|
Re: Holley 4150 fuel lines, Whats your setup?
[Re: 440challenger]
#537381
11/26/09 03:55 PM
11/26/09 03:55 PM
|
Joined: Dec 2007
Posts: 10,542
BROOK PARK, OH
WILD BILL
Senior Member of the Junior Dragster Club
|
Senior Member of the Junior Dragster Club
Joined: Dec 2007
Posts: 10,542
BROOK PARK, OH
|
Quote:
Really was trying to stay away from AN fittings and braided line. Thanks!
Well, that shuts me up 
|
|
|
Re: Holley 4150 fuel lines, Whats your setup?
[Re: Pacnorthcuda]
#537382
11/26/09 03:58 PM
11/26/09 03:58 PM
|
Joined: Feb 2003
Posts: 4,503
NJ
440challenger
OP
master
|
OP
master
Joined: Feb 2003
Posts: 4,503
NJ
|
Quote:
On mine I flipped the "t" to the carb around (so it faces the firewall) and ran hard line from the mechanical pump along the frame rail (basically reversing the path of the tank-to-pump line and then went up the firewall and connected.
Its very sanitary. Never near the distributor.
I was going to do that, but i would think the line would be close to the header?
|
|
|
Re: Holley 4150 fuel lines, Whats your setup?
[Re: 440challenger]
#537383
11/26/09 04:00 PM
11/26/09 04:00 PM
|
Joined: Nov 2007
Posts: 21,937
Kirkland, Washington
Pacnorthcuda
Too Many Posts
|
Too Many Posts
Joined: Nov 2007
Posts: 21,937
Kirkland, Washington
|
Quote:
Quote:
On mine I flipped the "t" to the carb around (so it faces the firewall) and ran hard line from the mechanical pump along the frame rail (basically reversing the path of the tank-to-pump line and then went up the firewall and connected.
Its very sanitary. Never near the distributor.
I was going to do that, but i would think the line would be close to the header?
Its not an issue on mine. 70 Cuda, Heddman headers.
|
|
|
Re: Holley 4150 fuel lines, Whats your setup?
[Re: 440challenger]
#537386
11/27/09 08:48 AM
11/27/09 08:48 AM
|
Joined: Jan 2003
Posts: 24,562
Brookeville, Md
Mr.Yuck
Not enough dumb comments...yet
|
Not enough dumb comments...yet
Joined: Jan 2003
Posts: 24,562
Brookeville, Md
|
Quote:
I have a 4150 holley on my 440 and was trying to use a cheapo chrome fuel line and when installed the inlet is almost smashed right up against my distributor. Does anyone know of a fuel line that will work in this case? I would run two braided liens but im trying to keep this kind of stock looking. Really was trying to stay away from AN fittings and braided line. Thanks!
flip the line backwards, make the inlet towards the back of the carb not the front. Like this, but do a better job w/ the line than I did. That was a rush job.
|
|
|
Re: Holley 4150 fuel lines, Whats your setup?
[Re: 69L78Nova]
#537389
11/27/09 09:17 PM
11/27/09 09:17 PM
|
Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
1_WILD_RT
Management Trainee
|
Management Trainee
Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
|
Quote:
I like that. Looks sharp!
Thanks! I try to keep it looking stock, but running a little bettter..
|
|
|
Re: Holley 4150 fuel lines, Whats your setup?
[Re: 383man]
#537391
11/27/09 11:15 PM
11/27/09 11:15 PM
|
Anonymous
Unregistered
|
Anonymous
Unregistered
|
I went with the Fabulous Fabrications fuel line on my old 440 and plan to again soon. His stuff is quality, cheap, and fits right the first time!
|
|
|
Re: Holley 4150 fuel lines, Whats your setup?
#537392
11/27/09 11:33 PM
11/27/09 11:33 PM
|
Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
1_WILD_RT
Management Trainee
|
Management Trainee
Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
|
Quote:
I went with the Fabulous Fabrications fuel line on my old 440 and plan to again soon. His stuff is quality, cheap, and fits right the first time!
My only issue with his stuff is it is patterned after a factory Chevrolet fuel line for any engine originally equipt with a dual feed Holley...
|
|
|
Re: Holley 4150 fuel lines, Whats your setup?
[Re: 1_WILD_RT]
#537393
11/28/09 07:39 AM
11/28/09 07:39 AM
|
Joined: Mar 2007
Posts: 9,336
South-Central (Sebring), FL
Commando1
master
|
master
Joined: Mar 2007
Posts: 9,336
South-Central (Sebring), FL
|
Quote:
Quote:
I went with the Fabulous Fabrications fuel line on my old 440 and plan to again soon. His stuff is quality, cheap, and fits right the first time!
My only issue with his stuff is it is patterned after a factory Chevrolet fuel line for any engine originally equipt with a dual feed Holley...
I could care less about losing a tenth of a point at Pebble Beach. It's a flawless fit and it makes tight radius turns with no crimping. He also has the right 45 degree bend from the carb inlet to avoid jamming it up against the manifold.
Best of all, he avoids that torturous route behind the dizzy and it STILL lines up to the stock gas filter.
|
|
|
Re: Holley 4150 fuel lines, Whats your setup?
[Re: 1_WILD_RT]
#537395
11/28/09 01:12 PM
11/28/09 01:12 PM
|
Joined: Nov 2004
Posts: 1,601
Hatfield,Pa.
bigD
top fuel
|
top fuel
Joined: Nov 2004
Posts: 1,601
Hatfield,Pa.
|
Quote:
I went with the stock look...  I still need to go back & do a cleaner job, but it's been working this way for 4,000 miles..
I did the same thing,went down to the auto parts house ,got all the fittings and tubing ,built my own,D.
2015 Chrysler200s,2008 Charger R/T R&T,1999 Dakota R/T,1999 Viper ACR,1968 Charger R/T.
|
|
|
Re: Holley 4150 fuel lines, Whats your setup?
#537396
11/28/09 04:52 PM
11/28/09 04:52 PM
|
Joined: Aug 2003
Posts: 2,682
Clinton Twp. Michigan
coronet1966d
master
|
master
Joined: Aug 2003
Posts: 2,682
Clinton Twp. Michigan
|
Quote:
I went with the Fabulous Fabrications fuel line on my old 440 and plan to again soon. His stuff is quality, cheap, and fits right the first time!
webstie? i searched it on google and got nothing
|
|
|
Re: Holley 4150 fuel lines, Whats your setup?
[Re: coronet1966d]
#537397
11/28/09 07:51 PM
11/28/09 07:51 PM
|
Anonymous
Unregistered
|
Anonymous
Unregistered
|
Quote:
webstie? i searched it on google and got nothing
I had to dig out my copy of MCG the other day to find his information.
His number is (303)666-9882
AHA, web address:
http://members.aol.com/sixpackbee/index.html
|
|
|
|
|
