Posted By: 66droptop
PCV,How do I get this piece off the valvecover?? - 04/22/12 11:11 PM
How do I get this black piece off the valvecover to get the pcv off.There is a small baffell inside the cover right where the pcv is..
.jpg "7175270-valvecoverpcv1966dodge003(Small).jpg")
PCV,How do I get this piece off the valvecover??
Posted By: mikemee1331
Re: PCV,How do I get this piece off the valvecover?? - 04/22/12 11:22 PM
isn't there a tang that aligns with a slot on the cover?
Posted By: John_Kunkel
Re: PCV,How do I get this piece off the valvecover?? - 04/22/12 11:25 PM
It should pull straight off...probably stuck from paint/rust.
Posted By: Cab_Burge
Re: PCV,How do I get this piece off the valvecover?? - 04/23/12 04:16 AM
Quote:
It should pull straight off...probably stuck from paint/rust.
Twist it as you try to raise it up to unscrew it away from the valve cover, there a tight fit to start with 
Posted By: 66droptop
Re: PCV,How do I get this piece off the valvecover?? - 04/24/12 12:27 AM
With a little prying it finally popped off.Thanx guys for the info....
Posted By: 66droptop
Re: PCV,How do I get this piece off the valvecover?? - 04/27/12 12:57 AM
So I went shopping for a new PCV at the local shop and all showed the wrong one.So onto Yearone,,,$97.99..Are you ^**#@*&^ kidding me...Is this my only option or can I spray the heck out of the old one..The old one still rattles but is dirty..Don't know for sure if it has been replaced.I have had the car 10 years and I haven't...
Posted By: mikemee1331
Re: PCV,How do I get this piece off the valvecover?? - 04/27/12 01:12 AM
shoot some carb cleaner through it and pop it back on. the rattle is the check ball which only allows one way airflow (out of the cover) and if it still rattles, it's good!
Posted By: hooziewhatsit
Re: PCV,How do I get this piece off the valvecover?? - 04/27/12 01:16 AM
Or just get a cheap generic one, possibly with a new grommet to make it fit the valve cover. If it's not critical that it looks original...
Posted By: 66droptop
Re: PCV,How do I get this piece off the valvecover?? - 04/27/12 01:19 AM
I must look like the one above.It sets in the black part.The ones in the part stores are the push on type.
I might just clean this one up....
I might just clean this one up....
Posted By: astjp2
Re: PCV,How do I get this piece off the valvecover?? - 04/27/12 02:21 AM
That is just a cover, pull it off, see below. Tim
http://www.amazon.com/Stant-10098-Oil-Fi...id=IS5AB8QP9KOM
http://www.amazon.com/Stant-10098-Oil-Fi...id=IS5AB8QP9KOM
Posted By: bigsbigelow
Re: PCV,How do I get this piece off the valvecover?? - 04/27/12 12:50 PM
I cleaned a plastic pcv and a "HEMI" valve cover breather with carb cleaner last summer for my Duster. I pulled them off a set valve covers my father used to have on his car. They both had been sitting for a couple years and I had to put a lot of cleaner through the breather filter to get it clean (the pcv didnt take much). The pcv actually has a Pentastar logo on it. Any way, they are still functioning fine.
Posted By: GTSfanatic
Re: PCV,How do I get this piece off the valvecover?? - 04/27/12 02:51 PM
Quote:
So I went shopping for a new PCV at the local shop and all showed the wrong one.So onto Yearone,,,$97.99..Are you ^**#@*&^ kidding me...Is this my only option or can I spray the heck out of the old one..The old one still rattles but is dirty..Don't know for sure if it has been replaced.I have had the car 10 years and I haven't...
http://www.ebay.com/itm/63-69-Mopar-A-B-...eb0&vxp=mtr
Posted By: BTTG
Re: PCV,How do I get this piece off the valvecover?? - 04/27/12 03:04 PM
Bill is always helping folks out here on MOPARTS
http://www.ebay.com/itm/Mopar-resto-PCV-...=item35b5c54895
http://www.ebay.com/itm/Mopar-resto-PCV-...=item35b5c54895