Duster rebuild Indy 655ci - Moparts Forums

Register Log In Moparts Forums Unlawfl's Race & Engine Tech Duster rebuild Indy 655ci

Print Thread

Page 2 of 3

1

2

3

Re: Duster rebuild Indy 655ci [Re: Bigcube] #1633771 06/15/14 09:31 AM 06/15/14 09:31 AM
Joined: Aug 2006 Posts: 1,403 Columbus Ohio M Moore & Moore OP pro stock
Moore & Moore OP pro stock M Joined: Aug 2006 Posts: 1,403 Columbus Ohio	The heads are Indy 600-13X We bought another set this spring and will be doing some flow comparing this week between the 2 sets.

Re: Duster rebuild Indy 655ci [Re: Moore & Moore] #1633772 06/15/14 12:38 PM 06/15/14 12:38 PM
Joined: Apr 2005 Posts: 2,128 Salt Lake City C camastomcat top fuel
camastomcat top fuel C Joined: Apr 2005 Posts: 2,128 Salt Lake City	Quote: I ran this motor some last year. It was in Jeff Hurst and Chuck Andersons dragster's and ran 6.80-7.20's depending weather they ran motor or sprayed. I had some issues with the Pro Systems carbs and we pulled it out after the Norwalk race. We are putting new rods, pistons, lifters, valves and valve springs in. I also bought a Neal Chance convertor to try and see how it preforms against my ATI and Coan. The block is a 4.84 bore spacing. I should have it running next month. I'm very interested in what these heads are capable of. Was the Hurst engine 655?

Re: Duster rebuild Indy 655ci [Re: camastomcat] #1633773 06/15/14 03:26 PM 06/15/14 03:26 PM
Joined: Feb 2005 Posts: 20,204 PA. pittsburghracer "Little"John
pittsburghracer "Little"John Joined: Feb 2005 Posts: 20,204 PA.	Gene Nagy's Stratus is running 4.60's at PRP (no adder) with those heads. 1970 Duster Edelbrock headed 408 5.984@112.52 422 Indy headed small block 5.982@112.56 mph 9.42@138.27 Livin and lovin life one day at a time

Re: Duster rebuild Indy 655ci [Re: Moore & Moore] #1633774 06/15/14 11:03 PM 06/15/14 11:03 PM
Joined: Apr 2005 Posts: 1,506 TN S SCATPACK 1 pro stock
SCATPACK 1 pro stock S Joined: Apr 2005 Posts: 1,506 TN	Quote: Block #2 Jack What oils the distributor oil pump drive on these blocks? It is closed off from the liftergaley, so no splash oiling for it. Thanks jerry Old Geezer Racing

Re: Duster rebuild Indy 655ci [Re: SCATPACK 1] #1633775 06/16/14 12:03 AM 06/16/14 12:03 AM
Joined: Dec 2008 Posts: 742 Oak Harbor, WA W Wicked49670dart super stock
Wicked49670dart super stock W Joined: Dec 2008 Posts: 742 Oak Harbor, WA	very nice! 70 Dart 3400 496 New Best 6.15@110.37 660ft, 9.76@135 with a 1.34 60ft

Re: Duster rebuild Indy 655ci [Re: Moore & Moore] #1633776 06/16/14 12:28 PM 06/16/14 12:28 PM
Joined: Feb 2004 Posts: 3,441 Mo. S supercomp master
supercomp master S Joined: Feb 2004 Posts: 3,441 Mo.	Quote: I ran this motor some last year. It was in Jeff Hurst and Chuck Andersons dragster's and ran 6.80-7.20's depending weather they ran motor or sprayed. I had some issues with the Pro Systems carbs and we pulled it out after the Norwalk race. We are putting new rods, pistons, lifters, valves and valve springs in. I also bought a Neal Chance convertor to try and see how it preforms against my ATI and Coan. The block is a 4.84 bore spacing. I should have it running next month. Was those the single blade carbs?

Re: Duster rebuild Indy 655ci [Re: supercomp] #1633777 06/16/14 04:59 PM 06/16/14 04:59 PM
Joined: Feb 2003 Posts: 3,998 GO BUCKS !!!!!!! 3 340RICK master
340RICK master 3 Joined: Feb 2003 Posts: 3,998 GO BUCKS !!!!!!!	Man Jack that crank of yours is purty I am sure you here that all the time...right If that were me it would have rolled off the tailgate while I was taking the photo

Re: Duster rebuild Indy 655ci [Re: 340RICK] #1633778 06/16/14 05:14 PM 06/16/14 05:14 PM
Joined: Feb 2005 Posts: 20,204 PA. pittsburghracer "Little"John
pittsburghracer "Little"John Joined: Feb 2005 Posts: 20,204 PA.	Quote: Man Jack that crank of yours is purty I am sure you here that all the time...right If that were me it would have rolled off the tailgate while I was taking the photo That tailgate of Jacks is famous. Its in most of his for sale ads. 1970 Duster Edelbrock headed 408 5.984@112.52 422 Indy headed small block 5.982@112.56 mph 9.42@138.27 Livin and lovin life one day at a time

Re: Duster rebuild Indy 655ci [Re: pittsburghracer] #1633779 06/16/14 08:53 PM 06/16/14 08:53 PM
Joined: Aug 2006 Posts: 1,403 Columbus Ohio M Moore & Moore OP pro stock
Moore & Moore OP pro stock M Joined: Aug 2006 Posts: 1,403 Columbus Ohio	Here are some answers to some of the questions asked earlier. 1 The block is a 4.84 bore spacing 2 The Hurst engine was a 655ci 3 The oil pump drive shaft gets oil thrown on it from the cam and crankshaft 4 The carbs are Pro-System Nitrous Pro-IV(not single blade) 5 The tailgate is the best table I have Lol Last edited by Moore & Moore; 06/16/14 08:59 PM.

Re: Duster rebuild Indy 655ci [Re: Moore & Moore] #1633780 06/17/14 01:47 AM 06/17/14 01:47 AM
Joined: Oct 2011 Posts: 515 geezer acres rest home D dakotawilly mopar
dakotawilly mopar D Joined: Oct 2011 Posts: 515 geezer acres rest home	looks like youve been to the jewelry store jack! did you ever sell that koleno block? SFI 25.5 depends,no leak,even at 213 mph....

Re: Duster rebuild Indy 655ci [Re: dakotawilly] #1633781 06/17/14 10:26 PM 06/17/14 10:26 PM
Joined: Aug 2006 Posts: 1,403 Columbus Ohio M Moore & Moore OP pro stock
Moore & Moore OP pro stock M Joined: Aug 2006 Posts: 1,403 Columbus Ohio	Here is a photo of the open area below the oil pump drive. 8179399-P1010004.JPG (245 downloads)

Re: Duster rebuild Indy 655ci [Re: Moore & Moore] #1633782 06/17/14 10:30 PM 06/17/14 10:30 PM
Joined: Aug 2006 Posts: 1,403 Columbus Ohio M Moore & Moore OP pro stock
Moore & Moore OP pro stock M Joined: Aug 2006 Posts: 1,403 Columbus Ohio	The block was honed at Wasserbeck Speed Shop on a Sunnen SV-10 Diamond hone. Here is a photo of the machine setup with RPM, Speed and X-hatch angle. I will post hone finish surface specs tomorrow. 8179403-P1010011.JPG (243 downloads) Last edited by Moore & Moore; 06/17/14 10:33 PM.

Re: Duster rebuild Indy 655ci [Re: 340RICK] #1633783 06/17/14 11:16 PM 06/17/14 11:16 PM
Joined: Aug 2003 Posts: 7,065 Indiana maxie master
maxie master Joined: Aug 2003 Posts: 7,065 Indiana	I am impressed that it uses 4 crankshafts Were you going to run in the nostalgia pro stock?

Re: Duster rebuild Indy 655ci [Re: maxie] #1633784 06/18/14 12:41 AM 06/18/14 12:41 AM
Joined: Nov 2004 Posts: 3,619 Norwich CT USA Defbob master
Defbob master Joined: Nov 2004 Posts: 3,619 Norwich CT USA	Quote: I am impressed that it uses 4 crankshafts Were you going to run in the nostalgia pro stock?

Re: Duster rebuild Indy 655ci [Re: pittsburghracer] #1633785 06/18/14 03:19 PM 06/18/14 03:19 PM
Joined: Aug 2005 Posts: 1,175 where its cold and white durin... 2QUICK4U super stock
2QUICK4U super stock Joined: Aug 2005 Posts: 1,175 where its cold and white durin...	Quote: Gene Nagy's Stratus is running 4.60's at PRP (no adder) with those heads. im hoping to see these number with my daytona and my 655 with dual sv1s...made 1 pass last weekend and went 5.35@131 with some more tuning and possibly a convetor adjustment. .4.80s should be in reach....

Re: Duster rebuild Indy 655ci [Re: 2QUICK4U] #1633786 06/18/14 11:05 PM 06/18/14 11:05 PM
Joined: Aug 2006 Posts: 1,403 Columbus Ohio M Moore & Moore OP pro stock
Moore & Moore OP pro stock M Joined: Aug 2006 Posts: 1,403 Columbus Ohio	Made some progress tonight after work. Got the rods and pistons in. I put the cam in and hope to get it degreed in tomorrow night. It is a Cam Motion 55mm with 4/7 swap. The specs with 1.8 rockers are .900/.850 lift and 283/303 duration R117. 8180556-P1010017.JPG (207 downloads)

Re: Duster rebuild Indy 655ci [Re: Moore & Moore] #1633787 01/12/15 08:30 PM 01/12/15 08:30 PM
Joined: Jan 2003 Posts: 2,937 A shed in England Tig master
Tig master Joined: Jan 2003 Posts: 2,937 A shed in England	Any more news? '74 Challenger..9.46 @ 145.9 1/4, 6.001 @ 118 1/8 so far. 4023lb !!! # N/A, Marsh performance 655ci, Indy Maxx, T/R, Indy 600-13 X's, Street legal, pump gas, full interior, Cal-Tracs, mufflers, 3:73's and real 10.5 radials. 9.51 @ 142.4 1/4, 6.003 @ 114 1/8 with our old mule KB, 572-13, 580 wedge. RHD '68 Barracuda Fastback 323ci street/strip. Best ET 13.88 @ 99.03

Re: Duster rebuild Indy 655ci [Re: Tig] #1633788 01/12/15 10:44 PM 01/12/15 10:44 PM
Joined: Feb 2004 Posts: 855 ontario canada kingston aspenrt360 super stock
aspenrt360 super stock Joined: Feb 2004 Posts: 855 ontario canada kingston	that crank coating looks very interesting! 2013 Chrysler 300 touring 1974 Dodge Charger SE. 360-727-8.75-3.23 sure grip 1972 Dodge Dart Swinger 1995 Dodge Ram 1500 4x4

Re: Duster rebuild Indy 655ci [Re: Moore & Moore] #1633789 01/13/15 02:03 AM 01/13/15 02:03 AM
Joined: Jun 2010 Posts: 3,112 LONG ISLAND fishy340 master
fishy340 master Joined: Jun 2010 Posts: 3,112 LONG ISLAND	Nice stuff

Re: Duster rebuild Indy 655ci [Re: Moore & Moore] #1633790 01/13/15 02:14 AM 01/13/15 02:14 AM
Joined: Nov 2008 Posts: 180 Ohio, United States BuckeyeBrawler member
BuckeyeBrawler member Joined: Nov 2008 Posts: 180 Ohio, United States	Jack parts look great glad to hear you're getting it put together. The tailgate is good as well. Brawler

Page 2 of 3

1

2

3

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1