Mopar Transmission For sale - 1st Quarter

New in original box Mopar Performance flex plate P4529751. 6 bolt crank flange 7/16" bolt hole 10" converter bolt spacing. This is like new as it hasn't been used but it is old as I bought it many years ago. $50

904 transmission dipstick and tube. $30

New TCI Break-a-way TC 2400 stall torque converter #141200. Includes flex plate to t.c. bolts. $400 https://www.summitracing.com/parts/tci-141200

New in the box B&M Quicksilver shifter #80683. $325

2 finned aluminum 727 trans. pans. Not sure what the additional capacity is but they are about 2" deep. I have media blasted and painted them. No pick-ups. $125 each.

Big block 727 dipstick tube. I have 2. $20 each

Two 727 factory flex plates. 5/16" Bolt holes with 11" bolt circle. $20 each

I have numerous sets of factory flex plate to crank and flex plate to converter bolts. $8 for a set of crank bolts, $5 for a set of converter bolts.

Prices do not include shipping. gt340 at yahoo.com No Paypal.

727, 518 BILLET REAR SERVO KIT

High performance low/reverse billet rear servo kit for a 727, 518, 46RH, and 46RE transmission. The rear servo piston is a 1-piece design that replaces the stock piston, inner spring, piston plug, snap ring, and the after market shim used in performance rebuilds. The piston is CNC machined out of solid billet aluminum so it will not crack like the stock cast aluminum pistons are known for doing. It comes in a kit with a heavy duty stainless steel return spring that will eliminate 1-2 shift overlap, a new seal, and a .075 extra thick retainer made from stainless steel that will not bend around the retaining ring and pop out of the case like the factory steel retainers do. This kit fits 67 and newer 727, 518, 618, 46RH, and 46RE transmissions. I also have a kit that fits the early 62-66 727’s. The price for either rear kit is $80.00 plus shipping. 100% Made in the USA. If you have any questions, or would like to place an order, please email me at mrrandyj@aol.com Thanks!!

727-48RE DUAL RING FRONT BILLET SERVO KIT

Dual ring billet front servo kits for 727, 518, 618, 46RH, 46RE, 47RH, 47RE, and 48RE transmissions. The front servo is responsible for applying the front band during the 1-2 shift. This servo is based off of the highly desired 71 and earlier Chrysler “small pin” servo that is ideal for use in performance transmissions, only this one is much better. The piston and cover are CNC machined out of solid 6061 billet aluminum and the shaft is CNC machined from prehardened 4140 steel. There are 2 return springs custom made out of stainless steel that will help eliminate the 2-3 shift overlap that these transmissions are known for. There is also a o-ring in the cover that seals it to the shaft to stop internal leakage and help more oil get to 3rd gear where it is needed most. The piston has 4 total sealing rings, doubling the sealing capacity of the original Chrysler servos. This is a ready to install kit, all the sealing rings and springs are included. The price for this kit is $125.00 plus shipping.

100% MADE IN THE USA

If you have any questions or to place an order my email address is mrrandyj@aol.com

904 BILLET REAR SERVO KIT

High performance low/reverse billet rear servo kit for a 1967 and newer 904, 998, 999, 500, 42RH, 42RE, 44RH, 44RE Dodge Plymouth Chrysler Jeep or AMC transmission. This rear servo kit features a redesigned 1-piece piston which replaces the stock piston, inner spring, piston plug, snap ring, and the after market shim used in performance rebuilds. It is CNC machined out of solid billet aluminum so it will not crack like the stock cast aluminum pistons are known for doing. You will also get much less internal leakage with the solid 1 piece piston compared to the stock assembly, that means more holding power for the rear band. Included in this kit is the piston, a heavy duty return spring that will help eliminate the 1-2 shift overlap, a new seal, and a .075” extra thick stainless steel retainer that will not bend around the retaining ring and pop out of the case like the factory steel retainers do. This is a complete ready to install kit, no extra parts are needed and it is 100% Made in the USA. The price for this kit is $80.00 plus shipping.

If you have any questions, or would like to place an order, please email me at mrrandyj@aol.com Thanks!!!

47RH 47RE and 48RE Billet Rear Servo Kit

High performance, low/reverse billet rear servo kit for a 1994-2007 47RH, 47RE, and 48RE Dodge Cummins Turbo Diesel and SRT10 Ram truck automatic transmission. This rear servo kit features a redesigned 1-piece piston which replaces the stock piston, inner spring, piston plug, snap ring, and the aftermarket shim used in performance rebuilds. It is CNC machined out of solid billet aluminum so it will not crack like the stock cast aluminum pistons are known for doing. You will also get much less internal leakage with the solid 1-piece piston compared to the stock assembly, that means more holding power for the rear band. Included in this kit is the billet aluminum piston, a heavy duty return spring that will eliminate the manual 1-2 shift overlap, a new seal, and a extra thick CNC machined billet steel retainer that will not bend around the retaining ring and pop out of the case like the factory retainers do. This is a complete ready to install kit, no extra parts are needed. The price for this kit is $90.00 plus shipping.

100% MADE IN THE USA

If you have any questions or to place an order my email address is mrrandyj@aol.com

BILLET DUAL RING ACCUMULATORS

These will fit just about any Torqueflite transmission including the 727, 904, 998, 999, 500, 518, 618, 42RH, 42RE, 46RH, 46RE, 47RE, and 48RE, almost every rear wheel drive transmission from 1962 on up to the 2007 48RE Cummins Turbo Diesel overdrive transmission. These are a great upgrade for all the 727s and 904s and are also perfect for replacing the plastic accumulator that Chrysler switched to in the late 80s. The plastic accumulators are known for cracking and causing problems in performance transmissions. I have done these 2 different ways: First is an exact stock replacement, this one will accept all the stock springs whether they go between the case and the piston or the piston and the valve body. These are perfect for the turbo diesel guys that have tighter aftermarket torque converters, or for the person doing a stock type rebuild on a gas transmission. Second is with a built in blocker rod that will stop the accumulator from moving in the bore and firm up shifts. No need to cut down round stock and make a blocker rod anymore, I did it for you. Comes with all 4 sealing rings. The price on these are $45.00 each plus shipping.
These are 100% Made in the USA. If you have any questions or want to place an order email mrrandyj@aol.com

727-48RE FRONT BAND STRUTS AND BILLET BAND ANCHORS

Heavy duty, double thick, billet steel front band strut and billet front band anchor for a Dodge, Plymouth, Chrysler, or AMC 727, 518, 618, 46RH, 46RE, 47RH, 47RE, and 48RE transmissions. This fits from the 1962 727 transmission, all the way up through the 2007 ½ Cummins Turbo Diesel 48RE, and everything in between. The OEM Chrysler front band struts are prone to bending, and the OEM band anchors are known for breaking in high performance and heavy duty applications. The band strut is CNC machined from 1/4” thick steel, which is twice as thick as the factory strut and it is zinc coated for corrosion protection. The band anchor is also CNC machined from billet steel. Both are made in the USA. The price is $25.00 each plus shipping.
I also have the struts for a 904 transmission, same price
Email mrrandyj@aol.com

BILLET 4.2 and 5.0 LEVERS
Billet steel 4.2 and 5.0 ratio front band apply levers for just about any Torqueflite transmission including the 727, 904, 998, 999, 500, 518, 618, 42RH, 42RE, 46RH, 46RE, 47RH, 47RE, and 48RE. Almost every rear wheel drive transmission from 1962 on up to the 2007 48RE Cummins Turbo Diesel overdrive transmission. These levers are CNC machined from solid billet steel. They are much stronger than the factory powdered metal forging levers, which are known for failing under the higher line pressures that performance transmissions run. The ratio is laser engraved into the tip of the lever in a large font size so it can be easily seen both in and out of the transmission. These are 100% made in the USA. $49 plus shipping. If you have any questions, or would like to place an order, please email me at mrrandyj@aol.com Thanks!!!

SPEEDOMETER BLOCK OFF PLUGS
CNC machined billet aluminum speedometer hole block off plug. These will fit almost every rear wheel drive automatic and manual transmission from 1966 on up. Uses the factory bracket and bolt to secure it to the transmission. Includes a new o-ring. This is a direct bolt in replacement for the factory speedometer adapter, no modifications are necessary. 100% Made in the USA. $30 each plus shipping. If you have any questions or want to place an order email mrrandyj@aol.com

Reverse wound direct clutch pack spring for the 904, 998, 999, 500, 42RH, 42RE, 44RH, 44RE. The stock spring in the direct clutch drum loses its tension at high RPM and causes the direct clutches to drag in 1st gear. This spring is wound in the opposite direction which eliminates that problem and keeps the clutches from burning up and also helps eliminate 2-3 shift overlap. This spring should be used in any transmission that will see 5500 RPM or more. This is a direct replacement for the stock spring, no other parts or modifications are necessary. These springs have been through a shot peening process that drastically increases cycle life and they are 100% made in the USA. $30 plus shipping. If you have any questions, or would like to place an order, please email me at mrrandyj@aol.com Thanks!

b&m 10239 and a 10236. 85.00shipped. will take pp or usps m/o. file too big for 10236 at 4.53

b&m 10236 flex plate. 85.00 shipped. will take pp or usps m/o.

I have a Cummings diesel 618 Overdrive early non lock up tranny. These are the good trannys which do not require a computer. $500.00 plus shipping from Florida blewbyu2bad@aol.com

I have alot of cores available, no special part numbers for HP cars. $200.00 your choice plus shipping from Florida. blewbyu2bad@aol.com

I have everything you need do have handle forgot to put on before pics $1300.00. Tranny, bell with fork, shifter box with shift rods and handle. Plus shipping from Florida blewbyu2bad@aol.com

New Transmission Crossmember Bolt Kit. Includes 4 bolts, eight washers, and 4 nuts. Never installed. $15

70 E body Automatic Floor Shifter. Used, $450 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

70-74 E-B Body Floor Shifter Replacement Plate / With Instruction. New, $70 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Torqueflite Automatic Transmission Flex Plate. Used, $35 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Clutch Linkage Fork Release Rod #3467235. Used, $25 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

A B C E Body Speedometer Gear 27 Teeth White. Fit 833, 904 and 727 Used, $25 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
A B C E Body Speedometer Gear 34 Teeth Green. Fit 833, 904 and 727 Used, $25 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

1962-78 Automatic Transmission Torque Converter Drain Cover. Used, $10 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

46RE Slip Yoke - I picked this up for a A518 swap, but turns out my non-lockup A518 takes a regular 727 yoke. This was used with a 46RE. Not sure if it'll fit later lock-up 46RH's. Uses a 7290 u-joint. $40 shipped from West Sacramento, CA (PP F&F, postal money order, or check). Or $20 local pick up.

If desired, I can include the 7290 weld yoke for a 3" driveshaft, but you'll have to cut off the weld and small section of old driveshaft. I can also toss in the old u-joint and c-clips (still nice and tight, but can use a a good scrub).

1969 B-body Dana 60. 35 spline axles with long studs, powr-lok differential with 3.54 gears, 7290 yoke with Moroso caps and through bolts. has chrome cover. complete with 11x2 heavy duty brakes including drums and parking brake cables. i do not have pictures as it is still in car. spring perches are moved to fit 71 b-body $3000.00

Part number 2660422 never mounted new
$140 shipped lower 48
A bit dusty. Been on my shelf probably 20 years if not more.

I have two NOS new never mounted 4-speed console boots
Part # 2996454
$150 each shipped lower 48
A bit dusty been on my shelf for at least 20 plus years.

Small block Mopar Lakewood bell housing with block plate. $450.00 plus shipping. Payment by postal money order. Please PM me if interested. Thank you,

I'm rebuilding a 70 18 spline gear box out of a 69 Road Runner.Obviously not the original for the car. The VIN on the side pad is A0179693.Anybody out there own or know where this car is?The case is in excellent shape.Will only trade for another case,nothing else is included and only to the owner of the car it belongs in. Time is a factor,so this would need to be done quickly.PM me here. John.

I have a couple rebuilt 4-speed transmission for sale.
18 spline 1970 dual shifter mount $2100
23 spline aluminum main case from A body overdrive. Still has overdrive gears with a b body tail shaft. $1400
A body 23 spline 1968 VIN stamping on pad. $1400
Have Z bars bearing forks and lots of misc small parts. Not enough time to separate and list right now.
PM with questions

Quick Time 6072 H-12 with engine plate
Have all the extra parts when new including bearing retainer ring.
$590 shipped lower 48

have a early a body 4 speed (no vin pad)slip yoke version,moves freely pretty clean inside can text pics if interested must pu in sw michigan $400.00 oboSOLD

Parts arriving for the rebuild next 2 days,once I start this case will be unavailable.

SMR transmissions B/RB to small block transmission adapter kit. Part number SM99-100P for a 6 bolt crank. New in box, the box has been opened but only for inspection, never installed the kit. for info: https://smrtrans.tripod.com/smrtransmissionsintro/id9.html $500 + shipping PM here or phone (716) 655-0625 ask for Gary or leave a message ( this is a land line)

SOLD JW Ultra Bell 92457 Big Block Chrysler to TF727 or A518 Brand new in box $500 + shipping PM here or phone (716) 655-0625 ask for Gary (this is a land line)

Parts for sale 4 sp parts have short tailshaft as well
$1234 email a.oger@hotmail.com

All items brand new never installed and it is the low band apply $1100.00 new. Will sell for $900.00 plus shipping. May seperate but prefer to sell as a package. blewbyu2bad@aol.com

Mopar Big block 10.5” Aluminum bell-housing #2892513 OEM 383/426/440 1970-72 B/E body cars. In as used condition with all threads chased (although bottom bolt threads are not perfect) with no cracks noted. Includes clutch fork pivot bracket. Asking $550 picked up or + shipping from Pa.

for sale NEW TCI StreetFighter Converter,142200 Chrysler, 1967-81 Torqueflite 727, 24-Spline,525.00 plus shipping

727/904 flexplate P4529751 AB 10" x 7/16" bolt performance converter bolt pattern - 6 bolt crank. NOS, expired SFI sticker.

$65.00 including shipping within the 48 states,

*****SOLD*****

Shipped from Florida 32117

Sorry, no PayPal.

locomo@bellsouth.net