Know where I can buy a carbide burr like this one?

Posted By: BradH

Know where I can buy a carbide burr like this one? - 07/06/11 10:50 PM

I saw it in an older Steve Dulcich article and it looks like it would be handy for the port matching exercise I need to do on my welded-up intake runners.

Posted By: Deepockets

Re: Know where I can buy a carbide burr like this one? - 07/06/11 10:53 PM

McMaster Carr sells everything

Posted By: BradH

Re: Know where I can buy a carbide burr like this one? - 07/06/11 11:34 PM

Quote:

McMaster Carr sells everything

Not that one... (I just looked at their online catalog).

I suspect this was somebody's (Roger Helgesen) custom burr and not typical of what most suppliers offer. I'm sure I have something already that'll work, but thought the one pictured above would be better suited to a specific job I have to complete.

Posted By: CompWedgeEngines

Re: Know where I can buy a carbide burr like this one? - 07/06/11 11:52 PM

Check your Pms.

Posted By: MR_P_BODY

Re: Know where I can buy a carbide burr like this one? - 07/06/11 11:56 PM

Quote:

Check your Pms.

If you know where to get it please post it and not
just in a PM... thanks

Posted By: BeEtLeJuIcE !

Re: Know where I can buy a carbide burr like this one? - 07/06/11 11:57 PM

SD is on here from time to time ....send him a PM.

Posted By: abodiesonly1

Re: Know where I can buy a carbide burr like this one? - 07/06/11 11:59 PM

Did you try Grainger? They sell single cut, flame end burrs, just not sure if they're that long.

Edit...Try this web page

Posted By: 340Bird

Re: Know where I can buy a carbide burr like this one? - 07/07/11 12:09 AM

MSC will have it. The listing for burrs has like 1900 differant ones.
web page
Bird....

Posted By: autoxcuda

Re: Know where I can buy a carbide burr like this one? - 07/07/11 05:54 PM

Enco and Rutland Tool have better deals than Grainger or McMasterCarr.

That flute spacing looks like aluminum vs a cast iron cutter?

Posted By: sixpackgut

Re: Know where I can buy a carbide burr like this one? - 07/07/11 06:15 PM

some of these look close

http://www.thefind.com/hardware/info-carbide-burr-bit#page=7&local=0

Posted By: Hemi Allstate

Re: Know where I can buy a carbide burr like this one? - 07/07/11 06:21 PM

I have used these. They have quite a selection.

http://www.monstertool.com/monster_tool_burr_monster.html

Long Shank here.
http://www.monstertool.com/ProductData/Burrs-Long_Shank.html

Posted By: gbolten480

Re: Know where I can buy a carbide burr like this one? - 07/07/11 06:31 PM

Here is a page from out of the ENCO catalog.

http://www.use-enco.com/CGI/INPDFF?PMPAGE=251&PMCTLG=00

The tricky thing may be the shank length - I believe most of these are shorter - though it should give a good starting point. Hope it helps, in your search.

Posted By: MR_P_BODY

Re: Know where I can buy a carbide burr like this one? - 07/07/11 09:09 PM

All my burrs are 6" except one.... its a special made
12" OAL that I got from one of the guys in the head
porting lab at work

Posted By: AAR-B4

Re: Know where I can buy a carbide burr like this one? - 07/07/11 09:18 PM

Have you looked at Powerhouse?
http://www.powerhouseproducts.com/ph/abrasives-cutting-1/solid-carbide-burrs.html

Posted By: Crizila

Re: Know where I can buy a carbide burr like this one? - 07/07/11 09:21 PM

Kinda dull in color to be carbide??

Posted By: classracer

Re: Know where I can buy a carbide burr like this one? - 07/08/11 12:38 AM

I get some of the burrs I use from BLP Products here in Orlando. I get some special or custom burrs from Mondello Performance in Tenn.

Posted By: BeEtLeJuIcE !

Re: Know where I can buy a carbide burr like this one? - 07/08/11 07:10 AM

Brad .... just to be 100% "correct" in the description of this part(I am surprised that no-one has mentioned this earlier-I furgot to) ...

what you have pictured is a carbide CUTTER ... not a burr. A cutter will tend to walk-around on you(muchO more than a burr) .... and if that happens in the port and then starts banging-around ... it could either severely bend the shank of the cutter ... or/AND damage your grinder..