Moparts Main Index | READ - Info & Help Page | Moparts Sponsors | Tech Archive

Forums Calendar Active Threads Search Forum Help
Previous Thread
Next Thread
Print Thread
Page 3 of 3 1 2 3
Re: anyone familiar with these rods [Re: Monte_Smith] #2024533
03/04/16 04:09 PM 03/04/16 04:09 PM
Joined: Jan 2007
Posts: 8,043
Mt Morris Michigan
mopar dave Offline OP
master
mopar dave  Offline OP
master

Joined: Jan 2007
Posts: 8,043
Mt Morris Michigan
i did buy them off ebay, but they do have ARP8740 stamped in them.

http://www.youtube.com/watch?v=aIxaesJ190U

http://youtu.be/lCZAaN7fFLg
Re: anyone familiar with these rods [Re: mopar dave] #2024543
03/04/16 04:20 PM 03/04/16 04:20 PM
Joined: Oct 2003
Posts: 11,686
W. Kentucky
justinp61 Offline
I Live Here
justinp61  Offline
I Live Here

Joined: Oct 2003
Posts: 11,686
W. Kentucky
By chance did you measure the shank at the head and the hole in the cap?
Re: anyone familiar with these rods [Re: mopar dave] #2024554
03/04/16 04:44 PM 03/04/16 04:44 PM
Joined: Sep 2014
Posts: 4,457
Washington
M
madscientist Offline
master
madscientist  Offline
master
M

Joined: Sep 2014
Posts: 4,457
Washington
I have turned many steel rods blue and used them again. As long as they clean up with out cutting the crap out of them to get them round.

Just because you think it won't make it true. Horsepower is KING. To dispute this is stupid. C. Alston
Re: anyone familiar with these rods [Re: justinp61] #2024589
03/04/16 06:11 PM 03/04/16 06:11 PM
Joined: Jan 2007
Posts: 8,043
Mt Morris Michigan
mopar dave Offline OP
master
mopar dave  Offline OP
master

Joined: Jan 2007
Posts: 8,043
Mt Morris Michigan
No what am I looking for?

http://www.youtube.com/watch?v=aIxaesJ190U

http://youtu.be/lCZAaN7fFLg
Re: anyone familiar with these rods [Re: mopar dave] #2024623
03/04/16 07:29 PM 03/04/16 07:29 PM
Joined: Oct 2003
Posts: 11,686
W. Kentucky
justinp61 Offline
I Live Here
justinp61  Offline
I Live Here

Joined: Oct 2003
Posts: 11,686
W. Kentucky
I was just curious to see how close the two were in diameter. I have a set of eagle and CompStars in the shop I'll measure.
Re: anyone familiar with these rods [Re: justinp61] #2024637
03/04/16 07:58 PM 03/04/16 07:58 PM
Joined: Jan 2007
Posts: 8,043
Mt Morris Michigan
mopar dave Offline OP
master
mopar dave  Offline OP
master

Joined: Jan 2007
Posts: 8,043
Mt Morris Michigan
I still have the old bolts but not with me at the moment.

http://www.youtube.com/watch?v=aIxaesJ190U

http://youtu.be/lCZAaN7fFLg
Re: anyone familiar with these rods [Re: mopar dave] #2025218
03/05/16 08:36 PM 03/05/16 08:36 PM
Joined: Oct 2003
Posts: 11,686
W. Kentucky
justinp61 Offline
I Live Here
justinp61  Offline
I Live Here

Joined: Oct 2003
Posts: 11,686
W. Kentucky
I measured my rods and bolts. On both sets the shank was .010" smaller than the bore in the cap.
Re: anyone familiar with these rods [Re: justinp61] #2025234
03/05/16 08:51 PM 03/05/16 08:51 PM
Joined: Jan 2007
Posts: 8,043
Mt Morris Michigan
mopar dave Offline OP
master
mopar dave  Offline OP
master

Joined: Jan 2007
Posts: 8,043
Mt Morris Michigan
I will check that out tomorrow.

http://www.youtube.com/watch?v=aIxaesJ190U

http://youtu.be/lCZAaN7fFLg
Page 3 of 3 1 2 3

Moderated by  Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer 
Privacy Policy · Forum Rules · Mark All Read Contact Us · Moparts




Moparts Main Index | READ - Info & Help Page | Moparts Sponsors | Tech Archive


Powered by UBB.threads™ PHP Forum Software 7.7.1