Anyone know the weights for Scat BB H-beaM rods?
#560611
12/23/09 11:50 AM
12/23/09 11:50 AM
|
Joined: Jan 2003
Posts: 15,439
Val-haul-ass... eventually
BradH
OP
Taking time off to work on my car
|
OP
Taking time off to work on my car
Joined: Jan 2003
Posts: 15,439
Val-haul-ass... eventually
|
Anyone know the weights (total, big end, small end) for Scat BB H-beam 6.76" (.990" or 1.094" pin) rods? They seem to be one of the few rods I can't find specs for and am trying to figure out where they compare to other rods for possible future use.
Also, I've heard a couple of cases recently about Scat's machining work not being as good as in the past. Has this applied to their rods, cranks, "everything"?
Last edited by Captain Cheapo!; 12/23/09 08:59 PM.
|
|
|
Re: Anyone know the weights for Scat BB H-bean rods?
[Re: BradH]
#560612
12/23/09 01:36 PM
12/23/09 01:36 PM
|
Joined: Feb 2007
Posts: 5,080
organ
maximum entropy
master
|
master
Joined: Feb 2007
Posts: 5,080
organ
|
h bean rods- good for gas engines (FACETIOUS COMMENT, JOKING).
for what is the good life if not doing things thoughtfully?
|
|
|
Re: Anyone know the weights for Scat BB H-bean rods?
[Re: BradH]
#560614
12/24/09 01:47 AM
12/24/09 01:47 AM
|
Joined: Nov 2007
Posts: 277
MN
Willie68coronet
enthusiast
|
enthusiast
Joined: Nov 2007
Posts: 277
MN
|
I bought a set of these rods with the .990 pin and from memory they were about 855 grams when I totaled them up. I looked on the box today but the numbers got oiled and dissapeared. I brought them into wheeler racing engines and they measured/inspected them and said they were good to go out of the box. Machining looks good. Nice rods
Edit: I found the weights for my rods on the box when I shined a bright light on it they are: Big end-576g, small end-278g. 854 I was close.
Last edited by willie_68coronet; 12/29/09 12:09 AM.
'68 Coronet 500 w/ Indy EZ-1 headed 446, 727 trans, 9" rear
First day at the track with SUV street tires and no traction: 1.688 60', 7.24 @ 101.79 in the 1/8 mile
Great customer service from: DominicThumper Carbs, B3 racing engines, Porter Racing Engines, A-1 torque converter's, Quick Performance, Racer Brown Cams, R&R Performance, Manton pushrods
|
|
|
Re: Anyone know the weights for Scat BB H-beaM rods?
[Re: BradH]
#560615
12/24/09 11:31 AM
12/24/09 11:31 AM
|
Joined: Jan 2003
Posts: 16,928
NC
440Jim
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 16,928
NC
|
Quote:
Anyone know the weights (total, big end, small end) for Scat BB H-beam 6.76" (.990" or 1.094" pin) rods?
Since nobody seems to have a list, let's start our own for all the SCAT H-beam rods. I have these in my engine:
6.535, 0.990, 2.200 bearing: 566.6 + 237.6 = 804.2 grams
|
|
|
Re: Anyone know the weights for Scat BB H-beaM rods?
[Re: 440Jim]
#560616
12/24/09 12:20 PM
12/24/09 12:20 PM
|
Joined: Feb 2007
Posts: 6,295
U.S.
moparniac
master
|
master
Joined: Feb 2007
Posts: 6,295
U.S.
|
eddie miller sells scat stuff....... have to see him on yellowbullet though.
Mopar Performance
|
|
|
Re: Anyone know the weights for Scat BB H-beaM rods?
[Re: moparniac]
#560618
12/24/09 01:34 PM
12/24/09 01:34 PM
|
Joined: Jan 2003
Posts: 15,439
Val-haul-ass... eventually
BradH
OP
Taking time off to work on my car
|
OP
Taking time off to work on my car
Joined: Jan 2003
Posts: 15,439
Val-haul-ass... eventually
|
Quote:
eddie miller sells scat stuff...
So does Dan Costello (DRAM); it's a "no brainer" who I'd deal with.
|
|
|
Re: Anyone know the weights for Scat BB H-bean rods?
[Re: ZIPPY]
#560621
12/24/09 05:45 PM
12/24/09 05:45 PM
|
Joined: Jan 2003
Posts: 15,439
Val-haul-ass... eventually
BradH
OP
Taking time off to work on my car
|
OP
Taking time off to work on my car
Joined: Jan 2003
Posts: 15,439
Val-haul-ass... eventually
|
Quote:
... the Manley products in my 451 are (ballpark) 900 with the same oal/big end/little end/crank pin dimensions.
The Eagle .990" rods in my RB 452 are 880-890g, IIRC. Definitely room to go on a diet, although I'm comfortable they'll take all the abuse I'll ever throw at 'em.
|
|
|
|
|
