8 3/4 center section. This is 742 case with 3.73 gears and sure-grip posi unit. Has small yoke (7260 U-joint). Unit was hardly used and in excellent condition. Ready to bolt in. Asking $750. (Can't ship) Contact Bud: Kramden426 at aol.com

8 3/4 center section. This is a 489 case open with 2.76 gears and small yoke (7260 U-joint). Ready to bolt in and use as is or use as core to put new gears in. Asking $125. Contact Bud: Kramden426 at aol.com

Narrowed Dana 60 rear. Measures 52 5/8" end to end. Stock width for an A-body car. Includes open center carrier, pinion with yoke and new rear cover. Asking $500 for all. (Can't ship) Contact Bud: Kramden426 at aol.com

Pair of shock plates and long u-bolts for 8 3/4, Dana or 8 1/4. Missing a few of the locking nuts. Asking $60 for all. Contact Bud: Kramden426 at aol.com

Original 4.10 and 3.54 gear ratio tags. The 3.54 tag is a little rough but still usable. $10 for the 4.10 and $5 for the 3.54 + postage. No Paypal.

gt340 at yahoo.com

Rear brake hardware for 8 3/4 or Dana rear:
10" x 2 1/2" backing plates, 10" x 2 1/2" drums (NIB), new brake shoes and hardware kits.
Asking $125 for all.
Contact Bud: Kramden426 at aol.com

8 3/4 & Dana 60 Axle Bearing Retainer Adjuster Flanges. Used, $50 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Mopar Alum 8.75 Carrier NIB
Catalog stated when released new design is 10% stronger than original design
Likely last new one available in the country
As Is
$2200 plus shipping, delivery possible east of Mississippi with agreed upon reasonable extra fee

I have 4, decided to use my Mag Dana 60 instead of this one w/BB stroker 5 spd B body.

Supposedly new 5.57 8-3/4 gear set for 489 case, brand unknown but it is stamped USA with the 'heart' stamping. I got these and a set of 5.38s 2 years ago installed with spools, but decided they're probably a bit too low for my current project. I removed them tonight and will replace them with a 5.13 gear. I'll remove the pinion bearings tomorrow and clean then for better pictures, nonetheless, here they are, $325 shipped USPS to the lower 48 continental states. If you're interested or have any questions, please contact me here, thanks for viewing.

Selling a few 8.75 yokes, small u-joint yokes $30 ea, one is fine thread, one is coarse thread, large u-joint yoke is new-$60, have a 742 case, 4.56 gears, 35 spline Moser spool, less than 200 miles on gears, went to a Dana, can take pics $700,

New, 29 Spline 39/7 as pictured, covered in rust preservative, in SW Fla $250 OBO + Shipping PM

New 2.93 10 Spline R&P covered in rust preservative in SW Fla $150 OBO + Shipping

This is a typical used 8.75 489 housing cleaned up and plated, nothing special performance wise
$80 + shipping from SW Fla PM

8.75" 742 with 10 spline MW billet 1350 Yoke with 2 MW Billet caps, ARP ring bolts.
MW spool, will have to verify spool spline count and 4.30 ratio, it's been years.
All new bearings/parts brand new except housing, never run nor installed, professionally built
Over $1500 in parts new w/o labor
$1350 + shipping, delivery east of Mississippi possible at additional fee, from SW Fla PM

These caps are new never been installed. they require minor fitting by installer, as all aftermarket upgrade caps do.
The blue paint marking means they have been Cyro treated.
It's common thinking only the driver's side cap fails first, therefore it's the only one thought to need an upgrade. There is no known downsides to doing both caps other than cost.
Meaning two 8.75's can be upgraded here, I am not willing to separate.
$250 + Shipping SW Fla PM





#12-1-119-2049

8.75" 742 Richmond 4.10 R&P New 10 Spline
As Is, As pictured shipped in Original Box
$200+ Shipping SW Florida PM

8.75" 742 3.55 R&P New 10 Spline
Rust preventive is White Lithium spray grease
As Is, As pictured shipped in Original packing
$325+ Shipping SW Florida PM

8.75" 742 Billet CM Yoke 1350 10 Spline New
As is, As pictured
$190 + Shipping from SW Fla PM

8.75" Differential bearing adjusters New
As is, As pictured
$55 + Shipping from SW Fla PM

Rear axle Ring & Pinion set. This is a 4:10 ratio gear set used in the 8 3/4 rears, 489 case #. It has very limited usage and is like new. $200 Pickup only (Phoenix, AZ). Too expensive to ship. Contact Joe via text @ 623.734.6104.

Selling a 742 case pumpkin, large yoke, 35 spline Moser spool, 4.56 gears with less than hundred street miles, no hits, $700 plus shipping, located in Lancaster, California, contact me here via PM.