Post deleted by Defbob
[Re: cudadan]
#126869
09/27/08 02:58 PM
09/27/08 02:58 PM
|
Anonymous
Unregistered
|
Anonymous
Unregistered
|
|
|
|
Re: vibration update on the cuda
#126871
09/27/08 03:10 PM
09/27/08 03:10 PM
|
Joined: Aug 2003
Posts: 2,617 Stratford nj
cudadan
OP
master
|
OP
master
Joined: Aug 2003
Posts: 2,617
Stratford nj
|
Quote:
junk the car
LOL i have been known to do that LOl yeah woody there is enough end play i made sure of that,
|
|
|
Re: vibration update on the cuda
[Re: smokinwoody]
#126873
09/27/08 03:19 PM
09/27/08 03:19 PM
|
Joined: Aug 2003
Posts: 2,617 Stratford nj
cudadan
OP
master
|
OP
master
Joined: Aug 2003
Posts: 2,617
Stratford nj
|
Quote:
my Camaro has a vibration now after I bottomed out on a bump in the road...after that it now has a vibration at certain rpm's..I must have hit the driveshaft ...problem is its one of those MATRIX shafts ...
have you checked the harmonic balancer...or had anything looked at in the engine...
Im thinking you already did all that..
i ahd the stock balancer on it then went to an SFI one and still there, i would think if it was the motor that it would do it all the time, and if it was the motor also i'd think the front u joint would go before the rear.
|
|
|
Re: vibration update on the cuda
[Re: smokinwoody]
#126875
09/27/08 03:32 PM
09/27/08 03:32 PM
|
Joined: Aug 2003
Posts: 2,617 Stratford nj
cudadan
OP
master
|
OP
master
Joined: Aug 2003
Posts: 2,617
Stratford nj
|
Quote:
not only do I ask dumb questions but I dont read..
rear U joint...pinion yoke?
LMAO, i tried 2 different yoke, a small one and now i run a 7290 series on it. still the same, this all started when i had the trans redone last winter.thats why i thought it was the trans. but i changed everything in the trans but the housing, i looked over it and no cracks andywhere either
|
|
|
Re: vibration update on the cuda
[Re: cudadan]
#126876
09/27/08 03:45 PM
09/27/08 03:45 PM
|
Anonymous
Unregistered
|
Anonymous
Unregistered
|
Guess you do have the correct converter and balancer for a 360 being externally balanced?
|
|
|
Re: vibration update on the cuda
#126877
09/27/08 03:48 PM
09/27/08 03:48 PM
|
Joined: Aug 2003
Posts: 2,617 Stratford nj
cudadan
OP
master
|
OP
master
Joined: Aug 2003
Posts: 2,617
Stratford nj
|
Quote:
Guess you do have the correct converter and balancer for a 360 being externally balanced?
yeah the car has been together for awhile , then this started,
|
|
|
Re: vibration update on the cuda
[Re: bobby66]
#126879
09/27/08 04:03 PM
09/27/08 04:03 PM
|
Joined: Aug 2003
Posts: 2,617 Stratford nj
cudadan
OP
master
|
OP
master
Joined: Aug 2003
Posts: 2,617
Stratford nj
|
Quote:
Wheel and axle bearings good?
changed them all
|
|
|
Re: vibration update on the cuda
[Re: cudadan]
#126881
09/27/08 04:20 PM
09/27/08 04:20 PM
|
Joined: Jan 2003
Posts: 9,116 Falconer, NY
KatFysh
master
|
master
Joined: Jan 2003
Posts: 9,116
Falconer, NY
|
I cracked a second tailshaft housing 3 weeks ago. I'm finally ready to go tear it apart tomorrow. What I'm gonna do is drop 3 lines. One from the balancer, 1 from the trans tailshaft and one from the rear pinion yoke. Then gonna check it with a laser level to see where the line runs from front to back. I'm thinking on mine that I may be off side to side with my trans crossmember. Also, did you use a new crush sleeve when you swapped yokes? I didn't on mine and that is another thought I had. Maybe the pinion isn't set correctly creating the vibrations. But I'm not getting any groaning noises. What I guess I'm asking here is, do you think that with all the times that you've had yours apart, that maybe the tailshaft isn't located exactly where it was before all this started, up/down & side to side ? When was the very time you took it apart for this problem? What was wrong then?
When you decide to quit, THAT is the moment when you would've succeeded..
|
|
|
Re: vibration update on the cuda
[Re: hot67cuda]
#126883
09/27/08 04:34 PM
09/27/08 04:34 PM
|
Joined: Aug 2003
Posts: 2,617 Stratford nj
cudadan
OP
master
|
OP
master
Joined: Aug 2003
Posts: 2,617
Stratford nj
|
Quote:
run it on the stands with the tires off. put all the lug nuts on it .have someone turn one of the axles with a dail indicator on the flange watch the run out do the same for the driveshaft u find it.If they check out good it could br a ring gear out of balence.
did that too and all was good. this is the worst problem i ever had
|
|
|
|
|