correct size screw for hood callout - Moparts Forums

Register Log In Moparts Forums Moparts Restoration & A12 Forum correct size screw for hood callout

Print Thread

Page 1 of 2

1

2

correct size screw for hood callout #555738 12/16/09 09:00 PM 12/16/09 09:00 PM
Joined: Jan 2003 Posts: 541 C car48nut OP mopar
car48nut OP mopar C Joined: Jan 2003 Posts: 541	anybody know the correct size of the screw that holds the engine callout strips on the 68 roadrunner? thanks

Re: correct size screw for hood callout [Re: car48nut] #555739 12/16/09 09:04 PM 12/16/09 09:04 PM
Joined: Jan 2003 Posts: 8,160 DELAWARE TONY_DAGOSTINO master
TONY_DAGOSTINO master Joined: Jan 2003 Posts: 8,160 DELAWARE	hi, i dont know the size, but the screws were also used on 69 dart taillight bezels tony www.TONYSPARTS.COM

Re: correct size screw for hood callout [Re: car48nut] #555740 12/16/09 09:29 PM 12/16/09 09:29 PM
Joined: Jun 2003 Posts: 21,428 It's a dry heat gtx6970 Too Many Posts
gtx6970 Too Many Posts Joined: Jun 2003 Posts: 21,428 It's a dry heat	Don't hold me to it, but I think they're an 8-32 Again, I'm not sure so take for what it is, a guess

Re: correct size screw for hood callout [Re: TONY_DAGOSTINO] #555741 12/16/09 11:01 PM 12/16/09 11:01 PM
Joined: Jan 2003 Posts: 541 C car48nut OP mopar
car48nut OP mopar C Joined: Jan 2003 Posts: 541	Thanks , I will look for them

Re: correct size screw for hood callout [Re: gtx6970] #555742 12/17/09 01:02 AM 12/17/09 01:02 AM
Joined: Jan 2003 Posts: 21,507 N.E. OHIO, USA A12 Too Many Posts
A12 Too Many Posts Joined: Jan 2003 Posts: 21,507 N.E. OHIO, USA	Quote: Don't hold me to it, but I think they're an 8-32 Again, I'm not sure so take for what it is, a guess Bill, said it before "you're good".......I was afraid I was going to lose these screws when I was restoring my '68 rr so here's what I documented..... 5672787-DSC00781.JPG (74 downloads)

Re: correct size screw for hood callout [Re: A12] #555743 12/17/09 01:03 AM 12/17/09 01:03 AM
Joined: Jan 2003 Posts: 21,507 N.E. OHIO, USA A12 Too Many Posts
A12 Too Many Posts Joined: Jan 2003 Posts: 21,507 N.E. OHIO, USA	2 5672788-DSC00787.JPG (83 downloads)

Re: correct size screw for hood callout [Re: A12] #555744 12/17/09 01:10 AM 12/17/09 01:10 AM
Joined: Jan 2003 Posts: 21,507 N.E. OHIO, USA A12 Too Many Posts
A12 Too Many Posts Joined: Jan 2003 Posts: 21,507 N.E. OHIO, USA	32 TPI MikeR 5672795-68RRhoodcalloutscrewdimension.jpg (54 downloads)

Re: correct size screw for hood callout [Re: A12] #555745 12/17/09 01:18 AM 12/17/09 01:18 AM
Joined: Jan 2003 Posts: 21,507 N.E. OHIO, USA A12 Too Many Posts
A12 Too Many Posts Joined: Jan 2003 Posts: 21,507 N.E. OHIO, USA	'68 Hood Callout 5672809-i-8_B_L.jpg (62 downloads)

Re: correct size screw for hood callout [Re: A12] #555746 12/17/09 08:42 AM 12/17/09 08:42 AM
Joined: Jan 2003 Posts: 541 C car48nut OP mopar
car48nut OP mopar C Joined: Jan 2003 Posts: 541	does anybody have them? Maybe year one or someone else like that.

Re: correct size screw for hood callout [Re: car48nut] #555747 12/17/09 10:02 AM 12/17/09 10:02 AM
Joined: Jun 2003 Posts: 21,428 It's a dry heat gtx6970 Too Many Posts
gtx6970 Too Many Posts Joined: Jun 2003 Posts: 21,428 It's a dry heat	Quote: does anybody have them? Maybe year one or someone else like that. Not that I'm aware of. Everyone I got my hands on the head is to big. They'll work just will not appear correct

Re: correct size screw for hood callout [Re: car48nut] #555748 12/17/09 10:12 AM 12/17/09 10:12 AM
Joined: Nov 2004 Posts: 1,923 Medina, Ohio HEMICUDA top fuel
HEMICUDA top fuel Joined: Nov 2004 Posts: 1,923 Medina, Ohio	Call Tom at R/T (570) 388-1082, I pretty sure he has those.

Re: correct size screw for hood callout [Re: HEMICUDA] #555749 12/17/09 03:04 PM 12/17/09 03:04 PM
Joined: Dec 2005 Posts: 335 Olympia WA R rocketresto enthusiast
rocketresto enthusiast R Joined: Dec 2005 Posts: 335 Olympia WA	They are called 100� head. I found the OE manufacturer, buy they don't make them the same way anymore, they are all hex head now and have D.O.T. numbers for the aircraft industry. Hopefully Tom at RT has found another place to get them. Mike

Re: correct size screw for hood callout [Re: rocketresto] #555750 12/17/09 07:50 PM 12/17/09 07:50 PM
Joined: Nov 2003 Posts: 1,029 Southeast Virginia 68jim super stock
68jim super stock Joined: Nov 2003 Posts: 1,029 Southeast Virginia	I searched high and low for some of those screws when I was doing my 68 Road Runner. Mine were mostly good but I had a few bad ones. I put a wanted add out and a gent from Canada sent me 6 or so of those screws that he had left over from another project for free!. After I put together a good set of 8 and still had a few decent ones left over. Someone else posted about a year ago needed some and I sent what I had to him for free as well. Kind of like a pay-it-forward deal. I'm all out now but can someone else help out the original poster in the spirit of Merry Christmas??? Jim

Re: correct size screw for hood callout [Re: TONY_DAGOSTINO] #555751 12/17/09 08:36 PM 12/17/09 08:36 PM
Joined: Nov 2006 Posts: 3,407 S.E. Florida, USA rrunner master
rrunner master Joined: Nov 2006 Posts: 3,407 S.E. Florida, USA	Quote: hi, i dont know the size, but the screws were also used on 69 dart taillight bezels tony Also found on 69 Fury fender emblems. They are a bit longer and need to be shortened, but the thread and head are correct.

Re: correct size screw for hood callout [Re: rrunner] #555752 12/17/09 09:40 PM 12/17/09 09:40 PM
Joined: May 2005 Posts: 2,295 dark side of the moon D Dougsmopars top fuel
Dougsmopars top fuel D Joined: May 2005 Posts: 2,295 dark side of the moon	There an odd ball screw. Number 8 with number 4 head. R/T Specialites has a few. I bought some for my 68. Call them he had some left.

Re: correct size screw for hood callout [Re: Dougsmopars] #555753 12/17/09 10:03 PM 12/17/09 10:03 PM
Joined: Jun 2003 Posts: 21,428 It's a dry heat gtx6970 Too Many Posts
gtx6970 Too Many Posts Joined: Jun 2003 Posts: 21,428 It's a dry heat	same screw used on Challenger rallye hood scoop insert. And 66 Chrysler 300 side of the fender diecast trim

Re: correct size screw for hood callout [Re: gtx6970] #555754 12/20/09 12:40 AM 12/20/09 12:40 AM
Joined: Jun 2003 Posts: 4,872 connecticut pnypwr master
pnypwr master Joined: Jun 2003 Posts: 4,872 connecticut	I need a set too...i got inserts and call outs but no screws "Are you gonna bark all day lil doggy? Or are you gonna bite?" 05 ram 2500 ctd 74 gremlin x 360 65 mustang 347 70 coronet R/T 440 03 Mach 1

Re: correct size screw for hood callout [Re: pnypwr] #555755 09/10/10 05:14 PM 09/10/10 05:14 PM
Joined: Sep 2010 Posts: 5 Chatsworth Ca D Dave Gunther member
Dave Gunther member D Joined: Sep 2010 Posts: 5 Chatsworth Ca	I know this is an old thread but I made a set of these for a friend and can make some more. If anyone has a need i can send you picture of my reproduction next to an original. Dave

Re: correct size screw for hood callout [Re: Dave Gunther] #555756 09/10/10 06:34 PM 09/10/10 06:34 PM
Joined: Jan 2003 Posts: 21,507 N.E. OHIO, USA A12 Too Many Posts
A12 Too Many Posts Joined: Jan 2003 Posts: 21,507 N.E. OHIO, USA	Quote: I know this is an old thread but I made a set of these for a friend and can make some more. If anyone has a need i can send you picture of my reproduction next to an original. Dave How about a set at a discount for supplying the photos and documentation........ naw just kidding so how about at least posting a photo of your repo's

Re: correct size screw for hood callout [Re: Dave Gunther] #555757 09/10/10 08:14 PM 09/10/10 08:14 PM
Joined: Jun 2003 Posts: 21,428 It's a dry heat gtx6970 Too Many Posts
gtx6970 Too Many Posts Joined: Jun 2003 Posts: 21,428 It's a dry heat	Quote: I know this is an old thread but I made a set of these for a friend and can make some more. If anyone has a need i can send you picture of my reproduction next to an original. Dave lets see it, please Last edited by gtx6970; 09/10/10 08:16 PM.

Re: correct size screw for hood callout [Re: gtx6970] #555758 09/10/10 09:10 PM 09/10/10 09:10 PM
Joined: Sep 2010 Posts: 5 Chatsworth Ca D Dave Gunther member
Dave Gunther member D Joined: Sep 2010 Posts: 5 Chatsworth Ca	The screws on the left are mine and the right original 6189211-IMG00027-20100909-1829.jpg (81 downloads)

Re: correct size screw for hood callout [Re: Dave Gunther] #555759 09/10/10 09:11 PM 09/10/10 09:11 PM
Joined: Sep 2010 Posts: 5 Chatsworth Ca D Dave Gunther member
Dave Gunther member D Joined: Sep 2010 Posts: 5 Chatsworth Ca	The head is a #2. I was unable to find a #1 blank. Material is stainless. 6189214-tn.jpg (47 downloads) Last edited by Dave Gunther; 09/10/10 09:17 PM.

Re: correct size screw for hood callout [Re: Dave Gunther] #555760 09/10/10 09:14 PM 09/10/10 09:14 PM
Joined: Sep 2010 Posts: 5 Chatsworth Ca D Dave Gunther member
Dave Gunther member D Joined: Sep 2010 Posts: 5 Chatsworth Ca	and.... 6189224-IMG00025-20100909-1827.jpg (56 downloads)

Re: correct size screw for hood callout [Re: Dave Gunther] #555761 09/10/10 09:19 PM 09/10/10 09:19 PM
Joined: Sep 2010 Posts: 5 Chatsworth Ca D Dave Gunther member
Dave Gunther member D Joined: Sep 2010 Posts: 5 Chatsworth Ca	and 1 more. 6189241-IMG00026-20100909-1828.jpg (53 downloads)

Page 1 of 2

1

2

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1