Re: /6 To 360 Magnum Parts and Labor Checklist
[Re: sharpie]
#265526
03/26/09 01:14 PM
03/26/09 01:14 PM
|
Joined: Jan 2003
Posts: 16,123 Grand Haven, MI
patrick
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 16,123
Grand Haven, MI
|
those look to be the summit shorties that didn't work for IMGTX in his E body--IIRC in his car the collector hit the steering shaft. I'm debating if I want to try these edelbrock 66013 headers in my 5th ave they're slightly longer and might take care of the clearance issue IMGTX had, and they're coated stainless...the downside is they're $460, or $30 more than bare dougs headers (but $130 cheaper than the coated dougs D453's)
1976 Spinnaker White Plymouth Duster, /6 A833OD 1986 Silver/Twilight Blue Chrysler 5th Ave HotRod **SOLD!*** 2011 Toxic Orange Dodge Charger R/T 2017 Grand Cherokee Overland 2014 Jeep Cherokee Latitude (holy crap, my daughter is driving)
|
|
|
Re: /6 To 360 Magnum Parts and Labor Checklist
[Re: sharpie]
#265530
03/26/09 05:14 PM
03/26/09 05:14 PM
|
Joined: Jan 2008
Posts: 377 Michigan Troll
blk00rt
enthusiast
|
enthusiast
Joined: Jan 2008
Posts: 377
Michigan Troll
|
im in the process of the swap right now. I used just regular old a body headers in my dart. They seem to work well, but I have not fired it up yet. I do have to reroute the power steering hose. I have manual brakes so no booster to worry about.
Rob Dunn 1976 Dart Sport 360 2000 dakota RT 408 with 150 nitrous 2013 Dodge Ram 1500 Hemi 2009 Jeep Patriot
|
|
|
Re: /6 To 360 Magnum Parts and Labor Checklist
[Re: sharpie]
#265532
03/26/09 10:03 PM
03/26/09 10:03 PM
|
Joined: Jan 2003
Posts: 12,861 Gloucester,VA STOP MOVING HERE
RangerDan440
OP
I Live Here
|
OP
I Live Here
Joined: Jan 2003
Posts: 12,861
Gloucester,VA STOP MOVING HERE
|
well I took some very rudimentary measurements and looking at the car, I think I might be able to make the truck manifolds work (remember I have manual steering and brakes so Im at an advantage for space) Anyone ever have issues with motor mount shims? I may be able to pull this off with only having to buy the Schumacher mounts
68 Valiant 408 69 Charger 318 69 Cougar 351W 70 Torino GT 351C 71 Country Squire 351W 71 Road Runner 440+6 71 Satellite sedan 318 73 Duster 318 73 Challenger 383 77 Grand Prix 455 83 Malibu 9C1 383 84 Delta 88 403 87 Grand National 96 Ram 360 09 Crown Vic 10 Challenger R/T M6 15 Challenger Hellcat M6
|
|
|
Re: /6 To 360 Magnum Parts and Labor Checklist
[Re: Wedgeman]
#265534
03/27/09 06:20 AM
03/27/09 06:20 AM
|
Joined: Jun 2008
Posts: 10,847 Oakdale CT
gdonovan
I Live Here
|
I Live Here
Joined: Jun 2008
Posts: 10,847
Oakdale CT
|
Quote:
don't forget the nose extension for the camshaft
Daniel
I have the bolt & washer part of the HUG 7011 kit if anyone wants it for $19 shipped, decided to go electric.
|
|
|
Re: /6 To 360 Magnum Parts and Labor Checklist
[Re: RangerDan440]
#265536
03/27/09 06:33 AM
03/27/09 06:33 AM
|
Joined: Jun 2008
Posts: 10,847 Oakdale CT
gdonovan
I Live Here
|
I Live Here
Joined: Jun 2008
Posts: 10,847
Oakdale CT
|
Quote:
Anyone ever have issues with motor mount shims?
When I shoved a 360 in my GTX for a bit I had no problems.
I wonder where the hell that engine is now? The mind goes...
|
|
|
Re: /6 To 360 Magnum Parts and Labor Checklist
[Re: gdonovan]
#265537
03/27/09 08:54 AM
03/27/09 08:54 AM
|
Joined: Jan 2003
Posts: 16,123 Grand Haven, MI
patrick
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 16,123
Grand Haven, MI
|
Quote:
Quote:
Gary,
Don't know about the Jeep ones....what would fit is a 68-70 340 style driver's side manifold, the one going upward.....you know ?
Daniel
Yes that would be best but in researching the issue there is two problems.
1) People report a port mismatch at the bottom causing an exhaust leak (either right away or when the gasket burns through due to so little meat being there)
2) Cost of the early "header" manifold.
The older manifolds are nice looking but the cost to power ratio is not there for me and dyno reports back that up.
If I can fit the 92 magnum manfolds in they go toe to toe with the 68-70 340 in regards to flow and there are no sealing issues. If I have to go with the jeep manifolds (which arrived yesterday, I'll take pics today) then at best I'll lose a few hp and live with that.
I'm too old to be changing gaskets every year, I want to assemble the car and go and make it as idiot proof (trouble free) as possible.
Great dyno shoot out on manifolds here-
http://www.moparmusclemagazine.com/techa...aust/index.html
I intend to compile a lot of information on my website so in the future there is a guide for these conversions.
jeep manifolds have been discussed before and are a no-go. the jeeps move the starter to the pass side of the engine, so the drivers side jeep manifold dumps right on top of the starter in a normal LA configuration.
1976 Spinnaker White Plymouth Duster, /6 A833OD 1986 Silver/Twilight Blue Chrysler 5th Ave HotRod **SOLD!*** 2011 Toxic Orange Dodge Charger R/T 2017 Grand Cherokee Overland 2014 Jeep Cherokee Latitude (holy crap, my daughter is driving)
|
|
|
Re: /6 To 360 Magnum Parts and Labor Checklist
[Re: patrick]
#265538
03/27/09 09:31 AM
03/27/09 09:31 AM
|
Joined: Jun 2008
Posts: 10,847 Oakdale CT
gdonovan
I Live Here
|
I Live Here
Joined: Jun 2008
Posts: 10,847
Oakdale CT
|
Quote:
jeep manifolds have been discussed before and are a no-go. the jeeps move the starter to the pass side of the engine, so the drivers side jeep manifold dumps right on top of the starter in a normal LA configuration.
With both style starters?
|
|
|
|
|