
master
|
master
Joined: Feb 2003
Posts: 3,456
Out West
|
Quote:
Quote:
Quote:
9" R3
3.79 Callies
4.185 bore
MGP rods
13.8 static
55mm cam
15* Coleman/Arrington W8
420 intake
SV-1
3 step header w/Burns merge
External wet sump
894hp-657tq
Built to spray a little, but decided to go N/A. Car is now finished just in time for the bad weather. We will run this engine for one season before selling it and doing a full N/A build.
Almost a clone to mine....why is mine such a turd by comparison? Hey Jim, could you share some cam/valvetrain specs on your build? PM if you want. No offense to any others, but this an impressive build for the power output. I am sure I am 100 hp less with almost the same combo and more compression.
Brian, I was thinking the same thing. Mine is very similar as well. I'm sure my combo is giving up some hp with the nitrous camshaft but 100 hp?
Mike Gray
Yes Mike....ours are very similar as well. What is Jim doing so right that we are doing so wrong for the difference in hp? I can understand mine being slightly quicker than yours in (N/A) because I don't have a nitrous cam, but ours are pretty equally paired. I know Jim has beaten on his on the dyno for a long time and is wringing it out pretty good.
|
|
|
Re: Let's hear some W7,W8,and W9 builds
[Re: 408strokerdart]
#743316
01/01/12 06:59 AM
01/01/12 06:59 AM
|
Joined: Jan 2003
Posts: 426
Cairns Queensland Australia. T...
vc360
mopar
|
mopar
Joined: Jan 2003
Posts: 426
Cairns Queensland Australia. T...
|
Quote:
Quote:
9" R3
3.79 Callies
4.185 bore
MGP rods
13.8 static
55mm cam
15* Coleman/Arrington W8
420 intake
SV-1
3 step header w/Burns merge
External wet sump
894hp-657tq
Built to spray a little, but decided to go N/A. Car is now finished just in time for the bad weather. We will run this engine for one season before selling it and doing a full N/A build.
Almost a clone to mine....why is mine such a turd by comparison? Hey Jim, could you share some cam/valvetrain specs on your build? PM if you want. No offense to any others, but this an impressive build for the power output. I am sure I am 100 hp less with almost the same combo and more compression.
I would say cylinder head/manifold/carb. Mine picked up 100hp with a head change and another 30 after the dyno with more carb work.
4.100 x 4.00 stroke Chapman w9 with 772 intake opened for a dominator. 754hp/615ftlbs. In my 3520lb barracuda has run a best of 9.66 at 138.6mph.
|
|
|
|
|
