|
Re: YAAA BUDDY! Re-pop rim blow steering wheels? Coo
[Re: kidmopar]
#961661
03/30/11 01:18 AM
03/30/11 01:18 AM
|
Joined: Jul 2006
Posts: 636
California
sixpaktoogo
mopar
|
mopar
Joined: Jul 2006
Posts: 636
California
|
Quote:
Has anyone actually seen / purchased one of these?  
I bought one of their first ones, which had three cracks on the backside black plastic. They advertized it as not knowing if it was a reproduction or not! What a crock! At the time they had not advertized them as reproductions on ebay. I got it for $167, with a horn switch. Here's my take on them, and I have restored many of these over the years.
(1) Horn switch was no good because who ever tried to install it, put about 30 bends in it, trying to get it in the grooves.
(2) Grooves for the horn switch were full of glue from when the top and bottom were assembled.
(3) Top part is made from some sort of pressed wood board, not plastic as original! It's also painted with brown paint!
(4) The spokes look fairly good, however, where they meet the black backside, they are lower than originals, which makes not only the horn switch contact (grounded side) not touch the spoke, but also a horn switch cover doesn't fit down far enough (even after I sanded some of the edge of it off), and leaves a gap between the cover and the spoke.
I repaired the cracks, woodgrained the topside, sanded out the switch grooves and installed a new switch, and put on the chrome Mylar band. Looks real nice now, with the exception of the gap between the switch cover and the spoke.
Do I think the ones on ebay are worth $495? In a word NO! Typical repro part that could have been real nice if they would have taken the time to research an original. 
|
|
|
Re: YAAA BUDDY! Re-pop rim blow steering wheels? Coo
[Re: sixpaktoogo]
#961662
03/30/11 01:30 AM
03/30/11 01:30 AM
|
Joined: Jan 2003
Posts: 42,714
Spokane Washington
ScottSmith_Harms
Mr Wizzard
|
Mr Wizzard
Joined: Jan 2003
Posts: 42,714
Spokane Washington
|
Quote:
Has anyone actually seen / purchased one of these?
--------------------------------------------------------------------------------
I bought one of their first ones, which had three cracks on the backside black plastic. They advertized it as not knowing if it was a reproduction or not! What a crock! At the time they had not advertized them as reproductions on ebay. I got it for $167, with a horn switch. Here's my take on them, and I have restored many of these over the years.
(1) Horn switch was no good because who ever tried to install it, put about 30 bends in it, trying to get it in the grooves.
(2) Grooves for the horn switch were full of glue from when the top and bottom were assembled.
(3) Top part is made from some sort of pressed wood board, not plastic as original! It's also painted with brown paint!
(4) The spokes look fairly good, however, where they meet the black backside, they are lower than originals, which makes not only the horn switch contact (grounded side) not touch the spoke, but also a horn switch cover doesn't fit down far enough (even after I sanded some of the edge of it off), and leaves a gab between the cover and the spoke.
I repaired the cracks, woodgrained the topside, sanded out the switch grooves and installed a new switch, and put on the chrome Mylar band. Looks real nice now, with the exception of the gap between the switch cover and the spoke.
Do I think the ones on ebay are worth $499? In a word NO! Typical repro part that could have been real nice if they would have taken the time to research an original.
And there you have it!
|
|
|
Re: YAAA BUDDY! Re-pop rim blow steering wheels? Coo
[Re: sixpaktoogo]
#961663
03/30/11 02:27 AM
03/30/11 02:27 AM
|
Joined: Jan 2003
Posts: 6,085
NotRussia
2fast4yourBrain
OP
Whack top Dodger
|
OP
Whack top Dodger
Joined: Jan 2003
Posts: 6,085
NotRussia
|
Quote:
Quote:
Has anyone actually seen / purchased one of these?
I bought one of their first ones, which had three cracks on the backside black plastic. They advertized it as not knowing if it was a reproduction or not! What a crock! At the time they had not advertized them as reproductions on ebay. I got it for $167, with a horn switch. Here's my take on them, and I have restored many of these over the years.
(1) Horn switch was no good because who ever tried to install it, put about 30 bends in it, trying to get it in the grooves.
(2) Grooves for the horn switch were full of glue from when the top and bottom were assembled.
(3) Top part is made from some sort of pressed wood board, not plastic as original! It's also painted with brown paint!
(4) The spokes look fairly good, however, where they meet the black backside, they are lower than originals, which makes not only the horn switch contact (grounded side) not touch the spoke, but also a horn switch cover doesn't fit down far enough (even after I sanded some of the edge of it off), and leaves a gap between the cover and the spoke.
I repaired the cracks, woodgrained the topside, sanded out the switch grooves and installed a new switch, and put on the chrome Mylar band. Looks real nice now, with the exception of the gap between the switch cover and the spoke.
Do I think the ones on ebay are worth $495? In a word NO! Typical repro part that could have been real nice if they would have taken the time to research an original.
Ya sure it's the same manufacturers? I don't see any gap here:
GNPOSBNSwP!Z+MQ~~_12.JPG)
I asked the seller whether the wood-part is plastic or wood and if they would guarantee that the horn switch works.
We'll see...
|
|
|
Re: YAAA BUDDY! Re-pop rim blow steering wheels? Coo
[Re: 2fast4yourBrain]
#961664
03/30/11 04:05 AM
03/30/11 04:05 AM
|
Joined: Jul 2006
Posts: 636
California
sixpaktoogo
mopar
|
mopar
Joined: Jul 2006
Posts: 636
California
|
Quote:
Quote:
Quote:
Has anyone actually seen / purchased one of these?
I bought one of their first ones, which had three cracks on the backside black plastic. They advertized it as not knowing if it was a reproduction or not! What a crock! At the time they had not advertized them as reproductions on ebay. I got it for $167, with a horn switch. Here's my take on them, and I have restored many of these over the years.
(1) Horn switch was no good because who ever tried to install it, put about 30 bends in it, trying to get it in the grooves.
(2) Grooves for the horn switch were full of glue from when the top and bottom were assembled.
(3) Top part is made from some sort of pressed wood board, not plastic as original! It's also painted with brown paint!
(4) The spokes look fairly good, however, where they meet the black backside, they are lower than originals, which makes not only the horn switch contact (grounded side) not touch the spoke, but also a horn switch cover doesn't fit down far enough (even after I sanded some of the edge of it off), and leaves a gap between the cover and the spoke.
I repaired the cracks, woodgrained the topside, sanded out the switch grooves and installed a new switch, and put on the chrome Mylar band. Looks real nice now, with the exception of the gap between the switch cover and the spoke.
Do I think the ones on ebay are worth $495? In a word NO! Typical repro part that could have been real nice if they would have taken the time to research an original.
Ya sure it's the same manufacturers? I don't see any gap here:
I asked the seller whether the wood-part is plastic or wood and if they would guarantee that the horn switch works.
We'll see...
Yeah, I'm sure. Maybe they made some adjustments since the first ones. I know Plumbeeper repaired one of the first ones as well. Send him a PM, and see what he says.
|
|
|
Re: YAAA BUDDY! Re-pop rim blow steering wheels? Coo
[Re: rayztoy]
#961666
03/30/11 08:44 AM
03/30/11 08:44 AM
|
Joined: Jan 2003
Posts: 4,783
Ontario, Canada
mccannix
master
|
master
Joined: Jan 2003
Posts: 4,783
Ontario, Canada
|
Quote:
Did Chrysler make the original rimblows in-house, or was it sourced from an outside vendor?
Rimblow wheels as well as several other wheels were manufactured for Chrysler by the company Shellar-Globe in Ohio.
Got one NOS rimblow wheel in the box from them in early 80's.
Zero inventory left and today they wouldn't even know what you were talking about were someone to contact them.
|
|
|
Re: YAAA BUDDY! Re-pop rim blow steering wheels? Coo
[Re: mccannix]
#961671
03/30/11 10:46 PM
03/30/11 10:46 PM
|
Joined: Jan 2003
Posts: 544
Washington, MI
Ashsdad
Whatever you call me, my wife has called me worse.
|
Whatever you call me, my wife has called me worse.
Joined: Jan 2003
Posts: 544
Washington, MI
|
Quote:
Rimblow wheels as well as several other wheels were manufactured for Chrysler by the company Shellar-Globe in Ohio.
I actually work for the company that absorbed/bought Shellar-Globe. Trust me, there is no one there that would even know what you are talking about! I think the longest serving people in our steering wheel group only have about 15 years in...
|
|
|
Re: YAAA BUDDY! Re-pop rim blow steering wheels? Coo
[Re: hemi68charger]
#961672
03/31/11 02:39 AM
03/31/11 02:39 AM
|
Joined: Jul 2006
Posts: 636
California
sixpaktoogo
mopar
|
mopar
Joined: Jul 2006
Posts: 636
California
|
Quote:
Quote:
Can they even sell that to the public saying the horn might not work??
No different than selling a wheel without a tire...
You can get the rimblow and maybe this will work from Shaker..
http://shakerhood.com/product_info.php?cPath=28&products_id=163
The switch doesn't work because they are ruining them trying to jamb them in a groove filled with glue! The ruined switch in the wheel I bought was obviously one of Ben Snobar's. Buying another won't help, unless the glue filled grove is addressed!
|
|
|
Re: YAAA BUDDY! Re-pop rim blow steering wheels? Coo
[Re: sixpaktoogo]
#961673
04/03/11 12:45 AM
04/03/11 12:45 AM
|
Joined: Mar 2004
Posts: 658
WOODGRAINWHEELS.COM Indiana
plumbeeper
mopar
|
mopar
Joined: Mar 2004
Posts: 658
WOODGRAINWHEELS.COM Indiana
|
Quote:
Quote:
Quote:
Quote:
Has anyone actually seen / purchased one of these?
I bought one of their first ones, which had three cracks on the backside black plastic. They advertized it as not knowing if it was a reproduction or not! What a crock! At the time they had not advertized them as reproductions on ebay. I got it for $167, with a horn switch. Here's my take on them, and I have restored many of these over the years.
(1) Horn switch was no good because who ever tried to install it, put about 30 bends in it, trying to get it in the grooves.
(2) Grooves for the horn switch were full of glue from when the top and bottom were assembled.
(3) Top part is made from some sort of pressed wood board, not plastic as original! It's also painted with brown paint!
(4) The spokes look fairly good, however, where they meet the black backside, they are lower than originals, which makes not only the horn switch contact (grounded side) not touch the spoke, but also a horn switch cover doesn't fit down far enough (even after I sanded some of the edge of it off), and leaves a gap between the cover and the spoke.
I repaired the cracks, woodgrained the topside, sanded out the switch grooves and installed a new switch, and put on the chrome Mylar band. Looks real nice now, with the exception of the gap between the switch cover and the spoke.
Do I think the ones on ebay are worth $495? In a word NO! Typical repro part that could have been real nice if they would have taken the time to research an original.
Ya sure it's the same manufacturers? I don't see any gap here:
I asked the seller whether the wood-part is plastic or wood and if they would guarantee that the horn switch works.
We'll see...
Yeah, I'm sure. Maybe they made some adjustments since the first ones. I know Plumbeeper repaired one of the first ones as well. Send him a PM, and see what he says.
A customer sent one to me last fall just to put a new switch in it. It had basically all of the same problems. I sure hope they have improved it since then.
Dave
Dave
|
|
|
Re: YAAA BUDDY! Re-pop rim blow steering wheels? Coo
[Re: plumbeeper]
#961680
01/06/12 05:20 AM
01/06/12 05:20 AM
|
Joined: Aug 2011
Posts: 297
Oklahoma
TinCuda
enthusiast
|
enthusiast
Joined: Aug 2011
Posts: 297
Oklahoma
|
Wow,
I can't wait to get back my real rimblow from Plumbeeper.
I am just kind of excited about it. It was a gift from my wife.
.,
(O O {]{]{]||[}[}[} O O)
1971 Plymouth 'Cuda 440-6
{||O||}
2000 Yamaha V-Max
(O O [========= SRT] O O)
2011 Dodge Challenger SRT 392
.
Making as big as a carbon footprint as I can!!!
|
|
|
Re: YAAA BUDDY! Re-pop rim blow steering wheels? Coo
[Re: radiatorman]
#961684
01/06/12 05:26 PM
01/06/12 05:26 PM
|
Joined: Sep 2010
Posts: 1,551
Sweden
71redcuda
pro stock
|
pro stock
Joined: Sep 2010
Posts: 1,551
Sweden
|
Quote:
I had Doug Lepak do my wheel. WOW!!!! is it friggen nice! No Doubt I would use him again. Looked at some of the repros and for about the same cash I got an artist to do mine. Couldn't be happier! 
Bob
I bought my rimblow wheel from Micael Mordarski,a very nice guy,he did a very nice restortion of the steeringwheel also..He told me afterwards i was the last guy outside usa to buy a steeringwheel from him..The shipping to sweden was around 240$! Lucky for me the shipping was included 
|
|
|
|
|
QBNSwPC1H5!~~_12.JPG)
NOS one:8iDBLULBRj,sg~~_3.JPG)
