Dominator air bleeds - Moparts Forums

Register Log In Moparts Forums Unlawfl's Race & Engine Tech Dominator air bleeds

Print Thread

Page 2 of 2

1

2

Re: Dominator air bleeds [Re: 493_DART] #285264 04/14/09 08:37 PM 04/14/09 08:37 PM
Joined: Aug 2005 Posts: 777 Southington Ct. T turbobitt super stock
turbobitt super stock T Joined: Aug 2005 Posts: 777 Southington Ct.	Try removing just the 4 inner bleeds. I think those are the high speed bleeds. Removing those should sut down the high speed circuit and any possible influence it can have on the idle circuit. If it cleans up the idle, then at least you have some sort of direction. Allan G. 1970 Challenger w/572 Hemi street car and my pride and joy. 1986 T-Type with 272 Stage 2 Buick V6 engine - True 8 second street car. Just updated the engine and put down 928 HP @ 35# boost to the ground on chasis dyno. 1976 Cee Bee Avenger Jet Boat - 460 Ford powered.

Re: Dominator air bleeds [Re: turbobitt] #285265 04/14/09 08:40 PM 04/14/09 08:40 PM
Joined: Jul 2004 Posts: 4,384 Worst Weather USA 493_DART OP master
493_DART OP master Joined: Jul 2004 Posts: 4,384 Worst Weather USA	ok, will try that

Re: Dominator air bleeds [Re: 493_DART] #285266 04/14/09 09:04 PM 04/14/09 09:04 PM
Joined: Jun 2003 Posts: 9,225 Charleston S sixpackgut Drag Week Mod Champion
sixpackgut Drag Week Mod Champion S Joined: Jun 2003 Posts: 9,225 Charleston	8082 is a 2 circuit stock IAB is 71 and the high speed is 37 i think your tmming is to low. my procedure is this, with carb off the car, i set throttle blades. install carb then set timming to desired idle rpm. if it wants 22* then i adjust dist to get the disired advance or lock it out. mine is basically at total at idle Last edited by sixpackgut; 04/14/09 09:12 PM. Gen 3 power 6.22@110, 9.85@135 Follow @g3hemiswap on instagram performance only racing, CRT, ultimate converter, superior design concepts, ThumperCarbs

Re: Dominator air bleeds [Re: sixpackgut] #285267 04/14/09 09:13 PM 04/14/09 09:13 PM
Joined: Jul 2004 Posts: 4,384 Worst Weather USA 493_DART OP master
493_DART OP master Joined: Jul 2004 Posts: 4,384 Worst Weather USA	yes sir--thats whats in it-- i should be able to fine tone my dist when the kit arrives. maybe my idle mix isnt as bad as i think.....i usually run the car in the garage...YES, the door is open....... it wont idle unless i have both blades/idle screws at around 2-3 turns and the mix screws around 1.5 turns out..... Last edited by 496dart; 04/14/09 09:14 PM.

Re: Dominator air bleeds [Re: 493_DART] #285268 04/14/09 09:14 PM 04/14/09 09:14 PM
Joined: Jun 2003 Posts: 9,225 Charleston S sixpackgut Drag Week Mod Champion
sixpackgut Drag Week Mod Champion S Joined: Jun 2003 Posts: 9,225 Charleston	i fixed my post Gen 3 power 6.22@110, 9.85@135 Follow @g3hemiswap on instagram performance only racing, CRT, ultimate converter, superior design concepts, ThumperCarbs

Re: Dominator air bleeds [Re: 493_DART] #285269 04/14/09 09:18 PM 04/14/09 09:18 PM
Joined: Jun 2003 Posts: 9,225 Charleston S sixpackgut Drag Week Mod Champion
sixpackgut Drag Week Mod Champion S Joined: Jun 2003 Posts: 9,225 Charleston	Quote: yes sir--thats whats in it-- i should be able to fine tone my dist when the kit arrives. maybe my idle mix isnt as bad as i think.....i usually run the car in the garage...YES, the door is open....... it wont idle unless i have both blades/idle screws at around 2-3 turns and the mix screws around 1.5 turns out..... i think your exposing the transfer slot trying to raise your rpm when you shold use the dist. Gen 3 power 6.22@110, 9.85@135 Follow @g3hemiswap on instagram performance only racing, CRT, ultimate converter, superior design concepts, ThumperCarbs

Re: Dominator air bleeds [Re: 493_DART] #285270 04/14/09 09:28 PM 04/14/09 09:28 PM
Joined: Jun 2003 Posts: 9,225 Charleston S sixpackgut Drag Week Mod Champion
sixpackgut Drag Week Mod Champion S Joined: Jun 2003 Posts: 9,225 Charleston	Quote: too late to start the car tonight... But, i cant find any info on my carb its NOT listed on Holleys site! its a 80823 , 2 circuit idle . Im wanting to know the stock jet size / bleed sizes / pv sizes . Ive searched the web now for 30 minutes. my int. bleeds are 37 and the idle bleeds are 71 air bleeds are stock 84 jet square stock 6.5 PV front and rear stock( i ditch the rear PV and toss a 90 jet in there but you can see how it runs with it) nice simple carb Gen 3 power 6.22@110, 9.85@135 Follow @g3hemiswap on instagram performance only racing, CRT, ultimate converter, superior design concepts, ThumperCarbs

Re: Dominator air bleeds [Re: sixpackgut] #285271 04/14/09 09:33 PM 04/14/09 09:33 PM
Joined: Jul 2004 Posts: 4,384 Worst Weather USA 493_DART OP master
493_DART OP master Joined: Jul 2004 Posts: 4,384 Worst Weather USA	thanks sixgut-- will report back after i get some more initial in it

Re: Dominator air bleeds [Re: sixpackgut] #285272 04/14/09 10:42 PM 04/14/09 10:42 PM
Joined: Dec 2004 Posts: 182 USA N Nitrofish member
Nitrofish member N Joined: Dec 2004 Posts: 182 USA	I agree with sixpackgut. I had the same problem with my 8896-1 Dominator. For the engine to idle it was necessary to open the throttle plates to far and it left the transfer slots completely exposed. I ended up drilling small holes in each throttle plate to correct the concern and increasing ignition timing. It sounds like your idle mixture is set correctly at this time. Mixture screws 1 1/2 turns out from seated is the correct normal range, Fining tuning can be done later but thats pretty close for now.

Re: Dominator air bleeds [Re: Nitrofish] #285273 04/21/09 07:14 PM 04/21/09 07:14 PM
Joined: Jul 2004 Posts: 4,384 Worst Weather USA 493_DART OP master
493_DART OP master Joined: Jul 2004 Posts: 4,384 Worst Weather USA	Well, i re-curved the dist today with the Mallory kit. Now ive got 20 initial / 35 total. The curve starts around 1300 and is all in by 2500. I also welded the pickup plate--the pickup was moving up and down because of the vac adv. lever, enough to really alter the air gap. I was able to adjust the carb a little-not much . Its nice and responsive blipping the throttle at 1,000 rpm . Now if i could just get to the dam track!

Page 2 of 2

1

2

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1