452 casting
#3223190
03/27/24 04:49 PM
03/27/24 04:49 PM
|
Joined: Jan 2003
Posts: 1,607 westerly, ri. usa
440lebaron
OP
top fuel
|
OP
top fuel
Joined: Jan 2003
Posts: 1,607
westerly, ri. usa
|
hello, picked up a pair of "452" b/b heads for my stocker, has a 1/8" pipe plug on one end. is this factory? motor home?? never seen this before. also appear to be surfaced quite a bit, casting numbers on deck surface top 1/16th have been machined. deck thickness on lower head bolts is 1.00 thick, what's unsurfaced thickness?
all parts are sold as is, all parts are considered used no warranties or returns paypal/check/money order, shipping is from zip 02891, buyer pays paypal fees 24% IRS 1099A plus 3% of part price, check/money order preferred site is not monitored 24/7 there might be a delay in response
|
|
|
Re: 452 casting
[Re: 440lebaron]
#3223199
03/27/24 05:25 PM
03/27/24 05:25 PM
|
Joined: Oct 2005
Posts: 271 Anchorage, Alaska
metallicareload
enthusiast
|
enthusiast
Joined: Oct 2005
Posts: 271
Anchorage, Alaska
|
hello, picked up a pair of "452" b/b heads for my stocker, has a 1/8" pipe plug on one end. is this factory? motor home?? never seen this before. also appear to be surfaced quite a bit, casting numbers on deck surface top 1/16th have been machined. deck thickness on lower head bolts is 1.00 thick, what's unsurfaced thickness? What kind of spark plugs do those heads use? I’ve heard that uncut heads measure a little over 1”, but I’ve never measured personally ![shruggy shruggy](/ubbthreads/images/graemlins/custom/shruggy.gif)
440, 4-Speed, 3.54 1968, when Dinosaurs ruled the Earth
|
|
|
Re: 452 casting
[Re: 440lebaron]
#3223252
03/27/24 11:04 PM
03/27/24 11:04 PM
|
Joined: Jan 2003
Posts: 75,060 U.S.S.A.
JohnRR
I Win
|
I Win
Joined: Jan 2003
Posts: 75,060
U.S.S.A.
|
906's usually measure 1.00ish from the factory ,I never measured the set I had gotten from Paul Rossi back in the 80's , they were NOS castings , small plug with the water ports around the spark plugs.
What's the depth of the open part of the chamber , the set I had were over .100 , as deep as .130 in the center of the head.
running up my post count some more .
|
|
|
Re: 452 casting
[Re: 440lebaron]
#3223284
03/28/24 09:16 AM
03/28/24 09:16 AM
|
Joined: Jan 2003
Posts: 13,375 Marion, South Carolina [><]
an8sec70cuda
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 13,375
Marion, South Carolina [><]
|
The 1/8" pipe plug is factory and I believe to be only on motorhome heads. I just sold a set like that a few weeks ago. I removed them from a 440 that came out of a motorhome.
CHIP '70 hemicuda, 575" Hemi, 727, Dana 60 '69 road runner, 440-6, 18 spline 4 speed, Dana 60 '71 Demon, 340, low gear 904, 8.75 '73 Chrysler New Yorker, 440, 727, 8.75 '90 Chevy 454SS Silverado, 476" BBC, TH400, 14 bolt '06 GMC 2500HD LBZ Duramax
|
|
|
Re: 452 casting
[Re: an8sec70cuda]
#3223297
03/28/24 10:43 AM
03/28/24 10:43 AM
|
Joined: Jan 2003
Posts: 1,607 westerly, ri. usa
440lebaron
OP
top fuel
|
OP
top fuel
Joined: Jan 2003
Posts: 1,607
westerly, ri. usa
|
regular spark plug no taper, no steam holes, chamber depth measures .063 was there a calculation for surface milling for cc reduction?
Last edited by 440lebaron; 03/28/24 10:47 AM.
all parts are sold as is, all parts are considered used no warranties or returns paypal/check/money order, shipping is from zip 02891, buyer pays paypal fees 24% IRS 1099A plus 3% of part price, check/money order preferred site is not monitored 24/7 there might be a delay in response
|
|
|
Re: 452 casting
[Re: 440lebaron]
#3223302
03/28/24 11:01 AM
03/28/24 11:01 AM
|
Joined: Jan 2003
Posts: 14,506 So. Burlington, Vt.
fast68plymouth
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 14,506
So. Burlington, Vt.
|
The outer head bolt row is usually a reliable indicator for head milling.
Uncut heads will be right about 1.00” thick.
68 Satellite, 383 with stock 906’s, 3550lbs, 11.18@123 Dealer for Comp Cams/Indy Heads
|
|
|
Re: 452 casting
[Re: 440lebaron]
#3223349
03/28/24 01:24 PM
03/28/24 01:24 PM
|
Joined: Jan 2003
Posts: 75,060 U.S.S.A.
JohnRR
I Win
|
I Win
Joined: Jan 2003
Posts: 75,060
U.S.S.A.
|
regular spark plug no taper, no steam holes, chamber depth measures .063 was there a calculation for surface milling for cc reduction? .063 says to me it's been cut , I've never seen an open chamber head that shallow... is the open part of the chamber floor parallel to the deck surface ? That almost looks angle milled , which I've never heard being done to a big block wedge head?
running up my post count some more .
|
|
|
Re: 452 casting
[Re: JohnRR]
#3223355
03/28/24 01:38 PM
03/28/24 01:38 PM
|
Joined: Jan 2003
Posts: 1,607 westerly, ri. usa
440lebaron
OP
top fuel
|
OP
top fuel
Joined: Jan 2003
Posts: 1,607
westerly, ri. usa
|
casting area by number is at a angle chamber is flat
all parts are sold as is, all parts are considered used no warranties or returns paypal/check/money order, shipping is from zip 02891, buyer pays paypal fees 24% IRS 1099A plus 3% of part price, check/money order preferred site is not monitored 24/7 there might be a delay in response
|
|
|
Re: 452 casting
[Re: 440lebaron]
#3223497
03/29/24 08:57 AM
03/29/24 08:57 AM
|
Joined: Jan 2003
Posts: 75,060 U.S.S.A.
JohnRR
I Win
|
I Win
Joined: Jan 2003
Posts: 75,060
U.S.S.A.
|
casting area by number is at a angle chamber is flat The one set of NOS castings I had , the Paul Rossi heads , were the peanut plug /extra cooling holes version and the chambers were .110 to . 130 deep. CC the head , if it's less than 90-92 cc it's been cut.
Last edited by JohnRR; 03/29/24 08:58 AM.
running up my post count some more .
|
|
|
Re: 452 casting
[Re: an8sec70cuda]
#3223530
03/29/24 12:04 PM
03/29/24 12:04 PM
|
Joined: Oct 2005
Posts: 271 Anchorage, Alaska
metallicareload
enthusiast
|
enthusiast
Joined: Oct 2005
Posts: 271
Anchorage, Alaska
|
The 1/8" pipe plug is factory and I believe to be only on motorhome heads. I just sold a set like that a few weeks ago. I removed them from a 440 that came out of a motorhome. Starting to sound like these are some type of motorhome heads. The 452 heads I used on my 440 doesn’t have that boss drilled and tapped. It also took flat/gasket spark plugs
Last edited by metallicareload; 03/29/24 12:07 PM.
440, 4-Speed, 3.54 1968, when Dinosaurs ruled the Earth
|
|
|
|
|