Posted By: 440W8 Duster
video of 5.81 pass(New Video added)
Posted By: Leigh
Re: video of 5.81 pass - 12/03/13 03:17 AM
Looking and sounding great!
Posted By: jim sciortino
Re: video of 5.81 pass - 12/03/13 04:59 AM
Nice car...... 
Combo???
Combo???
Posted By: WHITEDART
Re: video of 5.81 pass - 12/03/13 05:11 AM
what are some of the details on the motor and trans 
Posted By: fishy340
Re: video of 5.81 pass - 12/03/13 02:27 PM
Posted By: Plumb Wired
Re: video of 5.81 pass - 12/03/13 03:27 PM
Posted By: 1967dartgt
Re: video of 5.81 pass - 12/03/13 05:29 PM
Nice pass, it's starting to come around for a na small block.
Posted By: ProSport
Re: video of 5.81 pass - 12/03/13 05:42 PM
Awesome!
Posted By: Thumperdart
Re: video of 5.81 pass - 12/03/13 07:59 PM
Very nice looking car and equally impressive et`s.............
Posted By: 440W8 Duster
Re: video of 5.81 pass - 12/04/13 12:00 AM
Quote:
what are some of the details on the motor and trans
4in Callies with 2in rod journal
4.185 bore flat top
Coleman/Arrington W8 head 2.18x1.625 titanium valves
heads and intake done by Brett Miller
roller cam spec bye Brett Miller
T&D 1.7 rockers
420 intake with a Dominator flange
comp is 15.4
6.30 Carrillo rod
Glide with a 1.80 gear
29.5x11.5W tire with a 4.56 Dana
![Attached picture 7945848-_mg_7833[1].jpg](https://board.moparts.org/ubbthreads/upload2/7945848-_mg_7833[1].jpg "7945848-_mg_7833[1].jpg")
Posted By: 440W8 Duster
Re: video of 5.81 pass - 12/04/13 12:04 AM
here is another http://youtu.be/B0VDZqjAFCI
Posted By: WHITEDART
Re: video of 5.81 pass - 12/04/13 03:00 AM
nice combo what dose the car weight.. im doing a motor that is very close to yours . brett did his magic on my w8 as well. did you get any dyno numbers..
. brett did his magic on my w8 as well. did you get any dyno numbers..
Posted By: 440W8 Duster
Re: video of 5.81 pass - 12/04/13 09:58 PM
Quote:
nice combo what dose the car weight.. im doing a motor that is very close to yours
No dyno numbers yet will be doing it in a month or so.
The weight is 3085 race weight.
Posted By: J_BODY
Re: video of 5.81 pass - 12/05/13 02:16 AM
That ALL you got??? 
Posted By: WHITEDART
Re: video of 5.81 pass - 12/05/13 03:43 AM
Quote:hope not
That ALL you got???
I bet it ends up some where in the 5.30 range
Posted By: Leon441
Re: video of 5.81 pass - 12/06/13 12:55 AM
Those numbers are almost identical to my R5P7 440. I can almost guess what the HP and torque numbers are.
I am curious to what the cam specs are. Wonder how close they are to my R5P7 engine cam specs.
My little 421W8 only left that hard with an unknown coverter and blew up thanks to some interference with pistons and valves. That's another story. I had to give the converter up and never had that luck with any I had built. The engine was pretty much a gutless wonder that ran like stink on the big end.
I will gladly share my cam numbers on an open forum but, can understand if you want to keep those to yourself.
Leon
I am curious to what the cam specs are. Wonder how close they are to my R5P7 engine cam specs.
My little 421W8 only left that hard with an unknown coverter and blew up thanks to some interference with pistons and valves. That's another story. I had to give the converter up and never had that luck with any I had built. The engine was pretty much a gutless wonder that ran like stink on the big end.
I will gladly share my cam numbers on an open forum but, can understand if you want to keep those to yourself.
Leon
Posted By: W7 Duster
Re: video of 5.81 pass - 12/06/13 02:41 AM
Posted By: 440W8 Duster
Re: video of 5.81 pass - 12/06/13 03:00 AM
Quote:Quote:hope not
That ALL you got???
I don't think it will run that fast but will be happy with a 5.60's.
Posted By: 440W8 Duster
Re: video of 5.81 pass - 12/06/13 03:03 AM
I Will have to ask Brett about it?
![Attached picture 7948629-_mg_7664[1].jpg](https://board.moparts.org/ubbthreads/upload2/7948629-_mg_7664[1].jpg "7948629-_mg_7664[1].jpg")
Posted By: d4rt
Re: video of 5.81 pass - 12/07/13 06:36 PM
Good old Sabin. I miss that place.
Sick Duster!!!
Sick Duster!!!
Posted By: 440W8 Duster
Re: video of 5.81 pass - 12/07/13 09:25 PM
video #2
http://youtu.be/B0VDZqjAFCI
http://youtu.be/B0VDZqjAFCI
Posted By: 1967dartgt
Re: video of 5.81 pass - 12/07/13 09:40 PM
It's got a baby cam in it. I think it needs more cam. What is the altitude you race at?
Posted By: 440W8 Duster
Re: video of 5.81 pass - 12/07/13 09:48 PM
Quote:
It's got a baby cam in it. I think it needs more cam. What is the altitude you race at?
corrected altitude is about 4000ft in Minot,Nd where I race the last 3 years.
In the video it was 600ft that day and 39 degrees with a 20-25 mile an hour head wind coming in at about 1 o'clock.
Posted By: 1967dartgt
Re: video of 5.81 pass - 12/07/13 10:12 PM
I wonder what it would run at sea level?
Posted By: MR_P_BODY
Re: video of 5.81 pass - 12/07/13 10:32 PM
Looks good... is that on race fuel or E-85
Posted By: WHITEDART
Re: video of 5.81 pass - 12/07/13 10:34 PM
Quote:what cam and lifters and carb are you running
It's got a baby cam in it. I think it needs more cam. What is the altitude you race at?
Posted By: pittsburghracer
Re: video of 5.81 pass - 12/07/13 11:27 PM
Quote:
I wonder what it would run at sea level?
You guys that race at sea level are spoiled.
Posted By: 440W8 Duster
Re: video of 5.81 pass - 12/07/13 11:57 PM
Quote:
Looks good... is that on race fuel or E-85
No its not Mike I bought a Bob Book carb and running on C12.I think I need C14.
Posted By: 440W8 Duster
Re: video of 5.81 pass - 12/08/13 12:00 AM
Quote:Quote:what cam and lifters and carb are you running
It's got a baby cam in it. I think it needs more cam. What is the altitude you race at?
Cam was spec by Brett Miller and lifters are Crane Ultra Pro.
Posted By: 440W8 Duster
Re: video of 5.81 pass - 12/08/13 12:01 AM
Quote:Quote:
I wonder what it would run at sea level?
You guys that race at sea level are spoiled.
I don't know but I wish I was close to sea level!!
Posted By: Leon441
Re: video of 5.81 pass - 12/08/13 02:01 AM
600 ft DA is nothing to complain about.
Most sea level tracks I run in the Spring and Fall are doing well to be 600 ft. after 12P.
Leon
Most sea level tracks I run in the Spring and Fall are doing well to be 600 ft. after 12P.
Leon
Posted By: J_BODY
Re: video of 5.81 pass - 12/08/13 02:02 AM
I've been to Fargo in the fall when the DA is around 200 and the temp was 60-65. You'll hit it one day! Still hoping to make it to Oahe next spring or fall....
Posted By: W5DART66
Re: video of 5.81 pass - 12/08/13 06:21 AM
Jesse post cam info if you would like.
I don't keep record of cam numbers they are customers when I am done.
I don't keep record of cam numbers they are customers when I am done.
Posted By: WHITEDART
Re: video of 5.81 pass - 12/08/13 04:46 PM
Quote:that is a very nice car..Quote:Quote:hope not
That ALL you got???
I don't think it will run that fast but will be happy with a 5.60's.
I think 5.60 will come really easy. mph shows good hp for 3000+lb car with a two speed.it is hard to find the right converter. I no a few guys that have tried 4or5 different converters before they find the right one. I bet a protrans 904 will pick you up a tenth or two easy
Posted By: 440W8 Duster
Re: video of 5.81 pass - 12/08/13 06:25 PM
Quote:
It's got a baby cam in it. I think it needs more cam.
Posted By: 1967dartgt
Re: video of 5.81 pass - 12/09/13 06:04 AM
Quote:Quote:
It's got a baby cam in it. I think it needs more cam.
I think I have a bigger one or real close I will have to check I think my lobe lift is 440 with a 1.75 rocker. That's with 422 cubes and only 12.0 compression .
Posted By: 440W8 Duster
Re: video of 5.81 pass - 12/09/13 03:47 PM
Brad I will tighten up the lash when I dyno it to see if it wants more cam.
Posted By: 1967dartgt
Re: video of 5.81 pass - 12/09/13 04:35 PM
When you going to dyno it?
Posted By: 440W8 Duster
Re: video of 5.81 pass - 12/09/13 04:53 PM
hopefully this month but they are pretty busy so he says. As long as I get it done bye Feb. If I cant I might go to wright Mn. to dyno at Line Performance.
Posted By: WHITEDART
Re: video of 5.81 pass - 12/10/13 01:37 AM
keep us posted sound like it is coming around for you
Posted By: kingdust
Re: video of 5.81 pass(New Video added) - 12/10/13 03:48 PM
Quote:nice runs jesse, car looks great. MARK
http://youtu.be/RTDkU8WCjLo
do run open headers or what type of exhaust?
Posted By: 440W8 Duster
Re: video of 5.81 pass(New Video added) - 12/11/13 03:12 AM
Quote:Quote:nice runs jesse, car looks great. MARK
http://youtu.be/RTDkU8WCjLo
Mark I run open headers!
Posted By: kingdust
Re: video of 5.81 pass(New Video added) - 12/11/13 05:13 AM
Quote:yea, sounded like it was crackalackin real good! lolQuote:Quote:nice runs jesse, car looks great. MARK
http://youtu.be/RTDkU8WCjLo
Mark I run open headers!
Posted By: bdaz smblk
Re: video of 5.81 pass - 12/11/13 05:31 AM
Quote:His cam is bigger then mine on the intake and has more duration on intake and exhaust.I have been wanting to change cams in my car for awhile now myself.Quote:Quote:
It's got a baby cam in it. I think it needs more cam.
I think I have a bigger one or real close I will have to check I think my lobe lift is 440 with a 1.75 rocker. That's with 422 cubes and only 12.0 compression .
Posted By: fishy340
Re: video of 5.81 pass(New Video added) - 12/11/13 02:02 PM
5.81 x 1.553 = 9.04ish in the 1/4.That sounds like 775hp to 800 @ that weight.
Posted By: 440W8 Duster
Re: video of 5.81 pass(New Video added) - 12/14/13 12:56 AM
I did run a 5.79 that same day.
Posted By: 1967dartgt
Re: video of 5.81 pass(New Video added) - 12/14/13 04:54 PM
What convertor do you have in the car?
Posted By: 440W8 Duster
Re: video of 5.81 pass(New Video added) - 12/14/13 10:41 PM
It's a JW 8in and stalls at 6250.