FOR SALE Hemi engine crankshaft nut thick washer. Price $20.00 shipping included in the price Bob Horman

Manley 22441 Hemi valve springs. Double spring with dampner. 170# on the seat, 500# open. Included are 10 degree Titanium retainers and shims. Have about 200 miles of street driving on them. $80 or best offer. Shipping from 85268 is not included in this price. I DO NOT ACCEPT PAYPAL. Payment with bank or postal money order or old fashioned personal check.
Thaks for looking.
Chris

FOR SALE Champion spark plugs N14Y Brand new on sealed card. Price $45.00 shipping included in price Bob Horman

Looking for the six side bolts and washers for the Hemi main caps. I have the ARP ones, I want the stock look.
Thanks in advance.

Mopar Performance 426 HEMI aluminum crossram intake manifold, it was bolted on a engine at one time but never ran $1650.00 (708) 288-2879

1 set of 8 Stage V 426 HEMI intake roller rockers, 1.6 ratio, nice used condition $950.00 (708) 288-2879

Set of 16 original 426 Hemi Rocker Arms and 4 Stands $750 rich1981@optonline.net

1 Pr. aftermarket velocity stacks for 426 HEMI crossram or Max Wedge running 3705 carbs or Edelbrock aftermarket carbs $250.00 for the pair (708) 288-2879

For sale: Edelbrock Rat Roaster 3 intake manifold base. It's in Decent shape. The four barrel top plate is cracked and in need of
welding. All of the cracksE are "veed out" and ready for welding. Someone also "hogged out" the four butterfly holes in the top! If you just want the base it's $200 plus shipping. If you want the top also it's $250 for everything plus shipping from 11772. Thanks, Rick

***************** NOTE: REDUCED PRICE !!!!! **********************

Weighs 16lbs, Bottom 11Lbs mag, Top Alum 5lbs, as pictured
In good condition
$600 OBO, plus shipping, PM

Edit I was asked today to add a pic of the bottom shown below. It looks like a valley tray ( not included bolts to bottom of manifold.
It's not included because I don't have it, but looks simple to fabricate out of a single piece sheet metal and drilling eight 1/4" holes.

$5800...Email me at Dragula426@gmail.com or call 716-830-1258. No games please.

I have a Callies Hemi block just sitting here at the moment. It is not setup for internal pickup. It is the 4.5 Bore version, and it is used but in great shape. Needs nothing, but a little paint. Used one season. Again. nothing wrong with it.

Also have a set of diamond pistons that can go with it for a little extra.

And if you're really wanting to jump the shark, I am willing to sell my current running Hemi....

New never mounted Hemi crossram for sale. Ports have been gasket matched and ported for maximum even flow. Perfect condition with all mounting hardware included. Comes with set of Superformance intake gaskets. A lot of time has been spent on the runners. This is the last of my Hemi parts for sale.$1400 or best reasonable offer. Price reduced $1,100 FIRM Buyer pays shipping cost if needed. Thank you Gary 810-796-two four six one. Cell 810-728-two three seven zero.

Any gen 2 426 hemi solid flat tappet .680 approx lift cams for sale?

Many years back when I installed a Hemi crate in my 68 R/T, I devised a factory looking bracket and kit to allow use of the existing accel cable and Kickdown linkage.
I have 12 brackets and hardware for the kits. The kit will bolt right on to a single 4 intake and looks like the factory made it.
It can also be used with a manual trans or Automatic as the pivot point for KD linkage is separate but included.
More than enough hardware (Nuts, couplings etc.) is included for all 12 brackets.
I've looked for a better pic of the kit installed but haven't found it yet
The threaded rod, couplings and locknuts are used to lengthen the Top and mid KD rods if needed.
My intention was to sell them individually but life happens
Anticipated retail is 150- 200 per kit which would = $1800 - 2400.00

I am asking 1000.00 plus shipping for all 12 kits and the design.

EDIT: Talking with a prospective buyer on 1 kit it occurred to me that these brackets may fit other manifolds as the bracket uses the two rear manifold bolts for mounting

if there was enough interest I may consider selling the kits indidually

Will ship with pre payment, and references are available.

May separate at higher individual prices if there is enough interest
PM me here
Thanks 🍻

NOS Hemi Fuel Pump 2585118 Carter 4024 NOS fuel pump for 426 Hemi applications. I do not see any date code stamped. $500.00 including shipping in lower 48 states.

NOS Chrysler Mopar Thermostat 195* part number 3418459, $20

I can check shipping to your location.

Located in New Jersey

Email Kenei@comcast.net

For sale Hemi Block $5800 PM me here, or call me at 716-830-1258 or email me at Dragula426@gmail.com

Callies Hemi Iron block

Slightly used, nothing wrong with it. Could use a final hone for cross hatch, but all is good.

Currently painted orange

Had this in my Cuda as a 605 a couple years back, hurt a rod bearing and went and used another block

Block has a 4.500 bore, and is clearance for a 4.75 stroke.

I have a set of Diamond pistons that can go with it for extra. They are 4.503 or there abouts. They are also for a 4.75 stroke and a perfect fit with a hone touch up.