JW Ultrabell,flexplate and crank adapter to adapt a glide to big block mopar.
$550 + shipping.Venmo or paypal ok.707-478-6302

1 Pr. 15X4 Ansen aluminum slots, 4 1/2 inch bolt circle for Mopar or Ford, nice used condition, could use some polishing $800.00 for the pair (708) 288-2879

Used pair of Mickey Thompson 28x4.5x15 ET front drag tires. Were bought new in 2014 and used until 2017 when I went to a smaller tire. Have been stored in my garage under the steps since they were removed. Tires right around 200 passes on them. Asking $50 for the pair. Buyer must pick up in Keymar, MD or pay shipping cost.

Weldon 1100-A Pump &A2040 Regulator

Links:
https://www.weldonracing.com/store/1100-A-p56062401
https://www.weldonracing.com/store/A2040-Series-Bypass-Regulators-p56722017
Brought new 7/1/2022, used for 1 chassis dyno session, went in another direction. Fogged with Marvel Mystery Oil and put on shelf. Time to sell.
600.00$ Shipped lower 48 only.

PM me

MSD number 14 bushing from FBO $12 mailed US ( the dark bushing is out of my old MSD that I will include if you want it)

Vintage Moroso cool can, nice used condition $125.00 (708) 288-2879

New set of K1 4340 H-beam Big block Mopar connecting rods

7.000 length 2.200 rod journal .990 pin ARP2000 bolts (stock mopar width).

These rods allow offset grinding your stock 440 crank rod journals to increase stroke from 3.750 to 3.925 inches

The rods with increase stroke yield the following performance benefits.

1) Increase displacement of 20 cubic inches
2) Reduction in rotating weight (weight off crank journals/bearings plus light weight rod big end)
3) Improved rod/stroke ratio
4) Reduction in reciprocating weight (small end of rod plus lower compression height piston plus light .990 pin)
5) reduce rod bearing speeds

$585 plus shipping (I've had these several years and would likely be more than double this price today)

thanks

rapid340@yahoo.com

NOS Weiand 440 Tunnel Ram, Some light surface oxidation in spots, Never installed. $450 + Shipping , PM me here if interested

B1 cylinder heads with rocker shafts and stands. I received these in a package deal, don't really know any history on them, or what valve springs are on them $3,000 OBO. You can PM me with any questions.

18 gauge steel, -10AN female fittings x3. 12x12x12 $129 + shipping. PayPal FF or postal money order. PM me here please.

-10AN fittings on red ends. $49 + shipping, PayPal FF or postal money order. PM me here please.

2'-2 1/8' Step, Very Solid, Shiny Finish, Some Bluing, Evac Tubes and Breathers.
Also fit RB Engine with RMS or other Coil Over.
Were in my Demon with Rb and Stage 6 Heads

$900 Pick Up in Maryland DC Suburbs

$1200 new with $200 shipping

will add Photos

Chrysler aluminum, electronic, tach drive distributor #4120942 for RB motor in excellent condition, just removed from my race motor. $325 shipped.

CR12B early B-body fuel tank, has sump box welded in, sump box is about 1" below tank with 4" to 5" tall inside tank. Tank was coated inside and out by a company called Tank Renu. Guaranteed for life, here is a link.
https://www.gastankrenu.com/guarantee/#:~:text=Gas%20Tank%20Renu%20%E2%80%93%20USA%20coats,years%20on%20all%20other%20tanks.
Also has Aeromotive fuel filter with -10 outlet, -8 return,-6 vent. Also, can use a stock pickup, I have a new one to go with it. to plug the hole where it goes.
400$ Prefer local pick up, will ship at buyer's expense.
Located in Kansas City area.
Pm if interested.