Re: Torsion bar removal tool..where to order for overnight?
[Re: jcc]
#1682912
10/07/14 12:26 AM
10/07/14 12:26 AM
|
Joined: Jun 2004
Posts: 9,404
Texas
carcrazyguy
OP
master
|
OP
master
Joined: Jun 2004
Posts: 9,404
Texas
|
Quote:
PM sent
And returned...  Thanks for the offer! We are trying to get a car together for a show this weekend. I did not plan on tearing it apart but spotted a few things that really needed to be done before we try to drive it very far. 
|
|
|
Re: Torsion bar removal tool..where to order for overnight?
[Re: 72440CUDA]
#1682914
10/07/14 12:36 AM
10/07/14 12:36 AM
|
Joined: Jul 2003
Posts: 898
Georgia
72440CUDA
super stock
|
super stock
Joined: Jul 2003
Posts: 898
Georgia
|
|
|
|
Re: Torsion bar removal tool..where to order for overnight?
[Re: carcrazyguy]
#1682917
10/07/14 12:49 AM
10/07/14 12:49 AM
|
Joined: Aug 2013
Posts: 106
Central IL
Trojmn
member
|
member
Joined: Aug 2013
Posts: 106
Central IL
|
sure i'd like to have a TB removal tool too, but since i don't and never think about it till i need it the very next day, i sure wouldn't overnight it. i just cant believe its *that* useful.
two bolts on the LBJ to knuckle, one on the strut to the LCA, LCA pin, swaybar links if you have one, and beat on the LCA to drive the TB back With urethane LCA bushings, dont even bother with the LCA pin. a scrap 2x or in my case a piece of oak floor, works well to drive the LCA.
or i have absolutely no idea what im missing... depends how often you're only under the car to swap a TBs i guess.
Last edited by Trojmn; 10/07/14 12:56 AM.
|
|
|
Re: Torsion bar removal tool..where to order for overnight?
[Re: carcrazyguy]
#1682920
10/07/14 11:32 AM
10/07/14 11:32 AM
|
Joined: Jan 2010
Posts: 667
Los Osos, Ca
CKessel
mopar
|
mopar
Joined: Jan 2010
Posts: 667
Los Osos, Ca
|
You don't need no steenking tool! Try this. Back the adjuster all the way off, pry the adjuster lever up, knock it down, repeat a few times. Notice how much travel you get out of the adjuster lever? Go about half of the travel. Back the lower control arm pin nut off like 1/8 to 1/4". Whack the nut end with a mallet. The bar should just slide out. I came up with this in a wrecking yard pulling off some control arms and it has worked well since.
Carl Kessel
|
|
|
Re: Torsion bar removal tool..where to order for overnight?
[Re: CKessel]
#1682921
10/07/14 02:02 PM
10/07/14 02:02 PM
|
Joined: Jan 2003
Posts: 27,467
So Cal
autoxcuda
Too Many Posts
|
Too Many Posts
Joined: Jan 2003
Posts: 27,467
So Cal
|
Quote:
You don't need no steenking tool! Try this. Back the adjuster all the way off, pry the adjuster lever up, knock it down, repeat a few times. Notice how much travel you get out of the adjuster lever? Go about half of the travel. Back the lower control arm pin nut off like 1/8 to 1/4". Whack the nut end with a mallet. The bar should just slide out. I came up with this in a wrecking yard pulling off some control arms and it has worked well since.
And since this car was just put together recently the T-bar might just slide back by hand when you back the adjuster off and take the clip out.
|
|
|
Re: Torsion bar removal tool..where to order for overnight?
[Re: bill440rt]
#1682924
12/04/14 01:03 AM
12/04/14 01:03 AM
|
Joined: Jan 2003
Posts: 5,789
Hamilton, Ontario Canada
Magnum
master
|
master
Joined: Jan 2003
Posts: 5,789
Hamilton, Ontario Canada
|
One the lower control arm is disconnected. Prybar between the lower control arm and k member will for the arm back, along with the torsion bar.
For bars seized in place. Use soft metal, like a 3/4" stock of aluminum bar. Hit the bar forwards to get it moving.
69 Super Bee, 93 Mustang LX, 04 Allure Super
|
|
|
|
|
Any ideas?
