4 speed install, cutting input shaft

Print Thread

Re: 4 speed install, cutting input shaft [Re: RMCHRGR] #2685479 08/07/19 07:51 PM 08/07/19 07:51 PM
Joined: Dec 2009 Posts: 1,023 pa. D dan9 super stock
dan9 super stock D Joined: Dec 2009 Posts: 1,023 pa.	To remove a bushing you can pack it full of grease and get a proper sized wooden dowel rod, tap on it and they come right out. I’m not sure if it works with a bearing but it should.

Entire Thread
Subject	Posted By	Posted
4 speed install, cutting input shaft	RMCHRGR	08/06/19 06:38 PM
Re: 4 speed install, cutting input shaft	Cab_Burge	08/06/19 07:41 PM
Re: 4 speed install, cutting input shaft	RapidRobert	08/06/19 08:06 PM
Re: 4 speed install, cutting input shaft	RapidRobert	08/06/19 09:22 PM
Re: 4 speed install, cutting input shaft	1DGEMAN	08/06/19 09:37 PM
Re: 4 speed install, cutting input shaft	RMCHRGR	08/07/19 12:51 AM
Re: 4 speed install, cutting input shaft	poorboy	08/07/19 01:21 AM
Re: 4 speed install, cutting input shaft	1DGEMAN	08/07/19 09:38 AM
Re: 4 speed install, cutting input shaft	1DGEMAN	08/07/19 09:35 AM
Re: 4 speed install, cutting input shaft	RapidRobert	08/07/19 04:09 PM
Re: 4 speed install, cutting input shaft	peabodyracing	08/06/19 08:13 PM
Re: 4 speed install, cutting input shaft	RMCHRGR	08/06/19 09:23 PM
Re: 4 speed install, cutting input shaft	Cab_Burge	08/06/19 09:34 PM
Re: 4 speed install, cutting input shaft	jbc426	08/07/19 02:30 PM
Re: 4 speed install, cutting input shaft	dan9	08/07/19 08:31 PM
Re: 4 speed install, cutting input shaft	John_Kunkel	08/07/19 05:13 PM
Re: 4 speed install, cutting input shaft	500ciDuster	08/07/19 05:22 PM
Re: 4 speed install, cutting input shaft	RMCHRGR	08/07/19 06:58 PM
Re: 4 speed install, cutting input shaft	stumpy	08/07/19 07:04 PM
Re: 4 speed install, cutting input shaft	John_Kunkel	08/07/19 07:54 PM
Re: 4 speed install, cutting input shaft	RMCHRGR	08/07/19 10:58 PM
Re: 4 speed install, cutting input shaft	dan9	08/07/19 11:51 PM
Re: 4 speed install, cutting input shaft	slantzilla	08/08/19 01:13 AM
Re: 4 speed install, cutting input shaft	fourgearsavoy	08/08/19 02:43 AM
Re: 4 speed install, cutting input shaft	stumpy	08/08/19 03:00 AM
Re: 4 speed install, cutting input shaft	RMCHRGR	08/09/19 01:46 AM
Re: 4 speed install, cutting input shaft	Cab_Burge	08/09/19 03:27 AM
Re: 4 speed install, cutting input shaft	dan9	08/11/19 09:46 PM
Re: 4 speed install, cutting input shaft	MoonshineMattK	08/07/19 08:21 PM
Re: 4 speed install, cutting input shaft	stumpy	08/07/19 08:26 PM

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To