Previous Thread
Next Thread
Print Thread
MSD 6AL key on voltage connection #955206
03/21/11 12:26 PM
03/21/11 12:26 PM
Joined: Jun 2003
Posts: 17,452
It's a dry heat
gtx6970 Offline OP
I Live Here
gtx6970  Offline OP
I Live Here

Joined: Jun 2003
Posts: 17,452
It's a dry heat
What is the prefered circuit for the key on signal B+ connection for the MSD box

It's a new M+H Wiring stock underhood wiring harness in a 1970 Road Runner

MSD box is going to be under the battery tray and I plan to use the radiator support for the primary ground and the B+ post on the starter relay for battery positive. And will be routed along the factory fenderwell and firewall wiring but not wrapped into it.

My initial thoughts are the J3 circut off the ignition switch coming thru the firewall bulkhead connector - using the original feed wire for the stock coil ( stock ballast will be there but non-functional)


Re: MSD 6AL key on voltage connection [Re: gtx6970] #955207
03/21/11 02:40 PM
03/21/11 02:40 PM
Joined: Dec 2010
Posts: 115
NY,Poughkeepsie
87MO DAK Offline
member
87MO DAK  Offline
member

Joined: Dec 2010
Posts: 115
NY,Poughkeepsie
MSD boxes should power and ground directly off the battery
,and no where else . The trigger wire (small red ) just needs
a 12 volt key on hot wire , to tell the box to switch on.

Re: MSD 6AL key on voltage connection [Re: 87MO DAK] #955208
03/21/11 03:27 PM
03/21/11 03:27 PM
Joined: Aug 2007
Posts: 5,299
Caracas, Venezuela, SouthAmeri...
NachoRT74 Offline
master
NachoRT74  Offline
master

Joined: Aug 2007
Posts: 5,299
Caracas, Venezuela, SouthAmeri...
actually with a good power coming from alt and healthy wiring, the B+ source it can be wired from alt post too

the KEY source it can be the blue wire ( brown in 70 and lates ) going from ballast to coil.

Or if thinking on remove ballast resistor, then use the blue wire ( all years ) originally feeding ballast and regulator

Re: MSD 6AL key on voltage connection [Re: 87MO DAK] #955209
03/21/11 03:31 PM
03/21/11 03:31 PM
Joined: Jun 2003
Posts: 17,452
It's a dry heat
gtx6970 Offline OP
I Live Here
gtx6970  Offline OP
I Live Here

Joined: Jun 2003
Posts: 17,452
It's a dry heat
Quote:

The trigger wire (small red ) just needs
a 12 volt key on hot wire , to tell the box to switch on.




Any suggestions as to what circuit to get the key on signal from ?

Re: MSD 6AL key on voltage connection [Re: NachoRT74] #955210
03/21/11 03:32 PM
03/21/11 03:32 PM
Joined: Aug 2007
Posts: 5,299
Caracas, Venezuela, SouthAmeri...
NachoRT74 Offline
master
NachoRT74  Offline
master

Joined: Aug 2007
Posts: 5,299
Caracas, Venezuela, SouthAmeri...
Quote:


the KEY source it can be the blue wire ( brown in 70 and lates ) going from ballast to coil.

Or if thinking on remove ballast resistor, then use the blue wire ( all years ) originally feeding ballast and regulator



Re: MSD 6AL key on voltage connection [Re: NachoRT74] #955211
03/21/11 03:48 PM
03/21/11 03:48 PM
Joined: Dec 2010
Posts: 115
NY,Poughkeepsie
87MO DAK Offline
member
87MO DAK  Offline
member

Joined: Dec 2010
Posts: 115
NY,Poughkeepsie
Coming directly off the alt will put lots of noise in the MSD box ,
by going directly to the batt the alt noise will get filtered.

Re: MSD 6AL key on voltage connection [Re: 87MO DAK] #955212
03/22/11 01:10 AM
03/22/11 01:10 AM
Joined: Jan 2005
Posts: 2,366
USA, MI
MarkM Offline
Worthy
MarkM  Offline
Worthy

Joined: Jan 2005
Posts: 2,366
USA, MI
Quote:

Coming directly off the alt will put lots of noise in the MSD box ,
by going directly to the batt the alt noise will get filtered.




The wiring directions explicitly say not to wire it to the alternator post for this reason.

You can get 12v+ switched from the positive side of the electric choke harness.

Re: MSD 6AL key on voltage connection [Re: MarkM] #955213
03/22/11 01:58 AM
03/22/11 01:58 AM
Joined: Jan 2003
Posts: 9,731
las vegas
70AARcuda Offline
master
70AARcuda  Offline
master

Joined: Jan 2003
Posts: 9,731
las vegas
just remember the msd start switch will need to see 12 volts both went the key goes to start and went the key is on run...

some 12 volt circuits go to zero volts went the key goes to start...

take the two wires from the ballast resistor...run and start ...and connect both wires to the msd start switch...


Tony

70 AARCuda Vitamin C
71 Dart Swinger 360 10.318 @ 128.22(10-04-14 Bakersfield)
71 Demon 360 10.666 @122.41 (01-29-17 @ Las Vegas)
71 Duster 360 (10.641 @ 124.17 9/16/16 Bakersfield)
Re: MSD 6AL key on voltage connection [Re: 70AARcuda] #955214
03/22/11 10:57 AM
03/22/11 10:57 AM
Joined: Jun 2003
Posts: 17,452
It's a dry heat
gtx6970 Offline OP
I Live Here
gtx6970  Offline OP
I Live Here

Joined: Jun 2003
Posts: 17,452
It's a dry heat
Quote:


take the two wires from the ballast resistor...run and start ...and connect both wires to the msd start switch...




This is what I'm going to do . Plan is to remove the 2 male spade connectors from the bulk head connector and wire the MSD box into both pinouts on the connector.
That way should the desire to remove all the hotrod stuff arise and put it back to stock. I want it to be as simple and painless as possibile

Re: MSD 6AL key on voltage connection [Re: gtx6970] #955215
03/22/11 11:02 AM
03/22/11 11:02 AM
Joined: Jan 2003
Posts: 69,046
Middlesex County, New Jersey
DirectSubjection Online penguin-006
Tacohead. The First and Only
DirectSubjection  Online Penguin-006
Tacohead. The First and Only

Joined: Jan 2003
Posts: 69,046
Middlesex County, New Jersey
I found a 12-volt keyed source under the dash and hooked my MSD to that.

Turns out I hooked it to the key buzzer - my car starts fine but doesn't shut off until I physically remove the key from the ignition slot.

Re: MSD 6AL key on voltage connection [Re: gtx6970] #955216
03/22/11 11:32 AM
03/22/11 11:32 AM
Joined: Dec 2010
Posts: 115
NY,Poughkeepsie
87MO DAK Offline
member
87MO DAK  Offline
member

Joined: Dec 2010
Posts: 115
NY,Poughkeepsie
Quote:

Quote:


take the two wires from the ballast resistor...run and start ...and connect both wires to the msd start switch...




This is what I'm going to do . Plan is to remove the 2 male spade connectors from the bulk head connector and wire the MSD box into both pinouts on the connector.
That way should the desire to remove all the hotrod stuff arise and put it back to stock. I want it to be as simple and painless as possibile




If the car is still wired the way it cam factory ,
(main feed off alt through the bulk head to the amp gauge
then back out of the bulk head to starter relay or batt?)
You will still be in line with the alt.

What MSD is saying for the box to work the way it should,
is that it needs to be hooked to the battery POS&NEG only
and no where else.The battery will filter out most of the noise in the system .
If you wire it up any other way you could have erratic idle problems,
Fouling plugs ,remember the MSD box feed's the coil all it's power.

6543313-msd102.jpg (140 downloads)
Re: MSD 6AL key on voltage connection [Re: 87MO DAK] #955217
03/22/11 11:49 AM
03/22/11 11:49 AM
Joined: Jun 2003
Posts: 17,452
It's a dry heat
gtx6970 Offline OP
I Live Here
gtx6970  Offline OP
I Live Here

Joined: Jun 2003
Posts: 17,452
It's a dry heat
But if I use the original coil pos connection to supply key start/on voltage signal it's using the ballast resistor .

Running it thru the ballast resistor and I tend to think this is abad idea , correct ?
UNLESS I run a solid wire to bypass it on the backside of the ballast.

It is a MSD dist btw, combined with an MSD blaster 2 coil.

And yes, all the cars body wiring is still stock. One of my goals here is to be able to return it back to stock with minimul effort should the desire to arise sometime in the future.

Re: MSD 6AL key on voltage connection [Re: gtx6970] #955218
03/22/11 12:00 PM
03/22/11 12:00 PM
Joined: Dec 2010
Posts: 115
NY,Poughkeepsie
87MO DAK Offline
member
87MO DAK  Offline
member

Joined: Dec 2010
Posts: 115
NY,Poughkeepsie
Quote:

But if I use the original coil pos connection to supply key start/on voltage signal it's using the ballast resistor .

Running it thru the ballast resistor and I tend to think this is abad idea , correct ?
UNLESS I run a solid wire to bypass it on the backside of the ballast.

It is a MSD dist btw, combined with an MSD blaster 2 coil.

And yes, all the cars body wiring is still stock. One of my goals here is to be able to return it back to stock with minimul effort should the desire to arise sometime in the future.

It should be easy then , hook the main POS & NEG from the MSD box
directly to the battery.
Hook the smaller red wire to the blue wire on the ballast but hook it
up on the same side as the feed ,so if you want to remove it ,it should be pretty simple ,and that way it is not feeding through the ballast.

Re: MSD 6AL key on voltage connection [Re: NachoRT74] #955219
03/23/11 03:09 AM
03/23/11 03:09 AM
Joined: Aug 2007
Posts: 5,299
Caracas, Venezuela, SouthAmeri...
NachoRT74 Offline
master
NachoRT74  Offline
master

Joined: Aug 2007
Posts: 5,299
Caracas, Venezuela, SouthAmeri...
Quote:

Quote:


the KEY source it can be the blue wire ( brown in 70 and lates ) going from ballast to coil.

Or if thinking on remove ballast resistor, then use the blue wire ( all years ) originally feeding ballast and regulator







when I made this quote it was because forgot to add ( twice ), if removing ballast, NEED to splice together brown and blue wires coming from bulkhead to hook there the small red wire of MSD. If not remove the ballast wire going originally to coil is simply enough. Its just a trigger to turn it on, not a power source

Noises on system are actually produced from COIL on stock system, breaker points &/or mechanical regulators, not really the alt, but whatever! Follow the instructions going to batt or starter relay stud. Just take in mind SOME of the ammeter reading can it be some mismatched with the real status

Re: MSD 6AL key on voltage connection [Re: 87MO DAK] #955220
03/23/11 03:12 AM
03/23/11 03:12 AM
Joined: Aug 2007
Posts: 5,299
Caracas, Venezuela, SouthAmeri...
NachoRT74 Offline
master
NachoRT74  Offline
master

Joined: Aug 2007
Posts: 5,299
Caracas, Venezuela, SouthAmeri...
Quote:


Hook the smaller red wire to the blue wire on the ballast but hook it
up on the same side as the feed ,so if you want to remove it ,it should be pretty simple ,and that way it is not feeding through the ballast.




Partially true... On start moment, it will be triggered through ballast anyway


Advertisement
Forum Statistics
Forums32
Topics193,815
Posts2,261,739
Members25,802
Most Online1,424
Jun 20th, 2018
Moparts Newest Topics
Where to stay in OKC
by carcrazyguy. 03/21/19 12:09 AM
Where to find w2 replacement valves
by viperblue72. 03/20/19 11:34 PM
Shock settings, radial to bias
by justinp61. 03/20/19 10:56 PM
Viper calipers
by 70rrclone. 03/20/19 10:32 PM

Powered by UBB.threads™ PHP Forum Software 7.7.1