Help with ID of some moldings (cast) and bumperettes, etc

I picked up a few things today, and was hoping I might be able to get some help with ID'ing what the applications are ?

Any help appreciated!


I'll start actually with a few badges. Wonder what year the Polara badge would be ? (Part number on it is 2217840) and not sure on the Sport, would it have been Dart Sport I guess ?

Oh, and part number on the 500 is 2901811 (could be 2901611?)

Cigarette lighters...they don't look familiar to me at all...assuming they are Mopar even too as the other stuff is at least.

And onto the little cast molding pieces..

Going off of the first picture, the 4 of them in the upper left are number 3445204.
The center left are 3445205
The bottom ones are 2784824 and 2484825
The upper right are 3504415
The center right are 3504414

(They all look new basically as well which is cool!)

And the bumperettes.. the 4 on the top have the number 2856612 on the back side of the rubber impact strip part.
The other 2 of them, don't see anything on them.

And while we are on a roll..

Would this be a window latch I suppose?

Thanks again for any ideas !

The lighters look like '53-'54 Plymouth and Dodge (and may fit earlier years). I'm pretty sure I'm right but if you're ambitious you can check Google. I've done that several times with parts that I'm unsure of.

Nice thing about Mopar part #s is they seem to ascend numerically as the part is newer; 220-240 seems to be late '60s & early '70s cars, for example.
Guessing on the nameplates & etc: Polara may be '63 fender badge, Sport might be part of Sport Suburban script or Dart Sport, Custom may be later Valiant/Dart. Short cast moldings remind me of A-body vinyl top moldings at the A-pillar. Bumper guards look like Dodge stuff, maybe '66-67, maybe C-body.
Might help to cruise through the Hamtramck Historical site's brochures & options pages.

Thanks for the ideas so far !

The 500 emblem is 69 Coronet. Goes on the fender if it has pins.

The latch looks like 68-70 coupe rear window - you can send that to me

Yes, it has pins, as do the other couple as well..


And as for the latch...

Bumper guards look like 67-69 Dodge Dart. But I believe there is certain year Dodge Coronets used the same cushion.

Would the "500" emblem be the same for 69-70 Charger 500's ???

How close were these parts to Maywood, CA ?

Bumper guards may be 69 Coronet

Don't think the 500 is 70 Charger the rear is pressed on and the grille would need longer studs.

Here's the ones on my Dart

the lil' corner pcs are for cars with vinyl roofs

Not close to Maywood at all..

I got them from an estate sale in Westminster.

And the bumper guards do look close to your Dart , I can't picture a '69 Coronet one off hand.. have to do some more checking still I suppose. (What about the 4 matching ones, would they be rears maybe?)


And on the 500, aside from Coronet, if it's not for a '70 Charger...maybe '69 Charger 500 like you mentioned maybe but knowing it's Coronet at least helps to narrow it down to put it in the classifieds here.

Just need to work out for what now.

They aren't Dart at least... Samy took one of each and tried them on his '68 down at Hotchkis for me today.

Maybe '69 Coronet like mentioned? Need to find one to try them out on one of these days.

I'm pretty sure they make them 68-69 coronet.

Check this:
Coronet Bumper guards eBay

Thanks Steve

Looking around then on ebay a little, there is another 'set' of nos ones listed as front and rear and they actually look the same. would that be right the front and rear ones are the same? If so I guess that would mean I have a complete set perhaps ?

Just have to figure out what the other 2 different looking ones are next.

(I figured out a couple of the little moldings at least, the ones with a single hole are A body least..and figured out a few of the badges as well)

66-67 charger and coronet used bumper guards like those. The bottom ones have a different profile on the cut out that looks like a rear for these cars.

The 4 that look the same, the number molded into the rubber part matches the 1969 ones exactly.. maybe they fit the earlier too then ?

Or maybe the 2 different looking ones are the rears for the ones you mentioned and the other 4 are the '68 9 cars ? (if the fronts are different by chance that is, since the numbers for the inserts at least only seem to show for the 68/9)

Well, noticed something interesting...guess I should have noticed before, but I never looked carefully enough before. I had "assumed" all of the 4 of them were the same, since the rubber inserts are the same. But I was actually looking at them more closely this morning and there are 2 and 2 of them. The rubber bits are the same but the actual shape of the metal parts are not identical.

Maybe they are 2 front and 2 rear perhaps ? Sure would be easier if there were actual part numbers stamped in the steel instead of only molded into the rubber parts.

Do I have to make another trip?

Just to return the ones you have.

(Unless you have a '69 Coronet floating around. )

Nope... Lol.

Oz I think the vinyl top trim is for a duster-demon. Google it and see if you agree...

Which numbers ? The ones with the single hole are A body I found, but the 2 hole ones I haven't worked out just yet.

the 4 similar are two pairs
the difference is left & right

per the A12 RR thread,
these are Plymouth b-body rear - fronts are similar

these are top of a-pillar some A-body w/vinyl top

I think the shortest ones in your first pic are Dart

Thanks for all the help.

I had "assumed" they were front and rear perhaps being different shaped, didn't even occur to me they were 2 pairs of the same being left and right.

And yep on the A body upper ones.

The A12 thread pic is good to see as well, thanks again.