Posted By: W5DART66
6.4 hemi CNC program. - 01/23/21 01:49 AM
Some pictures of my 6.4 program
In the 380s with stock intake valve.
In the 380s with stock intake valve.
6.4 hemi CNC program.
Posted By: W5DART66
Re: 6.4 hemi CNC program. - 01/23/21 01:51 AM
2
Posted By: Twostick
Re: 6.4 hemi CNC program. - 01/23/21 03:21 AM
Just as a point of reference for us mere mortals, what would a stock casting flow?
Kevin
Kevin
Posted By: fbs63
Re: 6.4 hemi CNC program. - 01/23/21 01:03 PM
What size does the chamber end up?
Posted By: HotRodDave
Re: 6.4 hemi CNC program. - 01/25/21 06:36 PM
6.4 BGE head or SRT? I hear the port shape is the same with just different material, Would it work in either casting? how does the flow compare in the lower lift regions like .500 .600 range, I assume 380 is pretty high up there.
Posted By: SRT6776
Re: 6.4 hemi CNC program. - 01/25/21 11:55 PM
Originally Posted by Twostick
Just as a point of reference for us mere mortals, what would a stock casting flow?
Kevin
Kevin
340+ IIRC
Posted By: W5DART66
Re: 6.4 hemi CNC program. - 01/26/21 12:55 AM
I will try to find the flow sheet.
Posted By: metallicareload
Re: 6.4 hemi CNC program. - 01/26/21 04:55 AM
Originally Posted by W5DART66
Some pictures of my 6.4 program
In the 380s with stock intake valve.
In the 380s with stock intake valve.
Can this only be done with 6.4L heads?
Posted By: Adrielp
Re: 6.4 hemi CNC program. - 01/27/21 11:50 AM
Awesome W5, I have a few questions. What is the average air speed speed and average CSA for your program? 90 or 91percent throat? Stock seat angles? Can you send me your email so I can contact you directly? Thanks
Posted By: GomangoCuda
Re: 6.4 hemi CNC program. - 01/28/21 06:03 PM
Originally Posted by Adrielp
Awesome W5, I have a few questions. What is the average air speed speed and average CSA for your program? 90 or 91percent throat? Stock seat angles? Can you send me your email so I can contact you directly? Thanks
His email address is in his profile.
Posted By: Adrielp
Re: 6.4 hemi CNC program. - 01/28/21 06:47 PM
Thanks!
Posted By: 52savoy
Re: 6.4 hemi CNC program. - 02/05/21 06:01 AM
Originally Posted by metallicareload
Originally Posted by W5DART66
Some pictures of my 6.4 program
In the 380s with stock intake valve.
In the 380s with stock intake valve.
Can this only be done with 6.4L heads?
All the Gen IIIs as far as I know. Not sure if it was on moparts or where-ever, someone did a great job welding up the heads. I think I saved at least one picture. Not sure if these are the heads.
Posted By: 52savoy
Re: 6.4 hemi CNC program. - 02/05/21 06:04 AM
These are the new MP I bought a few years ago and hope to have them assembled very soon. 2.10 int/1.60exh
Posted By: Taylor
Re: 6.4 hemi CNC program. - 02/08/21 10:38 PM
Like the Exhaust bowl, 380 with stock valve very impressive.