Re: ENGINE FINALLY DONE AND DYNO'D
[Re: 512 VALIANT]
#452801
08/28/09 09:46 PM
08/28/09 09:46 PM
|
Joined: Dec 2007
Posts: 10,542 BROOK PARK, OH
WILD BILL
Senior Member of the Junior Dragster Club
|
Senior Member of the Junior Dragster Club
Joined: Dec 2007
Posts: 10,542
BROOK PARK, OH
|
Cool
What kind of ET's you looking for with it?
|
|
|
Re: ENGINE FINALLY DONE AND DYNO'D
[Re: 512 VALIANT]
#452802
08/28/09 09:51 PM
08/28/09 09:51 PM
|
Joined: Mar 2007
Posts: 1,608 Rudolph, Ohio
moparguy7074
top fuel
|
top fuel
Joined: Mar 2007
Posts: 1,608
Rudolph, Ohio
|
Quote:
400 block 4.40 bore 4.15 stroke 13:5 comp ported Victor heads and intake .690 solid roller 1.6 rockers 1050 dom. 702.4 hp @ 6300 662.6 tq @ 4800 pics to come later
HP seems kind of low, what rpm was it run up to?
|
|
|
Re: ENGINE FINALLY DONE AND DYNO'D
[Re: moparguy7074]
#452804
08/29/09 12:20 AM
08/29/09 12:20 AM
|
Joined: Oct 2008
Posts: 1,015 Down South
DaKuda
super stock
|
super stock
Joined: Oct 2008
Posts: 1,015
Down South
|
Quote:
Quote:
400 block 4.40 bore 4.15 stroke 13:5 comp ported Victor heads and intake .690 solid roller 1.6 rockers 1050 dom. 702.4 hp @ 6300 662.6 tq @ 4800 pics to come later
HP seems kind of low, what rpm was it run up to?
Sounds strong to me....Cant wait to see pictures.
|
|
|
Re: ENGINE FINALLY DONE AND DYNO'D
[Re: WILD BILL]
#452805
08/29/09 12:37 PM
08/29/09 12:37 PM
|
Joined: Dec 2008
Posts: 136 CHANDLER, AZ
512 VALIANT
OP
member
|
OP
member
Joined: Dec 2008
Posts: 136
CHANDLER, AZ
|
Quote:
Cool
What kind of ET's you looking for with it?
I was originally going to run 10.90, but w/ the #'s it put out I'll have to slow it way down. the car wieghs less than 2800 w/ me and a the big block in it. After I get comfortable w/ the car I may try super gas ??? - The car is back halfed and has 32x14x15's and a 727 w/ brake and 4500 stall. Thx for the comments I read a lot of your posts.
|
|
|
Re: ENGINE FINALLY DONE AND DYNO'D
[Re: 512 VALIANT]
#452806
08/29/09 12:42 PM
08/29/09 12:42 PM
|
Joined: Jan 2003
Posts: 4,152 SO. CAL.
70blackfish
master
|
master
Joined: Jan 2003
Posts: 4,152
SO. CAL.
|
man that car is lite are your heads max wedge size ports? what did they flow? .......cool car!
Last edited by 70blackfish; 08/29/09 12:43 PM.
|
|
|
Re: ENGINE FINALLY DONE AND DYNO'D
[Re: moparguy7074]
#452808
08/29/09 12:57 PM
08/29/09 12:57 PM
|
Joined: Dec 2008
Posts: 136 CHANDLER, AZ
512 VALIANT
OP
member
|
OP
member
Joined: Dec 2008
Posts: 136
CHANDLER, AZ
|
Quote:
Quote:
400 block 4.40 bore 4.15 stroke 13:5 comp ported Victor heads and intake .690 solid roller 1.6 rockers 1050 dom. 702.4 hp @ 6300 662.6 tq @ 4800 pics to come later
HP seems kind of low, what rpm was it run up to?
6300 rpm @ 37 degrees timing #88 jets and it was 97 degrees ambient we were going to do a forth pull w/89's in it, but were not sure if we could duplicate correct air flow to justify it. Fuel per horsepower usage was dead on @ .397-.440 per # (you dyno guys will what I mean). ---- As far as low #'s!!!!!!! THIS IS NOT AN EXOTIC RACE ENGINE AT ALL. It is off the shelf parts - shaft rockers edlebrock heads etc. most (several engine builders) I spoke w/ assumed 650-675 including the shop the did the build. EVERYONE was very happy w/ the hp and the tq - they have done several builds similar and this was the highest producer yet by almost 35hp and 40tq. Shop owner said the heads came out REALLY NICE and that was the difference (335 @ .700). If I had B-1's or Indys I could see your point, but you could call Jegs or Herbert and probably have everthing in this engine shipped to your house w/ in a week.
|
|
|
Re: ENGINE FINALLY DONE AND DYNO'D
[Re: Al_Alguire]
#452809
08/29/09 01:32 PM
08/29/09 01:32 PM
|
Joined: Dec 2008
Posts: 136 CHANDLER, AZ
512 VALIANT
OP
member
|
OP
member
Joined: Dec 2008
Posts: 136
CHANDLER, AZ
|
Quote:
Great numbers should run well..NOW where are the dang pictures of the car
Here they are
|
|
|
Re: ENGINE FINALLY DONE AND DYNO'D
[Re: 70VcodeCoronetRT]
#452815
08/29/09 03:01 PM
08/29/09 03:01 PM
|
Joined: Dec 2008
Posts: 136 CHANDLER, AZ
512 VALIANT
OP
member
|
OP
member
Joined: Dec 2008
Posts: 136
CHANDLER, AZ
|
Quote:
Very nice!!!!!!! So those are the standard port victors then? Thanks and later
yes standard port -- and to jwilli500 I will find out rod length - i'm drawing a blank right now sorry
|
|
|
|
|